Tender For Special Repairs To Building No P22 Or Md Accommodation At Bikram Enclave Under Ge South Udhampur in India

Work Detail

Tender For Special Repairs To Building No P22 Or Md Accommodation At Bikram Enclave Under Ge South Udhampur; 1 Excavation in trenches not exc 1.5m wide and not exc. 1.5m depth in any type of soil for foundation etc or for shafts, well drain pipes getting out in any type of soil complete all as specifiedc and as directed. 2 Returning fillling in including spreading, levelling watering and well ramming in layers not exc 25cm thick in each layer complete all as specifiedc and as directed. 3 Removing excavated soil to a distance n exc 50m and depositing at alevel n exc 1.5m above the starting point complete all as specifiedc and as directed. 4 Taking down chowkats or frames with shutters(without taking offshutters from frames) areanot exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt), all as specified and directed by Engineer-in Charge. 5 Taking down chowkats or frameswith shutters(without taking offshutters from frames) area exceeding 1.50 square metre andnot exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), all as specified and directed by Engineer-in Charge. 6 Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water. 7 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specifiedc and as directed. 8 Dismantling timber scantlings 40 sq. cm and over in section, in any position and in un framed work complete all as specified and as directed. 9 Dismantling asbestos cement/galvalum sheet/CGI (corrugated , semi corrugated etc) sheets as in roof covering complete all as specifiedc and as directed. 10 Dismantling cast iron pipe & reinforced concrete drain pipes, jointed in cement mortar of any dia upto 100mm complete all as specifiedc and as directed. 11 Dismantling water tanks and removing to store exc 250 & n.exc 500 ltrs of capacity complete all as specifiedc and as directed. 12 Demolition of reinforced cement concrete in roof floor (other than ground floors)beams staircase, landing chajja and similar work complete all as specifiedc and as directed. 13 Demolition of renieforced cement concret not exeeding 15cm thickness (below or above ground level) complete all as specifiedc and as directed. 14 Demolition of cement concrete of any description and in any position not otherwise specifically provided complete all as specifiedc and as directed. 15 Demolition of brick/stone masonry built in CM complete all as specifiedc and as directed. 16 Demolition & breaking up drain pipes (SGSW) of 150mm dia pipe complete all as specifiedc and as directed. 17 Demolition & breaking up drain pipes (SGSW) of 200mm dia pipe complete all as specifiedc and as directed. 18 M&L PCC 1:5:10 type E2 using 40 mm graded brick aggregateas in filling under sunken floors/foundation etc complete all as specifiedc and as directed. 19 M&L for Plain cement concrete 1:4:8 type D-2 using 40mm graded agg as in foundation filling and mass concrete complete all as specifiedc and as directed. 20 M&L for PCC 1:2:4 type B1 using 20mm graded aggregate as in PCC filling in hold fast and similar work complete all as specified and as directed. 21 M&L PCC 1:3:6 type C-1 as in surface channels/drainscomplete all as specifiedc and as directed. 22 M&L for 75mm thick PCC 1:4:8, type D-2by using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed. 23 M&L for reinforced cement concrete type B-1 (using 20mm graded crushed stone graded aggregate work as in Chajjas etc complete all as specifiedc and as directed. 24 M&L for reinforced cement concrete type B-1 (using 20mm graded crushed stone graded aggregate work as in slabs supported on walls , beams etc complete all as specifiedc and as directed. 25 M&L Providing cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 complete all as specifiedc and as directed. 26 M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair complete all as specifiedc and as directed. 27 M&L for providing 75mm thick cement concrete 1:3:6 type C-2 using 40 mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing jointsthroughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weightcomplete all as specifiedc and as directed. 28 M&L for Plain cement conc 1:3:6 type C-2 using 40mm graded agg as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for DWCPE (SN8) 180mm (OD) pipes complete all as specifiedc and as directed. 29 M&L for Plain cement conc 1:3:6 type C-2 using 40mm graded agg as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for DWCPE (SN8) 200mm (OD) pipes all as specified. 30 M&L Pre-castedRCC 1:2:4 type B1 using 20mm graded aggregates for precast cement conc slabs as in manhole/drain covers set in cement mortar1:4. complete all as specifiedc and as directed. 