|
Tender For Special Repair To Building No Np45 And Np47 At Hq Northern Command Camp Under Ge South Udhampur; 1 Excavation in trenches n.exc. 1.5 m wide and n.exc. 1.5 m in depth for foundation or manholes etc, and area n.exc 10 Sqm on plan and getting out in any typesoil complete all as specified and as directed. 2 Returning, filling in with approved soil obtained from excavation including spreading levelling, watering and well ramming in layers n.exc. 25cm thick omplete all as specified and as directed. 3 Removing excavated soil to a distanceexc 50m and nexc1.50 km out side defence land complete all as specified and as directed. 4 Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each and removing to store complete all as specified and as directed. 5 Taking down chowkats or frames with shutters (without taking off shutters from the frames)exc 1.5 sqm but n.exc 4 sqm each and removing complete all as specified and as directed. 6 Taking down cement plaster of any description on brick/stone walls or concrete surfaces including racking out joints, hacking for key scrubbing down with water etc on walls and ceiling, complete all as specified and directed. 7 Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed. 8 Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and as directed. 9 Dismantling structural steel work including doors, gates including framed truss etc complete all as specified and as directed. 10 Dismantling timber scantlings 40 sq. cm and over in section, in any position and in un framed work complete all as specified and as directed. 11 Dismantling wall & ceiling boards of any description and thickness including cover fillets, complete all as specified and directed. 12 Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed. 13 Demolition cement concrete in ground floors and paving ( unreinforced ) n exc. 15 cm thickness (below or above ground floor) complete all as specified and as directed. 14 M&L for brick work with sub class B bricks exc 6m mean radius straight or curved on plan built in cement mortar1:6including complete all as specified and as directed. 15 M&L for walling of randomrubble masonary, Squre, recangular coursed, well bonded, bedded and solidly hearted, built in CM (1:6) complete all as specified and as directed. 16 M&L for raised pointing to random or polygonal rubble masonary coursed or un coursed inCM (1:3) complete all as specified and as directed. 17 M & L for brick work with sub class B bricks straight or curved on plan exc 6 mtr mean radius built in CM (1:4) as in manholes, septic tank, filter bed, walls, drains etc complete all as specified and as directed. 18 M&L for plain cement concrete1:2:4 type B-2 using 40 mm graded stone aggregate as in channels and drains, foundation and similar work etc complete all as specified and as directed. 19 M&L PCC 1:2:4type B0 (12.5mm graded aggregate) as incoping, benching and similar work etc including necessary form work complete all as spcified and directed. 20 M&L for cement concrete type B1 1:2:4 (using 20 mm graded aggregate) use incoping, hold fast and similar workincluding necessary form work complete all as specified and directed. 21 M&L Cement concrete type D 2 (1:4:8) (using 40mm graded stone aggregate) as in foundation filling and mass concerete complete all as specified and as directed. 22 M&L for 75mm thick PCC 1:3:6, type C-2by using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed. 23 M&L for 75 mm thick plain cement concretetype D-2 (1:4:8) (40 mm graded stone aggregates) as in sub basecomplete all as specified and directed. 24 M & L for RCC 1:2:4 type B1 using 12.5mm graded aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. 25 M&L for SWG drain pipe grade A of150 mm internal dia laid in trenches and jointedin cement mortar (1:1) complete all as specified and as directed. 26 M&L Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concretetype D2 (1:4:8) for 150mm dia pipe complete all as specified and as directed. 27 M&L for Reinforced cocrete pipe300 mm dia,class NP-2 laid to floorandwalljointed complete with collars complete all as specified and as directed. 28 M&L for concrete bed to drain pipes 300 mm dia type 1:3:6 C-2 including paking under,and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed. 29 M & L for providing cement concrete 1:2:4 Type B1 using 20mm graded aggregate as in lintels up to 1.5m clear span, cills,seismic and other similar bands, plinth courses, copings, Bed blocks, and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed. 30 Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. 31 M&L Precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate ) for manhole cover septic tank covers slabs etc including necessary form work and set in CM (1:4). (Note:- reinforcement will be measured and paid seperately.) 32 M&L for chequered cement concrete (glossy finish) tile 300 mm x 300 mm x 25 mm thick setjointed andpointed in neat cement slurry in floor with grey cement and pigment all as specified and directed. 