Tender For Special Repair To Building No. P-27 (Officers Married Accommodation) At Nho Dehradun in India

Work Detail

Tender For Special Repair To Building No. P-27 (Officers Married Accommodation) At Nho Dehradun; 1 Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. 2 M&L for brick work with old size full bricksubclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed. 3 Taking down cement plaster on brick or stone wall or concrete surfacesincluding raking out joints, hacking for key and scrubbing down with water etc and removal of debris out side MoD land complete all as specified and as directed. 4 M&L 15mm thick rendering in cement mortar (1:6) on brickor concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. 5 M&L for 10 mm thick rendering on roof,ceiling,chajjas and roof parapetin cement plaster (1:3)and fininshed surface even and smooth without using extra cement complete all as specified and directed. 6 M&L for 15mm thick plastering onbrick or concrete surface in CM (1:4), surface finished even and fair mixed with WPC as per manufacturer"s instruction complete all as specified and directed.Note :- WPC shall be measured and paid separately as supply only. 7 Supply only WPC integral water proofing compound (Liquid type) complete all as specified and directed. 8 Dismantling of plain or corrugated steel sheeting, any gauge, thickness in roof coverings complete all as specified and directed. 9 S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick ofcolour as approved by GE, having tensile strength of 550 Mpa, AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 10 S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of colour as approved by GE having tensile strength of 550 Mpa, AZ-150 as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. 11 S&F rolled mild steel section for Roof trusses (framed), trussed, purlins, crane, gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W(Gde-E-250) quality-Acomplete all as specified and as directed.Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. 12 S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and or riveted or forged into spikes, framed, barred iron door, ladders, fencing work ect. conforming to Fe-290 Gde E-165 complete all as specified and directed.Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account. 13 Demolition of PCC in ground floorand pavings not exc 15 cm thickness below or above ground levelincluding removal of rubbish out side MOD land complete all as specified and directed. 14 M&L forPCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection/hard standing, laid in panel surface finished even & fair, complete all as specified and directed. 15 Demolition of floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises from MoD land complete all as specified and as directed. 16 M&L for coloured vitrified tiles of any design and pattern,as aooroved bythe GE ,double charged, light shade 9 to10 mm thick, as in floor etc incl 15 mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B1b with average water absorption less than 0.05%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 4.0% (Max deviation). Centre & Edge curvature and warpage + 0.20% (Max Deviation). Breaking strength 1200 N (Minimum) and minimum 95% tiles shall be free from visible defects and area of each is as following complete all as specified and directed :-Note: Shade of the tiles including Colour, design and pattern shall be got approved by GE/ AGE(I). 17 Area of each tile exc 0.42 sqm but notexc 1.00 sqm 18 Description same all as per item No.16 but in riser of steps, skirting, dado and pillaretc with over and including10mm thick rendering in CM (1:4) complete all as specified and directed. 19 M&L for non skid, Endura, coloured ceramic tiles12-14 mm thick (Square/Rectunglar), as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles laid with and including over 15mm thick screed bed in CM (1:6), area of each tiles shall be of following complete all as specified and directed :- 20 Area of each tilenot exc 0.11 Sqm. 21 Area of each tilenot exc 0.16 Sqm. 22 Description same all as per item No. 18but in riser of steps, skirting, dado and pillaretc with and includind over 10mm thick rendering in CM (1:4) complete all as specified and directed. 23 M&L for 18-20mm thick granite stone slab (of any type) work (table rubbed and mirror finish polished) with and including necessay notching, chamfering the edges in steps, jambs, pillars, window-cills, cooking platforms and like bedded over and including 15mm thick screed bed in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. 24 S&F Aluminium powder coated three track sliding windows with three sliding shutters, (One with and including stainless steel wire mesh and two with and including 4mm thick sheet glass panes) aluminium sections not less than 1.1kg per metre for bottom track and top track and side track 0.98 kg per metre, bottom shutter frame @0.55 kg per metre, top shutter frame 0.47 kg per metre, shutter sides, 0.47 kg per metre and interlock sides @0.45 kg per metre including aluminium powder coatedgrill of size 50x50mm, 5mm thick suitable nylon beading channel gasket, nylon rollers Maruthi lock with handles and connected itemsetc including taking down existing chowkhats or frames with shutters (without taking off shutter from the frame) of sizeexc 1.5 Sqm and n.exc 4 Sqm complete all as specified and directed. 