31 Machine pressed (factory made) precast plain cement concrete 1:2:4 type B-1 (20mm graded crushed stone aggregate), kerb stone & the like of size 300mm x 300mm x 100mm thick or of size as approved by GE, with plain fair faces including chamfers, weathering etc, embedding in position/laid in trenches on edges of roads, including excavation in any type of soil, setting in cement mortar (1:4) returning filling and removal of surplus soil/debris to a distance n.exc. 50m from the starting point, complete all as specified and as directed. 32 M&L for Non skid Ceramic coloured tiles (square/rectengular) size 600mmx600mmx7mm to 8 mm thick, in floor etc incl 10mm thick screed bed in cement mortar 1:4 for layingfloor finishes under floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specifiedc and as directed. 33 M&L for Non skid Ceramic coloured tiles 300x300x7mm thick in floor etc incl 10mm thick screed bed in cement mortar 1:4 for layingfloor finishes under floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specifiedc and as directed. 34 M&L for Glazed Coloured Ceramic tiles in vertical surface 600x300x7mm thick incl laid over 10 mm thick rendering in CM 1:4, set and joint in neat cement slurry and pointed in white or colour cement to match complete all as specifiedc and as directed. 35 M&L for Machine cut kota stone slab flooring 20-25 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete including 20mm thick screed bed in CM 1:3 complete all as specifiedc and as directed. 36 M&L for machine cut kota stone 20-25 mm thick in riser of steps/skirting, laid over 10 mm thick rendering in cement mortar 1:3 andjointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specifiedc and as directed. 37 M&L for makrana white marble 18-20mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing types and including bedding in CM 1:4 complete all as specifiedc and as directed. 38 M&L for granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms (in one piece) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade and including 20mm thick screed bed in CM 1:3 complete all as specifiedc and as directed. 39 Moulding of Granite/Kota stone full round moulding complete all as specifiedc and as directed. 40 M&L for sand cushion 20 to 30 mm thick for laying and fixing interlocking tiles complete all as specified and as directed. 41 M&L machine pressed precast concrete coloured interlocking paver block (glossy finish) any shape and size (sample approved by GE) confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement andpigment. complete all as specified and as directed. 42 Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 50 x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made. 43 All as per item No 42 above all as per item above but size 65 x125 mm for double rebate complete all as specifiedc and as directed. 44 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 45 All as per item No 44all as per item above but wire mesh door shutter of size 30mm thick complete all as specifiedc and as directed. 46 S&F 18/19mm thick ISI, termite proof , chemically well pressed, prelaminated particle board exterior grade prelaminated, oneside with decorative choice lamination and other side balancing white lamination fixed with screws to frame work for kitchen cabinetstand cup boards etc includimg 6mm th teakwood beading all around complete all as specified and directedMake;- Win Tuff or its equevelent 47 S&F pre-laminated 18mm thick lead free factory made 100% solid WPC (wood polymer composite) sheet having high natural fiber conter 25 to 30% wood colour sheets with density not less than 500 kg/cum and the weight of sheet of 1 Sqm should be 11 kg (+/- 5%) manufactured by ISO 9001-2015 certified company. the sheet should be 100% water proof, ermite proof, fire ratardant, manufacured by single layer extrusion process with exellent screw holding capacity and shore D hardnes, compete as per direction by Engr-in-Charge. 48 S&F steel window (box type) factory made with side hung shutters including pintolhinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all specified.Note :i)The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3ii) MS fillets, glazing, wire gauge shall be measured and paid separately. 