|
Tender For Special Repair To Stps Of Central And North Zone And Provn Of Shed For Parking Of 50 Capacity Of Two Wheeler/ Bicycle And 02 X Car For Patients/ Troops At Kirpan Div Mi Room Under Ge (North) Binnaguri; 1 Dismantling floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles to store and rubbish off the premises including taking downcement plaster complete all as specified and as directed. 2 M&L for non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11Sqm but n. exc. 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in whiter or coloured cement to match as in floor over andincludingcement screed bed / backing layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed. (Note: screed bed shall also deemed to be included in the quoted rate by the contractor). 3 M&L for glazed ceramic coloured tiles 350x250x7/450x350x7mmthick for work on vertical surface such as skirting, dado, set & jointed in cement slurry and pointed in white or coloured cement to match with 10mm thickrenderingin CM (1:4) as rough surface on vertical surfaces as backing coat of wall tiles complete all as specified and as directed. 4 Taking up or down steel tubing and connections, including cleaning for refixing or removal to store of 15 mm bore complete all as specified and as directed. 5 Taking up or down steel tubing and connections, including cleaning for refixing or removal to store of 20 mm borecomplete all as specified and as directed. 6 S&F of Tubes, medium grade, 15mm bore, galvanised, with all fittings and fixed complete to wall and ceilings or laid in floors complete all as specified and as directed. 7 Refixingold 15mm bore GI tubing and connectionson new or old position (walls, ceiling, floor etc) complete all as specified and as directed. Note: The serviceable Tubing obtained from taking down shall be reused 8 S&F of Tubes, medium grade, 20 mm bore, galvanised, with all fittings and fixed complete to wall and ceilings or laid in floors complete all as specified and as directed. 9 Refixingold 20mm bore GI tubing and connectionson new or old position (walls, ceiling, floor etc) complete all as specified and as directed. Note: The serviceable Tubing obtained from taking down shall be reused 10 Demolition of RCC as inslab beam lintels, shelves chajjas reinforcement cut as required to facilitate demolition complete all as specified and as directed. 11 M&L for RCC 1:1.5:3 Type A1 ( using 20 mm graded stone agg) as inslab supported on walls chajjas complete all as specified and as directed. 12 M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 13 Dismantling water tanks and removing to store of any capacity of description 500/1000 ltrs complete all as specified and as directed 14 S&F 1000 ltrs capacity rotational moulded polyethylene water storage(cylindrical vertical with closed top) hoisted and fixed in positions all specified in SSR Part I complete all as specified and as directed. 15 S&F in repairs 20 mm dia PVC ball cock (PVC floatvalves) complete high pressure with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut complete all as specified and as directed 16 S&F in repairs 20mm bore Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all complete as specified and as directed. 17 Taking down Chowkatswith shutter n.exc 1.5 Sqm each without taking off shutters from the frame and removing from site complete all as specified and as directed. 18 Taking down chowkat with shutter exc 1.5 sqm and n. exc. 4.00sqm each without taking off shutters from frameand removing from site complete all as specified and as directed. 19 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plu 20 s side shall be acceptable but no extra payment on this account shall be made etc ,complete all as specified and as directed. 21 S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed. (Note: stainless steel butt hinges and necessary fittings shall be paid separately) 22 M & L for providing plain cementconcrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and as directed. 23 S&F of 100 mm long Stain less steel butt hinges complete all as specified and as directed. 24 S&F of 150mm long aluminum anodised barrel tower bolt of extruded section complete all as specified and as directed. 25 S&F of aluminum handles cast type anodised 150mm of size complete all as specified and as directed. 26 M&L for sliding door bolt of 300mm long plateAluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. 27 All as per item No 26above but without glazing bars complete all a specified and as directed. 28 S&F mild steel work such as window guard bars and similar work conforming to Fe – 290 Grade – E 165 complete all as specified and as directed. 29 S&F mild steel Framed work as in doors or gates,Ladders of angle or other section Fe-410-W(Gde-E-250)Quality-B with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering.Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (including steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified and as directed. 