25 S&Faluminum powder coated window and ventilator side hung type without sash, frame of weight not less than @0.75 kg/ RM bar aluminium sections weighting 0.55 kg/ m incl 4mm thick sheet glass pens/SS wire mesh necessary joining cleat, glazing clips, rubber packing, anodised aluminium snap beading, screw, anodised aluminium fittings such as peg stay 150 mm long (1 No) hinges type B-21 100 mm long(2 Nos) Suitable handle (1 No.) including aluminium powder coated grill of size 50 x 50mm,5mm thick including taking down exisiting window with frames complete all as specified and directed. 26 S&F stainless steel,butt hinge (ISI Marked) and fixed of following size complete all as specified and directed:- 27 100mm long 28 S&F anodised aluminium barrel tower bolts (ISI marked) of extruded section of following size complete all as directed and specified:- 29 150 mm long 30 S&F anodised aluminium handles cast type of following size complete all as directed and specified:- 31 150 mm long 32 S&F anodised aluminium sliding door bolt (ISI marked) with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of following size complete all as specified and directed:- 33 250mm long 34 S&F hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws of following size complete all as directed and specified :- 35 150 mm 36 S&F aluminium extruded section body door closer hydraulically regulated, designation No -3, universal type, suitable for door shutter of 851 to 1000 mm in width and of weight 61 to 80 Kg (ISI marked) complete all as specifiedand as directed. 37 S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed. 38 S&F floor doorstopper (ISI Marked) of aluminium alloy body andtongue anodised, with hard drawn steel spring, fixed in floor of following size complete all as specified and directed :- 39 140 mm long (overall length of cover plate) 40 S&F fancy type decorativeStainless steel curtain rod, 25 mm dia 1.25 mm thickincluding brackets and decorative type knobs both side of each rod, including taking down old curtain rod or pelmet boxes completeall as specified and directed.Note :- Measurement will be taken between end point of knobs. 41 S&F Dust/Snake guard aluminium strip in doors of size 40 x2 mm with rubber atbottom rail complete all as specified and directed. 42 Supply and laying of CPVC pipes 20 mm outer dia SDR 13.5 pipes and plain CPVC SDR 13.5 fittings on wall/ceiling or laying in floors complete all as specified and directed. 43 Supply and laying of CPVC pipes 25 mm outer dia SDR 13.5 pipes and plain CPVC SDR 13.5 fittings on wall/ceiling or laying in floors complete all as specified and directed. 44 M&L for cutting chases in brick wall, pinning in and making good in cement mortar (1:3) to match with existing surface for following girth complete all as specified and as directed :- 45 Cutting not exc 10cm girth. 46 Taking down chowkhats or frames with shutters ( without taking off shutters from the frames) of following size complete all as specified and directed:- 47 Area not exc 1.5 sqm each 48 Areaexc 1.5 sqm not exc 4.0 sqm each 49 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. 50 S&F CPVC 20 mm outer dia brass elbow complete all as specified and directed. 51 S&F CPVC 20 mm outer dia brassTeecomplete all as specified and directed. 52 Taking up or down 15mm diasteel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed. 53 Taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed. 54 S&F in repair gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, for following bore complete all as specified and directed:- 55 20 mm bore 56 S&F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches/floor or fixed to wall including necessary clamp of following size complete all as specified and as directed :- 57 75 mm bore 58 S&F in repair PVC (SWR) floor trap, out let dia 75mm, plain with grating including jointing with solvent cement and waste pipe complete all as specified and as directed. 59 S&F in repair PVC (SWR) vent cowl of following size complete all as specified and as directed :- 60 110 mm bore 61 S&F in repairPVC connection 15 mm size with PTMT nut of following length complete all as specified and directed :- 62 450mm 63 S&F in repair chromium plated brass shower rose fancy typewith or without swivel joints 125 mm size including shower arm complete of approvedquality complete all as specified and directed. 64 S&F in repair 15 mm bore bib taps, chromium plated, fancy type,cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. 65 S&F in repairs 15 mm borepillar taps, cast copperalloy, with capstan heads, chromium plated , Fancy type screwed down for pipe,high pressure , with or without lettered " "HOT" or "COLD" with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified and directed. 66 S&F in repair 5mm thick bevelled edge best quality looking mirror of size 600x450 mm with 30 mm PVC beading all around the glass, mounted over 3mm thick PVC sheet or 6mm thick AC bldg board, complete all as specified and directed. 67 S&F in repair chromium plated health faucet, telephonic type with CP flexible arms 1.00 mtr and hooks of approved make suitable to fix to 15 mm bore CP angle valve complete all as specified and directed. 68 S&F in repairs 15mm bore stop valve fancy type, cast copper alloy chromonium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed. 69 S&F in repair toilet paper holder of brass, chromium plated, fixed to walls with chromium plated (CP) brass screws complete all as specified and directed. 