49 Description all as per item as above here in before but without glazing bar complete all as specified.Note :i)The window shall be fabricated as perDrg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3ii) MS fillets, glazing, wire gauge shall be measured and paid separately 50 S&F factory made mild steel ventilators box type with upper top hung shutters and bottom fixed type shutters including pintol hinges,steel peg stay and one shop coat of red oxide primer complete all specified.Note :i)The window shall be fabricated as per Drg No CEUZ/TD/1302/2009 Sheet 1/3 to 3/3ii) MS fillets, glazing, wire gauge shall be measured and paid separately 51 Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work for water tanks and similar work conforming to Fe 290 Gd E-165 all as specified . 52 S&F 4mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specifiedc and as directed. 53 S&F 4mm thick sheet glass frosted ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified. 54 S&F stainless steel wire cloth 0.36mm nominal and average width of apreture 1.40mm and fixed with tinned teaks or wire staple complete all as specifiedc and as directed. 55 M&L brick work with sub class B bricks straight or curved on plan to any radiusbuilt in CM 1:6 complete all as specifiedc and as directed. 56 M&L for hardcore ofbroken stone of guage n.exc 63mm deposited spread and levelled in layer n.exc 15cm thick watered and well rammed to true surfaces complete all as specified and as directed. 57 M&L Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 15mm thick screeding in CM (1:3) finished even and smooth mixed with water proofing compound and applying bituminous primer on roof surfaces @ 0.40 ltr/sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 kg/sqm and provide APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forcedand bonded completely to the surfaceswith min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame)all as specified and directed.Make of APP membrane : STP/IWL 58 Water proofing treatment to the sunken portion applying two coat of two component (1 part Polymer and second part cementations powder) cementations, polymer modified elastomeric, water proofing coating composed of cement, properly selected and graded aggregates, additive and acrylic emulsion polymer as a binder apply first coat of (mix and application as per manufacturer"s instructions) all over floor surface/prepared surface and apply to vertical surface up to 15 cmfrom tilling level, allow to dry 4 to 6 hours. Prepare for apply 2nd coat perpendicular to first coat and allow to dry 4 to 6 hours. All joints of Trap/WC/Soil pipe shall be Properly sealed with ceiling compound/polymer modified mortar using Dr Fixit Pidicrete URP or equivalent, Slope of slab shall be towards and including GI pipe 50 mm dia of suitable length Spout pipe. Providing 15 mm protective screed with cement mortar in 1.3 with WPC (Make: Dr Fixit LW+ or equivalent)within 2 to 3 days of second coat complete all as specified as per manufacture instructions. Make: Dr Fixit Pidifin 2K or other equivalent make complete all as specified and directed by Engr-in-Charge. Note : Water proofing treatment will be done by manufacturer of acrylic based polymer modified cementitious composite compound or through their authorised specialized agency which will further have to give a five years warranty for rectification of any defect if incurred at a later stage,otherwise no payment shall be made to the contractor if water proofing is executed otherwise. 59 S&F stainless steel sliding door bolt plate type250 mm long stove enamelled black with bright bolt not less 12 mm dia bolt with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, complete all as specifiedc and as directed. 60 S&F continuous MS CPpiano typehinges 30mm flap (when opened ), bright finish or electrogalvanised complete all as specifiedc and as directed. 61 S&F stainless steel handle, oval type, stove enamelled black 150 mm long complete all as specifiedc and as directed. 62 S&F 100mm size hasp and staple safty type aluminum anodized with mild steel hinges pin including bolt to hinge plate and fixed with screw complete all as specifiedc and as directed. 63 S&F for 150mm size stainless steel barrel tower bolt of extruded section and fixed.all as specified and directed. 64 S&F stainless steel barrel tower bolts, stove enamelled black, with bright bolt 200mm long complete all as specifiedc and as directed. 65 S&F1st class hard wood small fittings such as brackets of any type, shaped door and window stops and the like including all necessary Labour; articles not exceeding 200 Cu.Cm each complete all as specifiedc and as directed. 66 Supply and fixing of stainless steel cold rolled butt hinges mediumweight 100 mm log fixed to steel /angle iron frame by welding, if required complete all as specifiedc and as directed. 67 All as above but 75mm complete all as specifiedc and as directed. 68 S&F 300mm stainless steel ordinary rat tail rod pattern springs, including roller and roller plate complete all as specifiedc and as directed. 