30 S&F in repairs steel ventilator with top hung shutter including hinges, steel peg stay as per drag No, CESZ/2018/TD-07, Sheet 1/3 to 3/3 complete all as specified and as directed 31 M&L preparation of new surface of steel any description over 10 cm in width or girth not otherwise described two coat & synthetic enamel paint over a coat of red oxide complete all as specified and as directed. 32 M&L for preparation of old steel and iron surfaces of any description not otherwise described over 10 Cm width or girth and applying one coat of synthetic enamel paint 1st quality complete all as specified and as directed 33 Hacking out old broken glass (any thickness,size,or description) from wooden frames or glazed with putty or fixed with wooden beads complete all as specified and as directed.. 34 S&F3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in square n.exc 0.5 Sqm in each pane complete all as specified and as directed. 35 S&F in repairs 15mm dia fancy type Bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. 36 S&F in Repairs15 mm diaCP cast copper alloyangle cockfancy type screwed for iron pipe and fixed complete all as specified and as directed. 37 S&F in Repairs10 ltr capacity PVC flushing cistern low level white colour with inlet ball valve float and handle including brackets including PVC connection 450 mm long, PVC flush pipe of reqd length ,and connections to pipe etc complete all as specified and as directed 38 S&F in repairs vitreous chinasquatting panOrissa pattern of size 580x440mm white with integral foot rests(excluding flushing cistern and flush pipe) with P or S trap front or back inlet etc including connection to trap and flushing pipe and provision of Cement concrete bedding complete all as specified and as directed in repairs including demolition of existing one 39 S & F in repairs vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm sizeincluding CP waste coupling, PVC connection 450 mm long, waste pipe removing the existing Basin, cutting for and pinning ends of brackets or erecting stand. complete all as specified and as directed. 40 S&Fin repairs15 mm bore pillar taps, capstan head, cast Copper alloy,chromium plated, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed. 41 Supply and fixing in repairs 600x450 mm mirror of selected quality glass, mounted on wall with chromium plated brass screws and cup washers including pvc frame etc complete all as specified and as directed. 42 S&F PVC connection pipe 15mm size withPTMT nuts of length 450mm complete all as specified and as directed. 43 S & F Grating doom 125 mm dia with waste hole/without hole of PTMT (Minimum weight 40gms) complete all as specified and as directed. 44 Taking down cement plaster on wall / Ceiling of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. 45 Demolition of brick work built in cement mortar of any description,etc complete all as specified and as directed. 46 M&L for brick work with fly ash bricksstraight or curved on plain exc 6mmean radius built in cement mortar 1:6 complete all as specified and as directed. 47 M&L for rendering 5 mm thick cement plaster on ceiling in cement mortar(1:3) finished the surface even and fair complete all as specified and as directed. 48 M&L for rendering 15 mm thick cement plaster onfair face ofsurfaces of brick work or concrete surface in cement mortar(1:6) finished the surface even and fair complete all as specified and as directed. 49 M&L for 15 mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers first layer of 10 mm thick and top layer of 5 mm thick plaster with liquid water proofing compound@ 200ml per bag of cement or as per manufacturers instructions finishing the surface even & fairwithout using extra cement complete all as specified and as directed. (NOTE :Liquid Water Proofing Compound shall be measured and paid separately under relevant item of this Schedule A) 50 Supply only liquid water proofing compound complete all as specified and as directed. 51 M&L for applying two coats of exterior emulsion paint(weather coat) over a coat of exterior primeron a new plastered surfaces of walls including projection, RCC jallies & post etc including necessary preparation of surfaces complete all as specified and as directed. 52 M&L forpreparation of newly plastered ceiling surfaces and applying three coats of whitewash on wall complete all as specified and as directed. 53 M&L for preparation of newly plastered surface and Applying two coats of oil bound distemper over a coatwall care putty over plastered surfaces including priming the surface complete all as specified and directed 54 M&L for preparation of old plastered surface and Applying two coats of oil bound distemper over a coatwall care putty over plastered surfaces including priming the surface complete all as specified and directed 55 M&L for preparation of Old decorated surface of ceiling and applying twocoats ofWhite wash complete all as specified and as directed 56 M&L for complete removal of old existing plasteredsurfaces of walls including cornices, pilasters and other wall features etc by washing rubbing down and stoppingand applying and finishing the walls withpremium acrylic smooth exterior weather proof paint with silicone additives of required shade (luster paint) applied @1.43 ltr/10 sqm over and including priming coat of exterior primer applied @0.902ltr/10 sqm complete all as specified and as directed. 