70 S&F in repair Glass shelf with Sheet Glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long.complete all as specified and directed. 71 S&F 30mm thick Moulded WPC Brown Factory made 100% Solid door (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture andback side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and directed. 72 S&F 30mm thick Factory made Wiremesh SOLID WPC(Wood Plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including S.S wire mesh shall be fixed with 15 x 15 square tube in side rails with screwing 8x28 heat metal zinc coated screws can be removed or fix again after changing of wire mesh when needed. The density of the door shall be as per manufacture instruction complete all as specified and directed. 73 S&F Factory made 100% Solid WPC Brown door Frame (125mm x 63mm Double Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed. 74 S&F Factory made 100% Solid WPC Brown door Frame (75mm x 50mm Single Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed. 75 S&F in repair vitreous china wash hand basin, white, flat back, size 550mm x 400mm excluding taps, chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets, waste pipe & CP brass waste coupling of 32mm dia complete all as specified and directed.Note : Rate quoted under this item deemed included fixing of taps, plug and chain and connecting up to supply pipes, wastes or traps etc. 76 S&F in repair vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic seat and cover, white, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti -syphonage pipe, etc., completeall as specified and directed. 77 S&F in repair PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia of make as approvrd by GE complete all as specified & directed. 78 S&F PVC water storage tank triple layer cylindrical,white colour vertical with closed top with threaded cover hoisted and fixed in position tank capacity 500 Ltr with and including ball valve high pressure of PTMT with epoxy coated aluminum rod and high density plastic ball screwed for 20mm bore of iron pipe and making connection for inlet and outlet including dismantlingof old water tank and removing from site complete all as specified and directed. 79 S&F PVC water storage tank triple layer cylindrical,white colour vertical with closed top with threaded cover hoisted and fixed in position tank capacity 1000 Ltr with and including ball valve high pressure of PTMT with epoxy coated aluminum rod and high density plastic ball screwed for 20mm bore of iron pipe and making connection for inlet and outlet including dismantling of old water tank and removing from site complete all as specified and directed. 80 M&L for preparation newly plastered or unplastered surfacesofceilingand applying two coats of oil bound distemper white or tinted over a coat of primer complete all as specified and directed. 81 M&L for preparation of old decorated surface of internal wall by removing existing treatment with mechanical sander (rpm 1500-2700)along with internal dust extraction system for clean environmentand applying two coats of acrylic distemper using roller over a layer of wall care putty to make the surface smooth all as specified and prescribed by manufacturerand all as directed at site by Engr-in-Charge.Note:- (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per manufacture’s instruction before application of distemper.The cost of materials, labour & T&P required for preparation of surface are deemed to be included in the rates quoted.(ii). All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by department for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture.(iii). After carrying out preparation of surface the same shall be got approved from GEbefore application of distemper for each building.(iv).The colour / shade will be all as approved by GE. 82 M&L for preparation of old decorated surface of exterior wall by removing existing treatment with mechanical sander (rpm 1500-2700)along with dust extraction system for clean environment , then washing the surface with Bleaching powder solution for treatment of fungal growth and applying two coats of exterior anti fungal acrylic emulsion painthaving three years of performance warranty over a coat of exterior water based primerall as specified and prescribed by manufacturer of paint and as directed at site by Engineer-in-Charge.Note:- (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacturer instruction before application of distemper.The cost of materials, labour & T&P required for preparation of surface are demand to be included in the rates quoted.(ii) All the material to be incorporated in the work shall be brought by Contractor to MES store yard which will be subsequently issued by department for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture.(iii). After carrying out preparation of surface the same shall be got approved from GE before application of distemper for each building.(iv).The colour / shade will be all as approved by GE.(v) The cost of Scaffolding wherever required are deemed to be included in the rates quoted by the contractor. 83 ditto- all as per Ser No 70 above but two coats of weather coat emulsion paint complete all as specified and directed. 84 M&L two coats of weather proof emulsion paint weather coat(having three years performance warranty) over a coat of exterior water based primeron newly plastered surfaceincluding preparation surface complete all as specified and directed. 