33 M&L For TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for colunms, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 34 M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to IS complete all as specified and as directed. 35 S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. 36 S&F PVC bend 110 mm dia any radious with acess door complete all as specified and as directed. 37 S&F 110mm bore (SWR) vent cowl complete all as specified and as directed. 38 M & L Rendering 15 mm thick on brick or concrete surfaces of walls in CM (1:4) including finishing the surfaces fair and even without using extra cement all as directed 39 M & L Rendering 10 mm thick on brick or concrete surfaces of walls in CM (1:6) including finishing the surfaces fair and even without using extra cement all as directed 40 M & L forflat formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete complete all as specified and as directed 41 S&F Pre-Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed. 42 S&F Pre-Painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed. 43 M & L for applying 1 mm thick layer of wall putty on walls to give uniform surface, surface scrubbed with emery paper and make surface good and clean complete all as specified and directed. 44 M&Lfor applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed. 45 M & L for preparation of new plaster surfaces of walls/ceiling and applying two coats of oil emulsion distemper (white/tinted) all as specified and as directed. 46 S&F 10-12 mm thick gypsum boards seamless false ceiling including sunk or raised moulding or cop design as approved, moisture resistant, including GI hanging wires & frames with intermediate, perimeter channel ceiling channel, along nuts and bolts connecting plates gypsum boards, dry wall screws soffits cleats, ceiling section, rawel plugs fixtures and screws and applying two coats of emulsion paint over a coat primer on exposed surface complete all as specified and directed.Note : (a) Design of ceiling board as approved by Engr-in-Charge. (b) GI grid/hanging system shall be of the same make as of false ceiling manufacturer complete all as specified and as directed. 47 S&F Vitrified Dura stone pathway tiles of size not exc 0.36 Sqm of 15mm thick as in floors and over & including 15mm thick screed bed or bedding layer in cement mortar 1:4, including jointed with neat cement slurry and pointed in coloured cement to match the surface of tiles, complete all as specified and directed 48 M&L for vitrified tiles (double charge glossy finish), area of each tile exc 0.42sqm but not exc 1.00 Sqm, 8-10mm thick (square or rectangular) of superior quality as in floor surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. 49 M&L for vitrified (double charge glossy finish), area of each tile exc 0.42sqm but not exc 1.00 Sqm, 8-10mm thick (square or rectangular) as in skirting/dado of wall surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles and including 10mm thick renderingin CM 1:4 complete all as specified and directed. 50 M & L for non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed. 51 M & L for Glazed Coloured Ceramic tiles in vertical surface300x600x7mm thick or 600x1200x7mm thick laid over 10 mm thick rendering/backing coatin CM 1:4, set and joint in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed. 52 M&L for coloured chequered cement concrete tiles 30cmx30cmx2.5cm ,machine pressed; set jointed and pointed in neat cement slurry in floors, with grey cement and pigments laid over 15 mm thick screed be in CM 1:6 complete all as specified and as directed. 53 M & L 18-20 mm thick granite (of any type) work( table rubbed and polished) in steps, jambs, pillars, window sills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab complete all as specified and as directed. 54 Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 55 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). Make : Eco cell or equivalent make 56 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type wire mesh solid door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). Make : Eco cell or equivalent make 57 Providing and fixing factory made uPVC white/coloured sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) 58 Supply and fixing factory made uPVC white/coloured fixed glazed window/ventilator/Partition walls made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). 59 M & L forsheet glass 5mm thick of one side view (etching design as per direction of Engr in Charge), ordinary quality and glazing with beads fixed with metal panel pins, EPDM washers or connected accessories exc 0.5 sqm in each pane complete all as specified and as directed 60 S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. 61 S&F for Stainless steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed. 62 S & F 150mm long stainless steel, anodized, barrel tower bolts of extruded section complete all as specified and as directed. 63 S&F butt hinge 100mm size, medium weight, stainless steel complete all as specified and as directed. 