57 Demolition of cement concrete (un-reinforced ) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and as directed. 58 M&L for 75 mm thick cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate in plinth protection finished fair and even without using extra cement including forming necessary joints 12 mm wide to the full depth of PCC at every 3 meters and every change of direction and filling the same with & including bitumen and sand 1:3 by weight of grade Acomplete with and including necessary form work etc complete all as specified and as directed. 59 M&L for75mm thick PCC 1:4:8 type D-2 as in sub base using 40mm graded mechanically crushed stone aggregatecomplete all as specified and directed 60 M&L for 25mm thickpre-polished and chemically treated smooth finish exterior grade coloured chequered tile (300X300)as in pathincluding 15 mm thick Screed bed in CM 1:6 all as complete and as specified anddirected. 61 M&L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M35 grade with approved colour, design & pattern as in footpath, parks, lawns etc. of required strength, thickness and size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand,compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed. 62 M&L for cement concrete type B-1, 1:2:4 (12.5mm graded aggregate), 40mm thick as floor finish without using extra cement, complete all as specified and as directed 63 Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.bedded and pointed in any mortar including removing of demolished material from work site complete all as specified and as directed. 64 M & L forkota stone slab (polished) in flooring 18 to 20 mm thick area of each tile exceeding 0.18sqm over and including 20mm thick cement screed base in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. 65 M&L for kota stone slab polished 18 to 20mm thick in riser or steps, skirting, dado and pillarlaid over 10 mm thick screed bed cement screed (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. 66 M&L for providing plain cement concretetype B0 1:2:4 with using 12.5mm graded stone aggregates in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed. 67 Dismantling posts or struts (Wood, Steel or RCC) any section embedded in natural ground, including taking out embedded portion and making good disturbed ground complete all as specified. NOTE:- The vertical ground above GL shall be measured for the purpose of payment towards work done. 68 Excavating in post holes (or similar holes) n exe 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/loose soil andwatering and removing surplus soil to a distance complete all as specified and as directed. 69 M&L for cement concrete1:3:6 type C2(using 40mm graded stone aggregate) asin foundationfillingand mass concrete complete all as specified and as directed. 70 S&F mild steel posts and struts in fencing including cuttingtops to shape as directed, drillingholes, notching for wire etc; flat iron fillets (for securing wire mesh/welded steel wire fabric etc) including all necessarydrilling, bolting or rivetingetc, andsimilar work conforming to Fe-290 Gde E-165,complete all as specified and as directed. 71 Supply only chain link MS galvanised fencing of any size or type complete all as specified and as directed. 72 Fixing only chain link fencing including lines wires any mesh size and type of any standard rails straining bolts etc including provision of binding wire complete all as specified and as directed. 73 S & F Galvanised, 2 strand, steel barbed wire 2.24 mm dia, barbed with 2mm dia, barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossings with and provision of galvanised mild steel pins etc., complete all as specified and as directed. 74 Taking down or demolition and breaking up drain pipes(SGW,AC,PVC SWR)75/ 100 mm dia complete all as specified and as directed. 75 S&F 75 mm bore PVC(SWR) pipe socketed in any length with rubber ring joints,laid in trenches or in floorscomplete all as specified and as directed. 76 S&F 110 mm bore PVC (SWR) pipes single sockets in any length with rubber ring joints fixed to wall or laid in floor complete all as specified and as directed. 77 S&F PVC(SWR) 75mm bore bends, diminishing pieces or tapers complete all as specified and as directed. 78 S&F PVC(SWR) 110 mm bore bends, diminishing pieces or tapers complete all as specified and as directed. 79 S&F of PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement outer dia 75 mm cement concrete (1:2:4), type B1 including complete all as specified and as directed. 