85 M&L for twocoats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed. 86 Removal of existing roof treatment i.e. APP Membrane or brick tiling including concrete padding and benching and open up RCC roof slab including picking, sweeping cleaning with wire brush and washing down with water to remove dust, dirt to get surface free of laitance, scales, oil or any other loose material without damaging existing serviceable structure complete to receive new roof treatment including rubbish off the premises upto a distance exc 250 mtr but n.exc 500 mtr complete all as specified and directed. 87 M&L forPCC (1:2:4) Type B-0 (using 12.5mm graded stone aggregate) padding mixed withliquid water proofing compound (as per manufacturer instruction and paid separately) over and including one coat of cement slurry admixed with acrylic bonding compound SBR Latex liquid polymer as to be used for bonding of new concrete/mortar to old surface as per manufacturer instruction and finishing the surface even and smooth (without using extra cement) as in roof padding/Sunken floor, kerb/bencing alongwith parapet including rounded, chamfered on edges complete all as specified and directed. Note : Proportion of mix and method of mixing of approved concrete admixture should be applied as per manufacturer"sinstructions) 88 M&L for10mm thick screed bedding in CM (1:3) mixed with acrylic bonding compound SBR Latex liquid polymer finished the surface even and smooth without using extra cement complete all as specified and directed.(Note : Proportion should be applied as per manufacturer"sinstructions) 89 M&L of water proofing treatment to non-accessible roof slab with APP based modified polymeric membrane as per manufacturer"s instructions with following course of description below :-(i) Applying a priming one coat of bituminious primer evenly @ 0.30 Kg/Sqm till the surface is properly impregnated.(ii) Providing APP based 5 layer polymeric membrane minimum weight 3.00 Kg/Sqm and minmum 3mm thick reinforced with polyester non-woven fabric matt (weight not less than 150 gms/Sqm) centre core laid on primed surface by torced applications as per the manufacturer"s instructions with side over lap of 75mm and end overlap of 100mm. All overlap joints shall br sealed throughly by thermo fusing both the membrane layer (torching overlap by propane or butane gas torch) and sealing it with the help of hot trowel. The overlapjoints shall be made as a monolithic layer. (iii) Apply two coat of bituminous aluminium paint @ 0.20 Kg/Sqm over APP Membrance.(Note: the work in respect of water proofing treatment shall be carried out only by authorized/approved applicator of the manufacturer/firms of APP membrane. The contractor shall submitted 10 year company back warranty before claiming payments complete all as specified and directed. 90 Cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc to store and rubbish not exc. 50m complete all as specified and directed. 91 M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 92 M&L for mild steel TMT bars 5 to 10mm dia bars as in stirrups cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 93 Demolition of RCC in Roofs, floors ( other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforced) including cutting of reinforcement to facilitate demolition complete all as specified and directed. Note : Reinforcement obtained from demolition will be considered credit Sch as scrap iron. 94 M&L for precast RCC (1:2:4) type B1, (using 20mm graded stone aggregates) as in cover slab (for manholes) , chullahhoods,chajjas, water troughs,mangers, shelvesand similar articleswith plain faces and set in CM (1:6) including necessary fair finish formwork complete all as specified and directed. 95 S&F rolled mild steel section for Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, conforming to Fe-410-W(Gde-E-250) quality-A etc complete all as specified and directed. 96 S&F in repair fancy type Vitreous china white wash down couple closet composite type including PVC soft seat cover and flushing cistern (single pattern) white completeof approved quality complete all as specified and directed. 97 S&F in repairs 18 mm thick prelaminated PVC celuka Ply prelaminated one side with decorative choice lamination and other side plain fixed with screw to PVC celuka ply works, complete all as specified and as directed. 98 S&F in repair 18mm thick WPC boardand bothside plain white colour as in cup board shutters and frames, kitchen cabinet front shutter, partiton, shelf & drawer, fixed with screws, solvent cement/ adhesive complete all as specified and directed. 99 S&F in repair stainless steel sink with out draining board, made out of 1.00 mm thick sheet for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever brackets, connecting union overall size 495mmx420mm with bowl size 410mmx 330mmx160mm complete all as specified and directed. 100 S&F 0.90 mm thick decorative laminate type 1, of surface finish, colour and pattern as approved , fixed with approved adhesive as per GE instructions, complete all as specified and as directed. 101 S&F set of 6 modular kitchen stainless steel basket, pull out drawers, shelves cabinet, rack basket tray, Dish plate rack (set of 2) with tray for multipurpose utensils container shelf organizer complete including all fittings complete all as specified and directed. 