64 S & F 150mm stainless steel pressed handles, oval type complete all as specified and as directed. 65 S & F 150mm double action spring hinges, mild steel with steel wire spring, stove enamelled, black complete all as specified and as directed. 66 M&L for cupboard/almirah/kitchen cupboard in required size at site made out 18 mm thick one side decorative lamination sheet/sunmica consisting of carcass 18/20 mm thick PVC sheet & provn of shutters made out of 18mm thick one side decorative laminated PVC sheet all required brackets SS screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish, necessary drawer, openable shelve with frame work complete as per make and specification mention as per drawingwith locking arrangement approved by Engr-in-Charge (Make: Rajshree/Sintex/Action Tessa or equivalent) Complete all as directed. 67 S&FPVC steel catcherof superior quality all as specified and directed by Engr in charge 68 Supply only Stainless steel basket (plain), SS plate basket(11-13 division), SS partition basket, SS Cutlery basket,SS grid basket of size as per manufacturer/ as directed by Engr in Charge made of 4mm the S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18/20 length two wayextruded MS galvanised over rollers of approved make Make: Life style Cat part No WA/POB/15204 or equivalent approved 69 S & F Hettich soft closer hinges of stainless steel premium quality complete all as specified and as directed. 70 S&F Fancy type Brass handles 100mm size fixed with screws, complete all as specified and as directed. 71 S & F 30 mm width of flap Continuous (Piano) hinges, mild steel, bright finish orelectro galvanised complete all as specified and as directed. 72 S&F in repair Sinks with draining board made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastesincluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x460mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed. 73 S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways;railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and as directed. 74 M&L for rolled section as in main and cross beams, purlins, rafters, posts where connected to common rafter and running rails, frame work of eves board, tank staging work etc conforming to Fe- 410-W complete all as specified and as directed. 75 S&F 4 mm dia galvanised steel wire 150 mm x 100 mm mesh made up in to mattresses or cages etcall as specified and as directed. 76 S&F 20mm dia stainless steel powder coatedfancy type tubular curtain rail with brackets and end bulb as per requirement. all as directed. 77 S & F in repair 15mm bore bib tap of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed. 78 S & F in repair 15mm bore stop valve/angle cock, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed. 79 S&F inrepair15 mm dia WHB/wall/sink mixerchromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and as directed.Make - Jaquar Cat No KUP-35011BPMor equivalent in Hindware/Cera/Parryware 80 S&F in repairs 5 mm thick looking mirrorof required size, fixed on walls with dash fasteners and chromium plated screws purposefully made to fix the glass by drilling hole in the glasscomplete all as directed. 81 S&F in repair Soap dish holder incl all fittings complete all as specified and as directed. 82 S&F in repair counter top vitreous chinawarewash hand basin (WHB) whitesize 550mm x 400mm complete including 32 mm dia chromium plated waste coupling, PVC waste pipe and cutting for pinning in ends of brackets in wall etc complete. Make : Jaquar Make :KUS-WHT-35601 or its equivalent in Hindware/Cera/Parryware 83 S & F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed. 84 S&F in repair water closet single piece/wall hanged pattern coloured of size 535 x 380 x 400 mm in repair as approved and complete all as specified and directed. Make : Jaquar Cat part No KUS-WHT-35851S300UF or equivalent in Hindware/Cera/Parryware. 85 S&F 200 mm dia brass chromium plated shower rose with swivel joints in repair complete all as specified and directed. 86 S&F Health faucet ABS body with wall hook and 1 mtr chrome plated PVC hose pipe in repair complete all as specified and directed. Make : Jaquarand equivalent . 87 S&F in repair towel rack complete all as specified and directed. Make : Jaquar Cat Part No ACN 1181FN and equivalent in CERA/ Parryware. 88 S&F PVC connection 15 mm dia and 600mm long with two Nosof brass check nuts and washers complete all as specified and as directed. 89 S & F 15mm steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls including taking down old pipe complete all as specified and as directed. 90 S & F 20mm steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls including taking down old pipe complete all as specified and as directed. 91 S & F 25mm bore steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls,15mm bore including taking down old pipe complete all as specified and as directed. 92 M & L for 1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I and PTMT ball valve 20mm dia including taking down of old tankand removing from site complete all as specified and as directed. 