80 Taking down existing tarfelt including tiles, lime concrete & screed bed complete from roof surfaces including parapets and lowering and removing the same to a distance exc. 50m and n. exc.100m including roughening ofold concrete surface of roofby wire brushing and cleaning the surface to remove all loose dust etc complete all as specified and as directed. 81 M&L for 10mm thick screed bed or bedding layers in cement mortar (1:4) with water proofing compound @200ml per bag of cement in order to maintain proper slope over existing roof surfaces for laying waterproof coating finished even and smooth without using extra cement complete all as specified and as directed. 82 M&L for water proofing treatment to RCC roof slab, includingparapet comprising with the following courses of treatment/specification from bottom to top :-(a) Applying bitumenous primer @ 0.4 ltrs per Sqmover plastered surfaces of roof including parapet surface. (b)Over the priming coat laying one layer APP based polymembric membrane of approved manufacturer 3 mm thickweightnot less than 3.6 Kgs per Sqm reinforced with non woven polyester fabric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a heightof 60cm (min) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (Note:- (i) Laying APP based polymeric membrane shall bedonetorch on method or as per manufacturers instructions.(ii)A minimum overlap of 100mm and 75mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturers instruction.(iii) Applying two coats of Aluminum paint over APP membrane.)(iv) Treatment shall be done by authorise applicator of the firm(v) Cutting groove in brick wall 75 mm wide & 65 mm deep and sloping horizontal face of groves with cement mortar 1:3 , complete all as specified. 83 Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. 84 M&L for Rolled mild steel framed work in tubular trusses such as roof trusses,trussed,purlines, crane gantries, rails and fastenings and heavy bracket framingincluding distance pieces, cleats etcs including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St 240 complete all as specified and as directed. 85 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. 86 Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting outin Soft/loose soilcomplete all as specified and as directed. 87 Excavating in post holes (or similar holes) n exe 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/loose soil andwatering and removing surplus soil to a distance complete all as specified and as directed. 88 Removing excavated material (soil) exc. 50m and not exc 100m depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed. 89 Supply and fixedPre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in as in ridges, valley, eaves, etc with self tapping screws complete all as specified and as directed. 90 M&L for Sand filling under floors or in foundations including watering and consolidation including Spreading and leveling in layers n exc. 40 mm thick complete all as specified and as directed. 91 M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and leveled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. 92 M&L for 100 mm thick cement concrete type D2 1:4:8with 40 mm graded stone aggregate as in Sub base etcall as specified and as directed 93 M&L for PCC machine pressed precast apex stone, kerb stone, or similar articles of PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) of size 410 mm x 300 mm x 100 mm, set and jointed and pointed in cement mortar (1:4) finished even & smooth using extra cement. complete all as specified and as directed. 94 INTERNAL ELECTRIFICATIONTaking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit includingremovalof batten/ conduit/ gutties/ wooden boards/ switches/ sockets/ regulators/ light fittings etc and separating the serviceable items like fan regulators and light fittings for re-use under respective items and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified. 95 Taking down carefully existing old/unsv sub main wiring of any size/description as existing at the sit including making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified. 96 M&L for concealed conduit point wiring with 1.5 Sqmm (nominal cross-sectional area) PVC insulated unsheathed single core copper cable working voltage 1100 volts grade conforming to IS-694 with stranded copper conductor in and including PVC conduit of adequate size with allaccessories (including cutting chases & making good the disturbed surface to its original specification) including MS sunk box, 3mm thick hylam sheet top cover fixed by means of brass machine screw and cap washer including size 1.5 sq mm (nominal cross sectional area) PVC insulated unsheathed single core multistranded copper conductor cable as earth continuity conductor connected to main switches/DBs or common earth dolly for one light point controlled by one way switch complete all as specified and as directed. 