69 S&F Hetich soft closer hinges of stainless steel premium quality complete all as specifiedc and as directed. 70 S&FPVC steel catcher of superior quality all as specified and directed by Engr in charge 71 S&F in repair curtain rod of stainless steel 25mm dia with brackets, stops, end bulbs, rollers etccomplete all as specified and directed. 72 S&F in repair vitreous China wash basin, white, flat back, size 550x400mm excluding tap, chain, plug but including brackets, waste fitting 32mm dia, brass chromimium plated for glazed ware sink, basin,with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specifiedc and as directed. 73 S&F for 600mmx450mm mirror of selected quality glass, mounted on 6mm thickcommercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specifiedc and as directed. 74 S&F water closet (Orissa pattern) including lime concrete bedding, vitreous china long pan orissa pattern 580x440mm, white with integral foot rests (excluding flushing cistern & flush pipe) fixed in repairs complete all as specifiedc and as directed. 75 Supply only cast iron "P" or "S" trap 100mm dia complete all as specifiedc and as directed. 76 Supply only Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern all as specifiedc and as directed. 77 S&F 10 ltr capacity PVC valveless, syphonic action type flushing cistern low level white with inlet, ball valve, float and handle including connetion to pipe but fixed in repair complete all as specifiedc and as directed. 78 S&F C P brass magic eye in main door as per sample complete all as specifiedc and as directed. 79 S&F stainless steel peg set of six as per sample complete all as specifiedc and as directed. 80 S&F plate rack made of stainless stee, 600 x 750X0.55mm including fixing as per manufacturers instruction. all as specified. 81 S&F in repairs 600mm long brass chromium plated towel rail fancey type complete all as specifiedc and as directed. make Jaquar Cat No ACN-1111NM 82 S&F PVC connection 15mm size with PTMT nuts of lengh 450mm complete all as specifiedc and as directed. 83 S&F in repairs of sinks with draining boardmade of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipeincluding beddingin cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specifiedc and as directed. 84 S&F 110 mm bore PVC (SWR) pipes single socketed of pipe wall thickness 2.20mm in any length with rubber ring joints fixed to walls with MS bracket of size 25mmx3mm with necessary nuts, bolts & washer duly painted with black paint complete all as specified and directed. 85 S&F PVC (SWR) pipes 75mm bore single socketed , in any length with rubber ring joints fixed to wallcomplete all as specifiedc and as directed. 86 S&F PVC (SWR) branch piece 110mm bore, single (single Y) equal or unequal pipe wall thickness not less than 2.00mm complete all as specified and as directed. 87 S&F PVC (SWR) junction single 110mm bore, (Single T) equal or unequal with access door pipe wall thickness not less than 2.00mm complete all as specified and as directed. 88 S&F PVC (SWR) junction single75mm bore,(Single T) equal or unequal pipe wall thickness not less than 2.00mm complete all as specified and as directed. 89 S&F PVC (SWR) bend any radius for upto 110mm bore pipe pipe wall thickness not less than 2.00mm complete all as specified and as directed. 90 S&F PVC (SWR) vent cowl 110mm bore pipe pipe wall thickness not less than 2.00mm complete all as specified and as directed. 91 S&F PVC (SWR) vent cowl 75mm bore pipe pipe wall thickness not less than 2.00mm complete all as specified and as directed. 92 S&F PVC (SWR) reducers 110mm bore pipe pipe wall thickness not less than 2.00mm complete all as specified and as directed. 93 PVC (SWR) couplers 110mm bore pipe pipe wall thickness not less than 2.00mm complete all as specified and as directed. 94 PVC (SWR) couplers 75mm bore pipe pipe wall thickness not less than 2.00mm complete all as specified and as directed. 95 S&F PVC (SWR) Floortrap, 75 mm dia of outlet, plain with grating including jointing with solvent cement all as directed. 96 S &F Soap dish holder, fixed in repairs, complete all as specified and as directed. 97 S&F in repairs Corner Glass shelfwith chromium plated guard rails Make JaquarCat No ACN-1171N and equivalent in CERA. 98 S&F in repairs Front Glass shelfwith chromium plated guard rails Make JaquarCat No ACN-1171N and equivalent in CERA. 99 S&F in repairs15 mm dia Wall mixer, WHB mixer & Sink mixer chromium plated screwed down high pressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specifie and as directed.Make : Jaquar or equivalent in CERA/Parryware. 