93 S & F in repair of gun metal gate valve, painted finish, with forged brass spindle and iron wheel head, screwed both endsfor iron pipe of size 20mm bore complete all as specified and as directed. 94 S&F PVC (SWR) Floortrap, 75 mm dia of outlet, plain with grating including jointing with solvent cement and making good all as directed 95 S&F600 mm long tubular tower rail brass chromium plated 20mm dia, D type 60cm long fixed with two plugs (Gutties) of 2nd class hard wood embedded in cement mortar 1:3 with MS screws complete all as specified and as directed. 96 M&L for preparation of newly steeland iron surfacesexceeding 10 cms width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed. 97 Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power) complete includingfitting such as switch, sockets, ceiling rose, pendants socket,fan regulators any type, rectangular board ,light fittings,terminal boxes etc removing materialsfor taking credit and making good disturbed surfaces of walls floors and ceiling complete all as directed. 98 Taking down main switches, distribution boards and cut outs etc. of any type and capacity along with the existing boards and removing the same from site and making good the disturbed surface/portion of walls complete all as specified and directed By Engr-in-Charge. 99 Point wiring for one light/ fan/bell point controlled by oneswitch using 1.5 Sq mm FRLSH copper conductor cables (multistranded) PVC insulated and unsheathed in and including PVC concealed conduit pipe as per site requirement (size not less than 20mm dia), medium grade with Modular sunken boxes & PVC/metal back plate for mounting modular type switches, sockets & regulators etc with cover plate modular type including supplying and laying PVC insulated and stranded unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire connected to earth dolly includingcutting of chases in wall /ceiling etc and making good the disturbed surfaces match to existing with cement mortar and putty white /colour wash complete all as directed . Make: Havells/ Finolex/ Polycab. 100 All as per item no 99 above but cable 2.5 sqmm FRLSHfor one 3/5 pin 6 Amp socket outlet point on an independent board. 101 All as per item no 99 above but cable 2.5 sqmm FRLSH for one 3/5 pin 6 Amp socket outlet point on the same board with other switch. 102 All as per item no 99 above but for one bell/buzzer pointcontrolled by one bell push single pole one way . 103 All as per item no 99 above but for Two way point control by Two two way 6 Amp switch. 104 All as per item no 99 above but for one 3/6 pin 16 amps socket outlet point on an independent board with cables of size 2.50 sqmm. 105 All as per item no 99 above but an independent board with cables of size 4.0sqmm. 106 S&F for modular switch6 Amps single pole one way230 V, 50 Hz, AC , with outer cover complete all as specified and directed by Engr In charge. Make:Legrand/Havell crabtree/L &T 107 S&F Switch modular, flush type, single pole, Two way 5/6 Amp 230 Volts complete all as specified and directed. Make:Legrand/Havell crabtree/L &T 108 S&Fmodular bell push, flush type, single pole, one way 5/6 Amp 230 volts complete all as specified and directed.Make:Legrand/Havell crabtree/L &T 109 S&F for modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC , with outer/inner covercomplete all as specified and directed by Engr In charge. Make:Legrand/Havell crabtree/L &T 110 S&F for modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with outer cover complete all as specified and directed by Engr In charge. Make:Legrand/Havell crabtree/L &T 111 S&F for modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush typewith outer/inner covercomplete all as specified and directed by Engr In charge. Make:Legrand/Havell crabtree/L &T 112 S&F Lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. 113 S&F LED retrofitlamp of capacity 12 watt, B-22 holder base with polycabonate body and aluminium heat sink warm white/day light complete all as specified and directed. 114 S&F in replacement ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed. 115 S&F in replacement electric bell ding dong type AC 230 Volts, 50 Hz single pole complete all as specified and directed. 116 S&F in replacement electronic step type fan regulator 100 watt 230 volts 50Hz two module C/S deluxe type complete all as specified and directed. Make: Havells Crabtree/ Legrand/ Indoasian. 117 S&F in replacement sheet metal enclosure for MCB DB double door type, single pole and neutral 12 way 240Volts with 200 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed. 118 Supply and fixing in replacement 240V, 10KA C curve miniature circuit breaker (MCB) of TPN 63 Amp current carrying capacity in the MCB DB complete with connection testing and commissioning. 119 S&F in replacement MCB Single Pole, 6 to 32 Amps 240 volts, 10KA breaking capacity, convenient to C Curve complete all as specified and directed. 