97 All as per item No 96 here in before butfor one Ceiling Fan / exhaust fan point controlled by one, one way switch and regulator 98 All as per item No 96 here in before but for one 3 point 5 Amps switch socket outlet point controlled by one switch on the same board. 99 All as per item No 96 here in before butfor one 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board . 100 All as per item No 96 here in before but for one light point controlled by one, two way switch 5 Amps 101 All as per item No 96 here in before butusing 2.5 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket combination point including running of2.5 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly. 102 S&F of switch piano flush type 5/6 amps single pole one way complete all as specified and directed. 103 S&F switch piano flush type 5 amps single pole two waycomplete all as specified and as directed 104 S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified and directed. 105 S&F of socket outlet 2 in 1, 5 Pin 5/15 Amp multipurpose 230 volt flush type complete all as specified and as directed. 106 S&F of switch piano flush type 15/16 amps single pole one way complete all as specified and as directed. 107 S&F of Switch socket combination2 and 3 Pin, 5/6 amps, multipurpose flush non shutter, non inter locking type white ivory finish complete all as specified and as directed. 108 S&F switch socket combination 2 in 1, 6 pin 5/6 amps and 15/16 amps multipurpose, white/ivory finish flush non shutter non inter locking type complete all as specified and as directed. 109 S&Fceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and as directed. 110 S & Flamp holder, insulated body, with back plate suitable for batten/anglefittings complete all as specified and as directed. 111 S&FLED white glass Lamp 1x9/10 Watt 230V Base-22 complete all as specified and directed. 112 S & F deluxe fan Electronic regulator 120/280 volts AC 50 Hzs rotary stepwhite/ivory finish complete all as specified and as directed. 113 S&F in repairhylam sheet 3 mm thick white in colour of size 120 mm x 120 mm including taking down existing unserviceable. complete all as specified and as directed. 114 S&F in repair hylam sheet 3 mm thick white in colour of size 120 mm x 170 mm including taking down existing unserviceable. complete all as specified and as directed. 115 S&F in repair hylam sheet 3 mm thick white in colour of size 200 mm x 100 mm including taking down existing unserviceable. complete all as specified and as directed. 116 S&F in repair hylam sheet 3 mm thick white in colour round type of size 80 mm dia including taking down existing unserviceable. complete all as specified and as directed. 117 S&F IP 20, class I, LED light 1X18 W (or nearest next higher wattage) (4feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified and as directed. 118 M&L for Energy saving new generation environmental friendly long life versatile pressure die cast aluminium IP 66 Security light fitting luminaire with high power LEDs as light source and driver of capacity 25 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor cable from ceiling rose to fitting and GI Pipe bracket made out of GI pipe medium grade 1.2 Mtr long 32 mm dia , MS clamp, nut, bolt and washers including taking down the old unserviceable fitting complete all as specified and as directed. 119 S & F Post top lanterns 20 watt LED light fitting ,new generation, energy saving, environmental friendly, long life with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source, spun aluminium canopy, with opal/clear acrylic diffuser and complete with all accessories internally prewired including connecting up with three core twisted flexible copper conductor cable up to ceiling rose and necessary mounting arrangements including taking down old unserviceable fitting complete all as specified and as directed. 120 M&L for sub main wiring with 2 run of 4.00 sqmm (nominal cross-sectional area) PVC insulated unsheathed single core FRLS cable of working voltage 1100 volts gradewith stranded copper conductor includingone run of 4.00 Sqmm (nominal cross sectional area) PVC insulated unsheathed cable with stranded copper conductor as continuous earth wire connected to common earth dolly drawn in 25mm dia PVC rigid non- metallic conduit complete all as specified and as directed. (NOTE : Two run of submain wiring cable alongwith one run of earth wire with and including 25mm dia PVC conduit pipe shall be measured as one unit length). 121 Supply and fixing ofmoulded case circuit breaker (MCCB) four pole Adjustable type 415 volt, 50 Cycles, 25 to 100 Amps of breaking capacity 16 KA after and including taking down / dismantling of old existing unserviceable one complete all as specified and as directed. 122 S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCBS/lsolators complete with and including taking down old unsv one all as specified and directed including taking down the existing unserviceable main switch/ cut out/ DBs of any type/ capacity/ description as existing at site including making good the disturbed surfaces to match with the existing finishes complete all as specified and as directed. 