100 S&F in repairs 15mm bore Bib tap Chromium plated complete all as specifiedc and as directed. 101 S&F in repairs 15mm bore angular stop cock with wall flange complete all as specifiedc and as directed. 102 S&F in repairs PVC connection 15mm bore 450 mm long complete all as specifiedc and as directed. 103 M & L 15mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete including taking down all as specified and as directed. 104 M & L 20mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete including taking down all as specified and as directed. 105 M&L in repairs Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20mm complete all as specifiedc and as directed. 106 M&L in repairs Gun metal globe of gate valve with iron wheel head, screwed both ends of size 15mm complete all as specifiedc and as directed. 107 M & L in repairs brass chromium plated shower rose 125mm size with swivel joint fixed to pipe or union of 15mm bore complete all as specifiedc and as directed. 108 S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 liters including all accessories complete all as specifiedc and as directed. 109 M&L for form workto soffits of suspended slabs and similar work not exceeding 200mm thick complete all as specifiedc and as directed. 110 M&L for mild steel steel TMT bars 10mm dia and over cut to length bent to shape reqd ,incl cranking ,bending spirally for hooping columns hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia all as specifiedc and as directed. 111 M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer"s instructions. 112 M&L for Rendering 10mm thick on fair faces of brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specifiedc and as directed. 113 M&L for Rendering 5mm thick on brick or concrete surface as in ceiling in cement mortar 1:4 finished even and smooth without using extra cement complete all as specifiedc and as directed. 114 Supply only liquid integral water proofing compound mixing shall be as per manufacturer’s instructions. Make : PIDILITE or equivalent as per IS-2645. 115 M & L for Complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc by skilled labour with mechanical sander having 1500 - 2700 rpm, with internal dust extraction system for clean environment, and preparation of old plastered/scrapped surfaces of wall/Ceiling by filling cracks by external wall putty/crack fill paste and applying exterior water proof wall care putty @ 1 Kg(undiluted) per sq mtr. of average thickness 1 mm to 2mm over the prepared plastered wall /ceiling surfaces, one or more coats and grinding the puttied surfaces with mechanical grinder for make the surface even and smooth for receiving primer and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives & Color stay technology, Excellent dirt pickup resistance @ 1.79 litre/10 sqm diluted with water as per manufactures instructions over and including priming coat of exterior primer applied @ 0.9 litre (Undiluted)/ 10 Sqm over old/new putty surfaces of wall/ceiling complete all as specified and directed. Note:-Paint using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed. 116 M&L for Preparation of newly plastered surfaces on wall/ roof projections including facia, cornices etc and applying exterior water proof wall care putty @ 1 Kg(undiluted) per sq mtr. of average thickness 1 mm to 2mm over the prepared plastered wall /ceiling surfaces, one or more coats and grinding the puttied surfaces with mechanical grinder for make the surface even and smooth for receiving primer and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives & Color stay technology, Excellent dirt pickup resistance @ 1.79 litre/10 sqm diluted with water as per manufactures instructions over and including priming coat of exterior primer applied @ 0.9 litre (Undiluted)/ 10 Sqm over old/new putty surfaces of wall/ceiling complete all as specified and directed. Note:-Paint to be applying with using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed. 117 Note for item No 115 & 116:-The work for periodical services shall included the following and the rates quoted by the bidder shall included the same :(a)The work pertains to periodical services shall be executed by the contractor as per MOU from authorised applicator through manufacturer of the materials like Exterior Emulsion paint, putty etc approval by the GE.(b)The Contractor shall upload with the documents under cover I "Memorandum of Understanding" (MOU) with at least one of the manufacturers mentioned in the contract, failing which the bid shall be liable to be rejected.(c) Use of scaffolding, trestle, ladders, cradles etc necessary for execution of work and protective measures.