102 S&F in repair 15mm dia fancy type brass CP wallmixture (hot & cold) with swinging spout (wall mounted model) with connecting legs and wall flanges screwed down for iron pipe and fixed complete of approved quality complete all as specified and directed. 103 S&F in repair 15mm Brass CP fancy typewash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixedcomplete of approved quality complete all as specified and directed. 104 S&F in repair Hydraulic Self Closing hinges 35mm of crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position complete all as specified and directed. 105 S&F D-type cabinet handles fancy type premium quality, stainless steel 304/gloss chrome/SN finished 100mm long matt finished complete of approved quality complete fixed in position all as specified and directed. 106 S&F D-type cabinet handles fancy typepremium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete of approved quality complete fixed in position all as specified and directed. 107 S&F Ball Catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer"s instruction complete all as specified and directed. 108 M&L for coloured vitrified tiles of any design and pattern, double charged, 9 to10 mm thick, as in floor etc incl 15 mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B1b with average water absorption less than 0.05%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 4.0% (Max deviation). Centre & Edge curvature and warpage + 0.20% (Max Deviation). Breaking strength 1200 N (Minimum) and minimum 95% tiles shall be free from visible defects and area of each is as following complete all as specified and directed :-Note: Shade of the tiles including Colour, design and pattern shall be got approved by GE/ AGE(I). 109 Area of each tilen exc 0.36 sqm 110 Description same all as per item No.96 but in riser of steps, skirting, dado and pillaretc with and includind over 10mm thick rendering in CM (1:4) complete all as specified and directed. 111 M&L for non skid, joint free, coloured ceramic tiles7-8 mm thick (Square/Rectunglar), as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles laid with and including over 15mm thick screed bed in CM (1:6), area of each tiles shall be of following complete all as specified and directed :- 112 Area of each tilenot exc 0.11 Sqm. 113 S&F in repair 20 mm dia brass CP fancy type tubular towel rail D type 600 mm long as approved complete all as specified and directed. 114 M&L Cement concrete Type B2 (1:2:4) using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed. 115 Dismantling and taking down U/S copper / aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified and directed.Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding. 116 Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc.complete all as specified Note:- Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates( ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding. If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding. 117 M&L for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with contineous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealedPVC conduit ,duly concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia(Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover cover plate complete all as specified and directed. Note:-Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates 118 One 3pin/5pin 5/6 Amps socket out let on same boardwith other switches ,with cables 1.5 sq mm size , complete all as specified and directed. 119 One 3pin/5pin 5/6 Amps socket out let onindependent board with other switches, with cables 1.5 sq mm size,complete all as specified and directed . 120 All as per item No 103 abovebut with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point complete all as specified and directed. 121 S & F Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC omplete all as specified and directed. 122 Supply and fixing switch modular , one-way 16Amps,1 module 240 Volts AC omplete all as specified and directed .. 123 Supply and fixing modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz omplete all as specified and directed .. 124 Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed by Engr- in-charge. 125 Supply and fixing bell pushmodular flush type single pole one way 6 Amps, 1 module all as specified and directed. 126 S&FBell ding dong Type , 240 Voltscomplete all as specified and directed. 127 Supply and fixing ceiling rose surface bakelite 65x25mm dia having three terminals ISI marked all as specified 128 Supply and fixings modular fan regulator 120/280 V , Suitable for BLDC ceiling fan complete all as specified. 129 Supply and fixing batton/angle holder insulated body with back plate, suitable for batten fittingsall as specified & directed. 130 Supply and fixingLED lights fitting 1X20 watt ,4 ftwith extruded aluminium housing heat sink, environmental friendlyenergyefficienttranslucent diffuser with LED light source,2400 Lumens( minimum)coefficient colour temp 6000°K to 6500 °K, surge protection range ≥ 2.5KV, voltage protection range-120-300VAC,2 years warranty ,system efficacy not less than140Lm/Watt for the fitting, power factor >.95,total harmonic distortion< 20% color rendering index>80, fixed on site with all accessoriesincluding connecting up with three core flexible copper conductor cable of suitable size from ceiling rose all as specified & directed. 