123 S&F in repair MCB, Single pole & neutral, 32 amps, 240 volts, ‘C’ curve, 10KA allcomplete with and including taking down old unsv one as specified and as directed. 124 S&F MCB, Single pole, 6 to32 amps, 240 volts, ‘C’ curve, 10 KAall complete with and including taking down old unsv one as specified and as directed. 125 Material and labour for earthing complete with galvanized steel plate electrodes of size600x600x6mm thick buried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to GI strip 25x4 mm earth lead by means of nuts, bolts, checknuts and washers including 15 mm bore galvanized iron pipe, medium grade for protection of earth lead upto the length of 7.5 meter towards test terminal and 20 mm bore galvanized iron pipe, medium grade for watering, and providing of charcoal and common salt in alternate layers, including necessary earth work in any type of soil and including PCC pit in PCC 1:2:4 with provision of wire mesh and funnel, complete all as shown in electrical plate No 3 of SSR Part- I including testing on complete all as specified and as directed. 126 Material and labour for earthing complete with galvanized steel plate electrodes of size600x600x6mm thick buried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to GI wire 4.0 mm dia mm as earth lead by means of nuts, bolts, checknuts and washers including 15 mm bore galvanized iron pipe, medium grade for protection of earth lead upto the length of 7.5 meter towards test terminal and 20 mm bore galvanized iron pipe, medium grade for watering, and providing of charcoal and common salt in alternate layers, including necessary earth work in any type of soil and including PCC pit in PCC 1:2:4 with provision of wire mesh and funnel, complete all as shown in electrical plate No 3 of SSR Part- I including testing on complete all as specified and as directed. 127 Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations of poles etc. and getting outincluding trimming the sides and forming bottom surfaces to required levels in soft/loose soilcomplete all as specified and as directed. 128 Returning, filling in, including spreading, leveling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and as directed. 129 Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and leveling complete as specified and directed . 130 Supply and laying sub class B bricks of size230x125x73mm(+/- 10% tolerance limit) for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified and as directed. 131 Laying only old burnt old sizebricks,straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection complete all as specified and as directed. 132 Horizontal boring suitable for 50mm bore steel tubing, under road/ pavement / hard standing etc.,not exceeding 10 Metres in length, in any type of soil, suitable for passing through up to 50 mm bore, galvanised steel tubing,complete all as specified and as directed. 133 Supplying and fixingGalvanised mild steel pipe /tubing,light grade complete with all fittings of 40 mm bore dia, laid in trenches / under roads, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers as in cable protection complete all as specified and directed. 134 Disconnecting & taking out defective under ground LT cable from trenches, pole, pipe,floor ,wall etc including bricks ,GI pipes and removing from work site of unserviceable material and keep serviceable material for reuse in safe custody of any size complete as directed (Note:- Excavation/earth work shall be measured & paid separately under relevant item of this schedule) 135 Supply, laying ,jointing andtestingLT underground electric power cable crossed linked XLPE insulated, two or more core galavanised steel strip or wire armoured / PVC insulated armoured cableheavy duty electric cable with aluminium conductor 1100 volts grade, cross-sectional area 10 sqmm 4 core laid in trenches / laid under floor or fixed to walls/on poles / in ducts or passing through pipesetc fixing and connecting accessories such as Aluminium cable lugs, cable glands , nut , bolts , washers etccomplete all as specified and as directed.Note:(Excavation, earth work, sand cushioning, protection brick and pipe shall be measured and paid separately under appropriate items) 136 Relaying in trenches or passing through pipe, 1100 volts grade,LT electric power UG cables, of any type/Size with and including all fixing & connecting accessories such as Aluminum cable lugs, cable gland, nut, bolts, washer etc complete as specified and as directed. (NOTE: Earthwork & Excavation, GI pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule A). 