|
Tender For Providing And Laying App (Atactic Polypropylene Polymer) Modified Prefabricated Five Layer 3Mm Thick Water Proofing Membrane, Black Finished Reinforced With Non-Woven Polyester Matt Consisting Of A Coat Of Bitumen Primer For Bitumen Membran @ 0.40 Itr/Sq.Mt. By The Same Membrane Manufacture Of Density At 25°C, 0.87-0.89 Kg/Ltr And Viscosity 70-160 Cps. Over The Primer Coat The Layer Of Membrane Shall Be Laid Using Butane Torch And Sealing All Joints Etc., And Preparing The Surface Complete. The Vital Physical And Chemical Parameters Of The Membrane Shall Be As Under Joint Strength In Longitudinal And Transverse Direction At 23°C As 650/450N/5Cm. Tear Strength In Longitudinal And Transverse Direction As 300/250N. Softening Point Of Membrane Not Less Than 150°C. Cold Flexibility Shall Be Upto -2°C When Tested In Accordance With Astm, D-5147. The Laying Of Membrane Shall Be Got Done Through The Authorized Applicator Of The Manufacturer Of Membrane. 3 Mm Thick , Providing & Laying Broken Glazed Titles On Roof ( Broken Glazed Tiles Not Less Than 9 Kg/Sqm) On Top Of Hot Bitumen @ 1.7 Kg/Sqm. (1.40 Kg Of Vg-40 (30/40 )Grade And 0.30 Kg/Sqm. Of Vg-10 (80/100) Grade) And Joints Filled With Cement Mortar 1 :2 (1 Cement:2 Marble Dust Mixed With Water Proofing Compund All Complete As Per Direction Of Engineer-In-Charge. , Providing And Applying Acrylic Emulsion Polymer Waterproofing Chemical Coating, On Over Roof On Over Roof Slabs/Terrace/Balconies/Parapet Wall Etc.With Following Method/Specification: Paint The Surface With Regular Paint Brush So As To Obtain Approximately 0.3Mm Thickness Coating. Apply The 2Nd Coat Next Day At Right Angles To The 1St Coat So That Total Thickness Of The Coating Should Be Approximately 0.6Mm Coverage By Using Above Formulation Will Be 40 Ft2/ Litre Of Chemical. Painted Surface Does Not Require Any External Water Curing Since Chemical Will Hold Sufficient Water For Curing.After The Primer Coat Apply 2 Coats Of Modified Acrylic Emulsion Polymer Water Proofing Compound Having Solar Heat Reduction Properties Coating @ 0.330 Kg/Sqm On The Surface Of The Interval Of 3-4 Hours. Undulation On The Surface Is Repair Before The Waterproofing Work. , Providing And Fixing Steel Gate, Grating , And Grills Made Of Angles, Tees, Square Bars, Flats,Or Black Pipe With Holdfast And Fittings Complete As Per Design And Drawing Including Cutting Welding And Fabrication With Priming Coat Of Red Oxide , Providing Corrugated G.S. Sheet Roofing Including Vertical / Curved Surface Fixed With Polymer Coated J Or L Hooks, Bolts And Nuts 8 Mm Diameter With Bitumen And G.I. Limpet Washers Or With G.I. Limpet Washers Filled With White Lead And Including A Coat Of Approved Steel Primer And Two Coats Of Approved Paint On Overlapping Of Sheets Complete (Upto Any Pitch In Horizontal/ Vertical Or Curved Surfaces) Excluding The Cost Of Purlins, Rafters And Trusses And Including Cutting To Size And Shape Whenever Required. 1.00 Mm Thick With Zinc Coating Not Less Than 275 Gm/M2 , P & F 1St Quality Heavy Duty Vitrified Glazed Mat Tiles On Floor, Skirting And Steps Etc.In Different Sizes (Thickness Minimum 10Mm) With Water Absortion Less Than Or Equal 0.08% And Conforming To Is 15622 Of Approved Make In All Colour And Shade, Laid With 20 Mm Thick Cm 1: 4 Including Grounting The Joints With White Cement And Matching Pigment Etc Complete. Size 600 Mm X 1200Mm , Providing And Fixing 1St Quality Standard White, Grey, Ivory, Fume Red Brown, Light Green, Light Blue And Other Light Shades Ceramic Glazed Vitrified Tiles With Water Absortion Less Than Or Equal To 0.08% Confirming To Is:13753 & Is : 15622 On Walls, Pillars Etc. Laid On A Bed Of Neat Cement Slurry Finished With Flush Pointing In The White Cement Mixed With Pigment To Match The Shade Of The Tile Complete (Excluding The Cost Of Cement Plaster On Walls And Pillar). Size 600Mm X 1200Mm , Painting With