(d)Removing of nails, making good holes, cracks etc.(e) Work in patches and in narrow/width, bands, cornices, pilasters etc and cutting in edge of line where necessary. 118 Note :-(f)Spreading and removing covering to doors, windows, floors, fittings etc to protect them from splashes.(g) Washing floor, cleaning glass, joinery, electric fittings, wiring etc, drops and splashes of paint be cleaned to the ensure satisfaction of Engr in Charge.(h)Sample patch of 10 Sqm be repaired considering all the items of periodical and shall be got approved from GE prior to carrying out further work.(j) The work shall be carried out op to 4 storey.(k) Incl removal of vegetation on walls incl roots on wall surfaces. 119 M&L for preparation of steeland iron surfacesexceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat ofprimer complete all as specifiedc and as directed. 120 M&L for applying one coat of wall putty on walls to give uniform surface complete all as specified and directed. 121 M&L for applying two coats of white washing on ceilingincluding preparation of new/ old plastered surfaces complete all as specifiedc and as directed. 122 M&L two coats of oil bound distemperon walls including preparation on new surfaces over a coat of primercomplete all as specified and directed. 123 M&L for two coats of weather proof exterior emulsion paint over a coat of primer including preparation of new plastered surfaces of any description complete all as specifiedc and as directed. 124 Writing letters or figures (Block, Roman, Italic or Indian) n exc. 30 cm high complete all as specifiedc and as directed. 125 S&F for DWCPE (SN8) 180 (OD)/163(ID) mm diameter pipes laid on 150mm thick bed to execute and make sewer line functional all as specified. 126 S&F for DWCPE (SN8) 200 (OD)/175(ID) mm diameter pipes laid on 150mm thick bed to execute and make sewer line functional complete all as specifiedc and as directed. 127 M&L for Mild steel Rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails guides for sliding doors, and vertical posts of pipes sections fixed with angle cleats or other connecting plates, Fe-410-W (Gde - E -250), complete all as specified and as directed. 128 S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. 129 Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power) complete includingfitting such as switch, sockets, ceiling rose, pendants socket,fan regulators any type, rectangular board ,light fittings,terminal boxes etc removing materialsfor taking credit and making good disturbed surfaces of walls floors and ceiling complete all as specifiedc and as directed. 130 Taking down main switches, distribution boards and cut outs etc. of any type and capacity along with the existing boards and removing the same from site and making good the disturbed surface/portion of walls complete all as specified and directed By Engr-in-Charge. 131 Taking down carefully sub main wiring of any nos of wire and size with earth wire on wooden batten/surface conduit/casing caping complete with its all accessories complete all as specified and directed. 132 Point wiring for one light/ fan/bell point controlled by oneswitch using 1.5 Sq mm FRLSH copper conductor cables (multistranded) PVC insulated and unsheathed in and including PVC concealed conduit pipe as per site requirement (size not less than 20mm dia), medium grade with Modular sunken boxes & PVC/metal back plate for mounting modular type switches, sockets & regulators etc with cover plate modular type including supplying and laying PVC insulated and stranded unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire connected to earth dolly includingcutting of chases in wall /ceiling etc and making good the disturbed surfaces match to existing with cement mortar and putty white /colour wash complete all as directed . Make: Havells/ Finolex/ Polycab. 133 All as per item no 131 above but with cable 2.5 sqmm FRLSHfor one 3/5 pin 6 Amp socket outlet point on an independent board. 134 All as per item no 131 above but with cable 2.5 sqmm FRLSH for one 3/5 pin 6 Amp socket outlet point on the same board with other switch. 135 All as per item no 131 above but for one bell/buzzer pointcontrolled by one bell push single pole one way . 136 All as per item no 131 above but for Two way point control by Two two way 6 Amp switch. 