131 Supply and fixingenergy efficientLED lights fitting, 9 watt , 230 Volt, of 600 mm length,CCT 6000ºKto 6500° K , decorative ultra slim linear LED lighting fixture with extruded aluminium housing heat sink, environmental friendly, energy efficient LED light source more than1200 lumens , wall mounted mirror batten, integrated electronic driver, system efficacy not less than 140 lumens /watt CCT 6000to 6500°K , surge protection range ≥ 2.5 KV , voltage protection range 120-300 volt AC, power factor > 0.95 total harmonic distortion< 20%, colour rendering index > 80, fixed on site with all accessories including 2 years warranty connecting up with three coreflexible copper conductor cable of suitable size from ceiling rose complete all as specified& as directed.. 132 S&F LED wall mounted decorative luminaire suitable for LED lamp 9 /12watt B-22 base holder and LED lamp complete all as specified and directed. 133 S&F round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. 134 Supply and fixing single pole and neutral enclosure with a two pole and earth plug socket complete with 01 No, RCCB 20 Amp, , 240 Volts,AC Complete all as specified.(Note - Cost of cutting chases for enclosure concealed in wall of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates complete all as specified and directed. 135 S & F wall fan 400mm sweep 240 volts Ac 50 Hzccomplete all as specified and directed. 136 S & F ceiling fanBLDC Type 1200 mm sweep 240 volts Ac 50 Hz, with remote controlcomplete all as specified and directed. 137 S & F exhaust fan 240 volts Ac 50 Hz 300 mm sweep matellic body (RPM will not be more then 900) including louvers and cutting as required size and shape complete all as specified and directed. 138 S & F electric water heater storeage type geyser (ISI marked ) 5 star rated inner stainless steel 2 KW of capacity 25 Ltr complete grouting wall with suitable size of nut & bolts washer as required at site with cold water and hot water connection pipe as per required at site,complete all as specified and directed. 139 S & F electric water heater storeage type geyser (ISI marked ) 5 star rated inner stainless steel 3 KW of capacity 5 Ltr complete grouting wall with suitable size of nut & bolts washer as required at site with cold water and hot water connection pipe as per required at site,complete all as specified and directed. 140 S & F PVC fresh airfan 240 volts Ac 50 Hz 250 mm sweep PVC body including louvers and cutting as required size and shape complete all as specified and directed. 141 Supply and fixingLED building security light 1X30 W housing made out of pressure die-cast aluminium alloy with toughened glass, IP-66 protection, working on 240 Volts , 50 HZ, consisting of reflective lens wired with appropriate driver PF>0.98 having over voltage protection up to 440 volts, Surge protection level ≥ 10 KV, thermal short circuit protection THD < 10% made up of long life LED chips (SMD) in modular with Ra>70, and LED lumen efficiency >140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminior efficiency > 130 Lumens/watt, power LED should be of more than 01 wattCCT should be between 5700° K- 6500° Kincluding fixed onwall with 02 Nos MS clamp made out of 40X6 mm FI and bracket made out of 32 mm dia light grade GI pipe not less than 0.90 mtr long bend to shape completeallas Specifiedand directedincluding connecting with 1.5 sq mm, 3 core, PVC insulated Copper conductor cable 1100 Volts grade from terminalbox to light fittingscomplete all as specified and as directed by Engr-in-Charge (i)the firm has to give warranty for street light fittings including driver minimum for 03 years for any defects developed during the period. (ii) The contractor shall submit the third party LM 79 report from any NABL approved laboratory. (iii)The fitting should have BIS, CRSno Make Shakti/Havells/Crompton. 142 Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 8 way with 200 Amps rated bus bar complete all as specified and directed. 143 Supply and fixing MCB SP 5 to 32 Amp "B" series 10 KA repturingcapacity complete all as specified and directed. 144 Supply and fixing MCBSPN40 Amp 240 V AC 10 KA repturingcapacitycomplete all as specified and directed. 145 Supply and fixing in repair sub main wiring two single core 4 sq mm PVC insulated unsheathed multi stranded copper conductor cable ( FRLSH ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade surface/ concealed in wall as per existing along with 4.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLSH ) as earth wire and wire connected withmain earth dolly including cutting chasing and making good disturbed portionall as specified and as directedNote:- Two runs of multi stranded copper conductor cableand one run of earth wire including PVC conduit will be measured as a one length. 146 M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground, earth pit not less than 2.25 mtr depth below ground level at any type of strata with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate, connected by 4 mm GI wire as earth lead by means of brass nuts and bolt, thimbles check nuts, washers including concrete chamber of PCC (1:3:6) type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM (1:4) funnel with wire mesh, RCC pit cover of 320 x 320 x 80mm size PCC (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion complete all as specified and directed.

Contact Information