Synthetic Enamel Paint Of Approved Brand And Manufacture To Give An Even Shade : Two Or More Coats On New Work , P & F Wvc Wash Basin (Ist Quality Is:2556 Mark) Of Approved Make With C.I. Brackets Duly Painted 1 No. 15 Mm C.P. Pillar Cock (Is:8934 Mark) & 32 Mm C.P. Brass Waste Coupling Of Approved Make, P.V.C Waste Pipe With Pvc Nut 32 Mm Complete Including Cutting & Making Good The Wall : Size 400 Mm X 400 Mm Or 450 Mm X 390 Mm Corner , Providing & Fixing Premium Quality White Glazed Vitreous China Sanitary Wares (Is:2556 Mark) Of Approved Make As Per Direction Of Engineer-In-Charge Including Cutting And Making Good The Wall And Floor. Wall Mounting European Type W.C. , P & F Premium Quality Low Level Flushing Cistern Of 10 Litres Capacity (Is:2556 Mark) Of Approved Make As Per Engineer-In-Charge With Complete Fittings C.I. Brackets Duly Painted, Brass Ball Cock With Ball, (Is:1703 Mark) Complete Including Cutting And Making Good The Wall : , Providing And Fixing Premium Quality Two Way Bib Cock 15Mm With Wall Flange Complete As Per Sample Approved By Engineer In Charge , Providing And Fixing To Existing Door Frames. 30Mm Thick Factory Made Solid Panel Pvc Door Shutter Consisting Of Frame Made Out Of M.S. Tubes Of 19 Gauge Thickness And Size Of 19Mm X 19Mm For Stiles And 15 Mm X15mm , Top & Bottom Rails. M.S .Frame Shall Have A Coat Of Steel Primers Of Approved Make And Manufacture M.S. Frame Covered With 5Mm Thick Heat Moulded Pvc ‘C Channel Of Size 30Mm Thickness, 70Mm Width Out Of Which 50Mm Shall Be Flat And 20Mm Shall Be Tapered In 45 Degree Angle On Either Side Forming Stiles; And 5Mm Thick, 95Mm Wide Pvc Sheet Out Of Which 75 Mm Shall Be Flat And 20Mm Shall Be Tapered In 45 Degree On The Inner Side To Form Top And Bottom Rail And 115Mm Wide Pvc Sheet Out Of Which 75 Mm Shall Be Flat And 20Mm Shall Be Tapered On Both Sides To Form Lock Rail. Top Bottom And Lock Rails Shall Be Provided Either Side Of The Panel. 10Mm (5Mm X 2) Thick, 20Mm Wide Cross Pvc Sheet Shall Be Provided As Gap Insert For Top Rail & Bottom Rail. Panelling Of 5Mm Thick Pvc Sheet To Be Fitted In The M.S. Frame Welded/ Sealed To The Stiles & Rails With 7Mm (5Mm +2Mm) Thick X 15Mm Wide Pvc Sheet Bending On Inner Side, And Joined Together With Solvent Cement Adhesive. An Additional 5Mm Thick Pvc Strip Of 20Mm Width Is To Be Stuck On The Interior Side Of The ‘C Channel Using Pvc Solvent Adhesive Etc. Complete As Per Direction Of Engineer-In-Charge, Manufactures Specification & Drawing.(For W.C.And Bathroom Door Shutter). , Providing And Fixing Factory Made P.V.C. Door Frame Of Size 50X47mm With A Wall Thickness Of 5Mm, Made Out Of Extruded 5Mm Rigid Pvc Foam Sheet Mitred At Corners And Joined With 2 Nos. Of 150Mm Long Brackets Of 15X15mm M.S. Square Tube, The Vertical Door Profiles To Be Reinforced With 19X19mm M.S. Square Tube Of 19 Gauge, Epdm Rubber Gasket Weather Seal To Be Provided Through Out The Frame. The Door Frame To Be Fixed To The Wall Using M.S. Screws Of 65/100Mm Size Complete As Per Manufacturers Specification And Direction Of Engineer-In-Charge. , Providing And Fixing M.S. Sheet 1Mm Thick Single Leaf Door Shutter In Angle Iron Frame 35X35x5mm Suitabilly Diagonally Braced With 25X3mm Flat Iron Above And Below Lock Rail Of Size 50X5mm Beading Extra Including All Fittings, As Per Direction Of Engg. Incharge But Excluding Cost Of Chowkhats: Including Two Coats Of Anit-Corrosive Red Oxide Primer Paint , Add Extra For Double Leaf Shutters. , Repairs To Plaster Of Thickness 12Mm To 20Mm In Patches Of Area 2.5 Sq. Metres And Under Including Cutting The Patch In Proper Shape, Raking Out Joints And Preparing And Plastering The Surface Of The Walls Complete Including Disposal Of Rubbish To The Dumping Ground Within 50 M Lead With Cement Mortar 1 :4 ( 1 Cement : 4 Coarse Sand) , Providing And Applying White Cement Based Putty Over Plastered Surface To Prepare The Surface Even