137 All as per item no 131 above but for one 3/6 pin 16 amps socket outlet point on an independent board with cables of size 2.50 sqmm. 138 All as per item no 131 above but an independent board with cables of size 4.0sqmm. 139 S&F for modular switch6 Amps single pole one way230 V, 50 Hz, AC , with outer cover complete all as specified and directed by Engr In charge.Make:Legrand/Havell crabtree/L &T 140 S&F Switch modular, flush type, single pole, Two way 5/6 Amp 230 Volts complete all as specified and directed. Make:Legrand/Havell crabtree/L &T 141 S&Fmodular bell push, flush type, single pole, one way 5/6 Amp 230 volts complete all as specified and directed.Make:Legrand/Havell crabtree/L &T 142 S&F for modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC , with outer/inner covercomplete all as specified and directed by Engr In charge.Make:Legrand/Havell crabtree/L &T 143 S&F for modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with outer cover complete all as specified and directed by Engr In charge.Make:Legrand/Havell crabtree/L &T 144 S&F for modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush typewith outer/inner covercomplete all as specified and directed by Engr In Carge. Make:Legrand/Havell crabtree/L &T 145 S&F Lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. 146 S&F LED retrofitlamp of capacity 12 watt, B-22 holder base with polycabonate body and aluminium heat sink warm white/day light complete all as specified and directed. 147 S&F LED retrofitInverter lamp of capacity 9 watt,power backup upto 4 hrs B-22 holder base with polycabonate body and aluminium heat sink warm white completeall as specified and directed.Make-Philips or techno commercial equivalent in approved make 148 S&F in replacement ceiling rose,3 terminal,PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed. 149 S&F in replacement electric bell ding dong type AC 230 Volts, 50 Hz single pole complete all as specified and directed. 150 S&F in replacement electronic step type fan regulator 100 watt 230 volts 50Hz two module C/S deluxe type complete all as specified and directed. Make: Havells Crabtree/ Legrand/ Indoasian. 151 S&F in replacement sheet metal enclosure for MCB DB double door type, single pole and neutral 12 way 240Volts with 200 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed. 152 Supply and fixing in replacement 240V, 10KA "C" curve miniature circuit breaker (MCB) of SPN 40 Amp current carrying capacity in the MCB DB complete with connection testing and commissioning. 153 S&F in replacement MCB Single Pole, 6 to 32 Amps 240 volts, 10KA breaking capacity, convenient to "C" Curve complete all as specified and directed. 154 Supply and fixing in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specifiedc and as directed. Make-Havells LED Pride Plus Neo Batten 10 W Cat Part No LHEXACP7IN1W010 or Equivalent make in Bajaj/C&S 155 S & F in repair LED light fitting 1x9W/10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specifiedc and as directed..Make- Wipro/Bajaj /Philips 156 S& F in replacement LED tube light fittings of 20 wattage Aluminium Extruded Body including rawl/plug ,making connection with and including 23/0.0076 flexible copper wire three core from connector to ceiling rose not more than 1.2 mtr fixed to wall firmly , complete all as specified and directed. 157 S & F LED lights fitting 1x 20W, 230V,AC white/warm white decorative box type with driver,which gets automatically switched ON during Power cut and Run effectively up to 3 Hours, Lumens Capacity-2000lm ,PF-0.9(min) ,colour temp 6500K,CRI>80,IP 20 light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-In-Charge. Make- Havells Pride Plus Inverter Batten cat Part NoLHEXACP7FN1W020 or techno commercial equivalent make in Syska/Bajaj 158 S & F Modular TV Socket outlet single with inner and outer cover required module including TV cable required length from roof complete all as specified and directed by Engr-in-charge. 159 S&F Decorative wall light fixture including LED bulb of 12 W (B-22 Base) Warm White/Day Light made up of polycarbonate body, weather proof, LED light fitting fixture with co extruded polycarbonate body,environmental friendly, energy efficientcomplete with all accessories, prewired and making connection with and including three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp complete all as specified and directed. Make- Havells/Philips/Crompton greaves. 160 S&F in replacement 25 Wattlighting luminaire with unique peanut optics to ensure uniform distribution, higher spacing between poles and maintenance free system for city roads and Streets, 50% Energy Savings, IP66 Protection PC and FG Cover, High Impact Resistance complete including LED Lamps and all accessories including bracket made out of 25mm bore GI pipe (light grade), 1.20 m long made to shape and fixed to existing pole or bldg by means of 2 Nos mild steel flat iron 40x6mm clamps with suitable size bolt, nuts & washers and connecting with three core flexible copper wire of size 23/0.0076 from ceiling rose to existing junction box complete all as specified and directed. Make Philips/ Havells/ Bajaj/ Crompton greaves. 