120 Supply and fixing in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. Make-Havells LED Pride Plus Neo Batten 10 W Cat Part No LHEXACP7IN1W010 or Equivalent make in Bajaj/C&S 121 S & F in repair LED light fitting 1x9W/10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. Make- Wipro / Bajaj /Philips 122 S& F in replacement LED tube light fittings of 20 wattageincluding rawl/plug ,making connection with and including 23/0 0076 flexible copper wire three core from connector to ceiling rose not more than 1.2 mtr fixed to wall firmly , complete all as specified and directed. 123 S & F Modular TV Socket outlet single with inner and outer cover required module including TV cable required length from roof complete all as specified and directed by Engr-in-charge Make-Havells/Legrand 124 S & Fin repairs LED decorative down light fitting/recess mounted roundtype white/ warm white with high out put diffuser 8/12/15 watt 220 V AC with driver holder and LED lamp including connecting up withflexible copper conductor cable of suitable size complete all as specified. Make: Philips /Bajaj/Havells 125 S & Fin repairs LED paneldecorative down light fitting/recess mounted square type white/ warm white 2X2 36W with high out put diffuser220 V AC with driver holder and LED lamp including connecting up withflexible copper conductor cable of suitable size complete all as specified. Make: Philips /Bajaj/Havells 126 S&F Decorative wall light ?xture made up of Polycarbonate, suitable for 15W retro?t LED bulb (B-22 base) polycarbonate body, weather proof, LED light fitting fixture with co extruded polycarbonate body,environmental friendly, energy ef?cientcomplete with all accessories, prewired and making connection with and including three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp complete all as specified and directed. Make- Havells / Philips / Crompton greaves. 127 S&F in replacement 25 Wattlighting luminaire with unique peanut optics to ensure uniform distribution, higher spacing between poles and maintenance free system for city roads and Streets, 50% Energy Savings, IP66 Protection PC and FG Cover, High Impact Resistance complete including LED Lamps and all accessories including bracket made out of 25mm bore GI pipe (light grade), 1.20 m long made to shape and fixed to existing pole or bldg by means of 2 Nos mild steel flat iron 40x6mm clamps with suitable size bolt, nuts & washers and connecting with three core flexible copper wire of size 23/0.0076 from ceiling rose to existing junction box complete all as specified and directed. Make Philips/ Havells/ Bajaj/ Crompton greaves. 128 M & L for Earthing complete with galvanized steel earth plate electrodes 600 mmx600 mm x6.3 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including galvanized steel earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel including PCC pit in PCC 1:2:4 type B-1using 20 mm graded crushed stone aggregate, RCC framewith 40mm thick RCC cover reinforced with 8mm dia deformed barshandle. including excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 15mm bore main board complete all as shown in electrical plate No 5connected to main control board all as specified and testingon completion. Note: Excavation earthwork charcoal PCC pit is covered under this item including taking out existing earth plate etc If earth resistance of earthing is not found (2 to 5 O) satisfactory earthing shall be redone by the contractor. 129 S&F MCB SPN,32 to 40 Amps 240 volts, 10KA breaking capacity, convenient to C Curve complete all as specified and directed. 130 S&F in replacement sheet metal enclosure for MCB TPN DB double door type, 4 way 240 Volts with suitable rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed. 131 Supply and fix electric water heater, storage type plastic body with stailness steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. 132 Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE.Five star rated with brushless direct current motor (BLDC) 133 Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm all as directed and specified. 134 Supply, laying and testing (in replacement) of cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size10 sq mm 4 core complete all as specified and as directed. 135 M&L for sand cushioning with dry local sand for cable protecting under ground cable (8 cm before laying the cable and 15 cm after laying the cable) in trenches including punning the sand upto 18 cm thick and consolidated complete all as specified and directed. Note :Punned thickness18 cm shall be measured only. 136 Supply and laying dry well burnt locally available brick sub class B modular bricks laid flat with width equal to the length of whole bricks over cable as cable protection complete all as specified and directed. 137 S &F for 40 mm dia GI pipe light grade ISI marked including fittings such as bends, tees, sockets etc fixed on wall/pole or laid in trenches under road crossing/hard standingincluding taking down old /unserveciable existing pipe complete all as specified and directed.NOTE :Excavation and earth work shall be measured & paid separately.
|