137 Material and labour for LED street light epoxy powder coated pressure die-cast aluminium housing with weatherproof gasket for LEDs with lens and control gear compartments, pressure die-cast aluminium frame with heat resistant toughened clear glass fixed with SS screws, input voltage 140-270 Volts, delivering lumen equal to/greater than 6000 lumen, system wattage 60 Watt, Ingress protection IP-66 with all accessories including taking down unserviceable light fitting and removing from site complete all as specified and as directed. 138 Material and labour for disconnection of all electric connection and taking down of street light fittings of any type , size , capacity and model removing of unserviceable spares or accessories for repair/ replacement of the same including reconnecting and refixing of street light to its existing position viz pole / high mast andtesting complete all as directed. 139 Material and labour for LED floodlight epoxy powder coated pressure die-cast aluminium housing with weatherproof gasket for LEDs with lens and control gear compartments, pressure die-cast aluminum frame with heat resistant toughened clear glass fixed with SS screws, input voltage 140-270 Volts, delivering lumen equal to/greater than 20000 lumen, system wattage 200 Watt, Ingress protection IP-66 with all accessories including taking down unserviceable light fitting and removing from site complete all as specified and as directed. 140 Material and labour for Digging out incoming and outgoing cables of any sizes from loop near junction box/ feeder pillar box in tranches, cutting burnout uninsulated portion of cable and rectify the defect and relaying the XLPE cable under ground aluminum conductor in trenches and returning and filling the excavated soil and connecting the cables with bus bars including provision of lugs as applicable and testing complete all as specified. 141 Supply and fixing loop in- loop out fuse junction box of internal dimension 250 x 200 x 100mm made of FRP sheet with weather proof canopy and locking screw fitted with and including50 Amp rated 4 way connectors for 3 phase and neutral incoming/outgoing , mounted in the box, fixing on street pole/rail poles including necessary aluminum clamps, suitable glands, lugs and GI nut and bolt and 01 SP of 6 Amp for controlling including taking down old unserviceable junction box all as specified and as directed Note : Contractor shall provide cable lugs andPVC gland of suitable size if required on site for connecting cable in junction box. 142 Supplying and fixing in repair single run 3 core , 2.50 sqmm nominal cross sectional areamultistrandedcopper conductor cable, over all PVC sheathed, 1100 Volts grade confirming to IS-694-2010 (FRLS) heavy dutycable PVC insulatedand PVC sheathed from pole junction box to light fitting complete all as specified and as directed. 143 M&L for PCC (1:3:6) type C-1 using 20mm graded stone aggregate for coping /pedestal of poles including necessary form work, fair finishing to exposed surfaces by using extra cement complete all as specified and as directed. 144 M & L Painting ofsteel pole (swan neck type or straight type) up to 12 mtr heightwith cross arms, clamp of any length and shape for LT overhead line/ for street lightwith two coat of aluminum paint after scratching out old paint, cleaning and exiting surface rust free, preparation of the existing surface,including marking pole numbers in a 15 cm dia yellow circle with number writing with blacksynthetic paint/ Sticker, includingpainting strips in alternate from bottom to top with three strips of black syntheticpaint & two strips of Yellow/ Sky blue paint(as per existing pattern through out the circumference of pole, including removing extra wall papdi ,peel off wall papdi by sand paper and makinggood with putty as per existing thickness and applying one coat of white washing on PCC copping of pole and re-numbering of pole with approved size of letter ( Example - P- 001) with synthetic enamel paint of white colour background and black colour lettering complete all as specified and as directed. 145 S&F Sheet metal enclosure for 2 way Distribution Boards (DB’s), double door, single pole & neutral with 200 amps rated bus bar, IP-43, IK-07 protection suitable for fixing MCBS/lsolators complete with and including taking down old unsv one all as specified and as directed. 146 S&F MCB, Single pole & neutral, 35 to 63 amps, 240 volts, ‘C’ curve, 10KA allcomplete with and including taking down old unsv one as specified and as directed. 147 S & F Energy saving new generation environmental friendly long life versatile pressure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 35 watts with pre wired andnecessary mounting arrangements, provision of new 3 core multistrandedcopper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete including removal of old unsv fitting all as directed 148 Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulatedPVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 6 sqmm 2.0 core with and including all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer etc complete as specified and as directed.(NOTE: Earthwork & Excavation, GI pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule A).
|