161 M & L for Earthing complete with galvanized steel earth plate electrodes 600 mmx600 mm x6.3 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including galvanized steel earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel including PCC pit in PCC 1:2:4 type B-1using 20 mm graded crushed stone aggregate, RCC framewith 40mm thick RCC cover reinforced with 8mm dia deformed barshandle. including excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 15mm bore main board complete all as shown in electrical plate No 3 connected to main control board all as specified and testingon completion. Note: Excavation earthwork charcoal PCC pit is covered under this item including taking out existing earth plate etc If earth resistance of earthing is not found (2 to 5 Ω) satisfactory earthing shall be redone by the contractor. 162 S&F sub main wiring with two single core FRLSH PVC insulated unsheathed multistranded copper conductor of size 6 Sqmm nominal cross sectional area and one run of 6 sqmm nominal cross sectional area FRLSH PVC insulated unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25 mm dia "medium grade" PVC concealed conduits and fittings, complete all as specified and directed.NOTE: One unit length shall measured as two run of main wire and one run of conduit & earth wire Make: Havells / Finolex / Polycab. 163 Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE.Five star rated with brushless direct current motor (BLDC) with Remote complete all as directed and specified by Engr-In-Charge. Make- Bajaj Energos 35NR or Techno commercial equivalent in Usha/CG 164 Supply, fixing and testing of Main distribution Box(metering Panel) made out of 2mm thick MS sheet of size not less than 800x600x150mm duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, wall mounted/ semi grouted in wall with locking arrangement and provision of tapping for incoming and outgoing electric connections with suitable size of lugs complete all as specified and directed comprising of the following(i) Aluminium bus bar chamber TPN of 200 amps rating (Set of four strip). (ii) Phase indicating lamp Set of three. (iii) Voltmeter (0-450V), three phase, digital type with inbuilt selector switch-01 set(iv) MCCB four pole 415 volts AC 50 Hz, 63 amps rating breaking capacity 10 KA fixed magnetic and adjustable thermal release - 01 No. (v) MCB SPN 230 volts AC 50 Hz, 32-40 amps rating breaking capacity 10 KA fixed magnetic and adjustable thermal release - 04 No. (vi) fixing and connection of existing energy meter - 04 nos(vii) Name Plate holder on each compartment for identification of Accn - 04 Nos(viii) Earthing terminals - 02 Nos(ix)MCB SP 20A 10 KA C series - 01 Nos 165 Supply and fix exhaust fan made of sturdy Engineering plastic body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm including making hole for exhaust fan plastering making good surface all as directed and specified by Engr-In-charge. 166 Supply, laying and testing (in replacement) of cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core 167 S&F Double Walled corrugatedDWC Pipe of size 40 mm including snap fit coupler Pt-II for protection of LT Cable in undergroundall as specified. 168 S &F for 40 mm dia GI pipe "light grade" ISI marked including fittings such as bends, tees, sockets etc fixed on wall/pole or laid in trenches under road crossing/hard standingincluding taking down old /unserveciable existing pipe complete all as specified and directed.NOTE :Excavation and earth work shall be measured & paid separately. 169 Taking down Ceiling fans/Exhaust Fan, cleaning its dust particles oiling,greasing,one coat of synthetic enamel white spray painting with blade ,reassemble the same along with all fittings andhanging the same back to its original position including connecting the wire to ceiling rose etc complete after completing the wiring all as specified and as directed by Engr-in-Charge.Note :- (i) The spares like condensor, ball bearing, cotter pin, nuts & bolts, connecting rods & hooks etc if found defective/damage deemed to be replaced and make the ceiling fans functional. No extra payments will be done on this account. 170 Removing & Refixing carefully Geyser of any capacity including nut bolts,copper conductor cable of suitable size all as specified and directed by Engr-in-charge.Note :- (i) The spares like anchor bolts, plug top, nuts & bolts, connection pipes & heating rod etc if found defective/damage deemed to be replaced and make the water heater functional. No extra payments will be done on this account.

Contact Information