And Smooth Complete New Plastered Surface (Three Or More Coats) , Wall Painting With Plastic Emulsion Paint Of Approved Brand And Manufacture To Give An Even Shade Including All Scaffolding: Old Work (One Or More Coats ) , Providing And Fixing Welded Mesh/Expanded Metal Mesh In Frame Work, Flat Iron Beading 20X3mm Including Top Cross Laps Inside And Out Sides Welding, Iron Bolts, Crews, Clips Etc. Complete (Excluding Frame Work) Of Size. Welded Mesh 25 Mmx 25 Mm X 2.1 Mm , P & F Pvc Storage Tank Isi Marked (Is : 12701) Indicating The Bis License No), Of Approved Make With Cover, 25Mm Dia 1M Long G.I. Over-Flow Pipe & 25 Cm. Long Wash Out Pipe With Plug & Socket, Including Making Connection Etc., Complete Of Approved Design: 500 (-Do-) , P & F Ball Cock (Is :1703 Mark) With Rod & P.V.C. Ball Complete : Brass Wt.Not Less Than 400 Gm, 20Mm. , P&F Rigid Pvc Pipe (Is:4985 Mark) Class Ii/ (4 Kg. /Cm2.) Approved Quality /Make Including Joining The Pipe With Solvent Cement Rubber Ring And Lubricant. 110 Mm Dia , P&F Rigid Pvc Pipe Fittings (Is: 4985 Mark) Of Approved Quality /Make Including Joining The Pipe With Solvent Cement Rubber Ring And Lubricant: Coupler (Socket) 110Mm Dia , P&F Rigid Pvc Pipe Fittings (Is: 4985 Mark) Of Approved Quality /Make Including Joining The Pipe With Solvent Cement Rubber Ring And Lubricant: Plain Tee 110Mm Dia , P&F Rigid Pvc Pipe Fittings (Is: 4985 Mark) Of Approved Quality /Make Including Joining The Pipe With Solvent Cement Rubber Ring And Lubricant: Bend 45 110Mm Dia , Providing And Fixing Chlorinated Polyvinyl Chloride (Cpvc) Pipes (Is 15778 : 2007 Code) Having Thermal Stability For Hot & Cold Water Supply Including All Cpvc Plain & Brass Threaded Fittings, This Included Jointing Of Pipes & Fittings With One Step Cpvc Solvent Cement , Trenching Refilling & Testing Of Joints Complete As Per Direction Of Engineer In Charge (External Work). 15 Mm Nominal Size , Providing And Fixing Chlorinated Polyvinyl Chloride (Cpvc) Pipes (Is 15778 : 2007 Code) Having Thermal Stability For Hot & Cold Water Supply Including All Cpvc Plain & Brass Threaded Fittings, This Included Jointing Of Pipes & Fittings With One Step Cpvc Solvent Cement , Trenching Refilling & Testing Of Joints Complete As Per Direction Of Engineer In Charge (External Work). 25Mm Nominal Size , P & F Bib Cock (Is : 8931 Mark), Superior Quality Of Approved Make: (-Do-) Long Body, 15Mm Nominal Bore Weight Not Less Than 690 Gm , P & F Inlet Connection (Angle Valves) Superior Quality, Of Approved Make, For Wash Basin, Gyser Etc. C.P. Inlet Connection 15Mm.Brass (Is : 8931 Marked) , Brick Work With Mechanised Autoclaved Flyash Lime Bricks Conforming To Is: 12894 :2002 Of Class Designation 100 In Superstructure Above Plinth Level Upto Floor V Level In. Cement Mortar 1 : 6 (1 Cement : 6 Coarse Sand) , Plaster On New Surface On Walls In Cement Sand Mortar 1:6 Including Racking Of Joint Etc. Complete Fine Finish : 12Mm Thick. , Supplying And Fixing In Walls Machine Cut And Polished Stone Shelves, Tands And In Cm 1:3 With Machine Cut Edges : Kota Stone Minimum 30Mm Thick. , Providing And Fixing Of Double Leaf Steel Shutter For Cupboard, The Frame Is Made Of Pressed Steel Isi Section 80X25 Mmx 1.25 Mm Thick With 1.00 Mm Ms Sheet To Spot Welded Including Holdfasts Of 15X3mm, Ms Oxidized Fittings Such As Butt Hinges, Sliding Doors Bolts, Handles, Tower Bolts And Twin Peg Etc Complete Including Applying Priming Coat Of Approved Steel Primer Of Red Oxide Zinc Chromate And Spray Painting In Approved Shade With Deco Paint Of Approved Quality Complete As Per Direction Of Engineer In Charge , Providing And Laying In Position Cement Concrete Including Curing, Compaction Etc. Complete In Specified Grade Excluding The Cost Of Centering And Shuttering - All Work Up To Plinth Level. M20 Grade Nominal Mix 1: 1.5: 3 (1 Cement : 1.5 Coarse Sand : 3 Graded Stone Aggregate 20Mm Nominal Size).
|
