Tender For Proposed Construction Of Nagar Ayukt Residence At Mathura (Up). in India

Work Detail

Tender For PROPOSED CONSTRUCTION OF NAGAR AYUKT RESIDENCE AT MATHURA (UP).-1 PART-A NAGAR AYUKT RESIDENCE i) Civil Work ii) Plumbing Work TOTAL PART-A 2 PART-F SITE DEVELOPMENT WORK i) Boundary Wall ii) Total Cost of Parking & Road Work iii) Septic Tank iv) Rain Water Harvesting (RWH) Total Cost of Site Development-B 3 PART-C ELECTRICAL WORK a) INTERNAL ELECTRICAL WORK b) EPABX & Networking Work c) SPLIT AC WORK d) EXTERNAL ELECTRICAL WORK Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared EXCAVATION WORK Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. Diluting and injecting chemical emulsion for postconstructionai anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With chlorpyriphos/lindane E.c. 20% with 1% concentration Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20% Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. PCC WORK Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) REINFORCEMENT CEMENT CONCRETE Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland /portland Slag cement, admixtures in recommended proportions as per iS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. concrete of m25 grade with minimum cement content of 330 kg /cum All works upto plinth level Up to Plinth Lvl. All works above plinth level upto floor V level concrete of M25 grade with minimum cement content of 330 kg /cum Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone- III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). SHUTTERING Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers. with water proof ply 12 mm thick Centering and shuttering including strutting, propping etc. and removal of form for Shelves (cast in situ) Centering and shuttering including strutting, propping etc. and removal of form for Weather shed, chajjas, corbels etc., including edges Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform. with water proof ply 12 mm thick Centering and shuttering including strutting, propping etc. and removal of form forEdges of slabs and breaks in floors and walls Under 20 cm wide REINFORCEMENT & MS WORK Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500D or more. Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Providing and fixing factory made single extruded WPC Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 65 x 100 mm BRICK WORK Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) Brick work with clay flyash F.P.S. (non modular) brick class designation 7.5 in superstructure above plinth level up floor five level in : Cement mortar 1:4 (1 cement : coarse sand) Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry with 150mm to 300 mm thick with Grade- AAC blocks of density 551 to 650 kg/cum conforming IS:2185 (Part 3) in super structure above plinth level up floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth upto floor V level. Cement mortar 1 : 3 cement : 3 coarse sand) Extra for plastering done on moulding, cornices architraves including neat finish to line and level: In one coat FINISHING WORK 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Surface Preparation - Exterior surface cleaning / Sanding using recommended tools. Home Sheild Waterproof Putty – Applying 2 coat of the HS Waterproof Putty is a premium quality white cement-based putty that is damp proof and has some unique properties Cured surface after waterproofing with wall putty provides excellent hydrophobicity, exhibiting “Lotus Bead” effect Damp Stop Duo Primer - Applying 1 coat of HomeShield Dampstop Duo primer using a Graco sprayer is a fast and efficient way to get a smooth, even base coat. it is a specially formulated premium quality acrylic primer with superior alkali, damp and efflorescence resistance properties both from positive and negative sides of the wall. Long lasting waterproofing warranty of 7 years on Exterior wall application & 2 years on Interior wall application (T&C applied) Exterior with Longlife 10- Applying 2 coats of Long Life 10 Luxury Exterior paint using a Graco sprayer luxury highperformance exterior emulsion specifically formulated for long-lasting protection and aesthetic enhancement of external surfaces. This product features advanced PU Silicon Technology, offering superior performance under extreme weather conditions and upto 40% dilution on suitably primed/basecoat applied or painted internal walls and ceilings by roller, brush or spray as per manufacturers recommendations. Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured. Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work FLOORING WORK Providing and laying vitrified floor tiles in different sizes thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm Providing and laying full Body Vertified Tiles in floor of 600x600mm sizes (thickness 9mm) with water absorption less than 0.08% and confirming to IS: 15622, of approved brand manufacture, in desired colour and shades, laid with cement based high polymer modified quit set tile adhesive water based) confirming to IS :15477, including grouting of joints. All complete as per direction of E/I (Matt Finish/Glossy) Providing and laying full Body Vertified Tiles in Skirting riser steps of 600x600mm sizes (thickness 9mm) with water absorption less than 0.08% and confirming to IS: 15622, of approved brand manufacture, in desired colour and shades, laid with cement based high polymer modified quit set tile adhesive (water based) confirming to IS :15477, including grouting of joints. All complete as per direction of E/I (Matt Finish/Glossy) 40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 cement : 2 stone dust) admixed with pigment to match theshade of stone and pointing with same mortar. . Red sand stone. Providing and laying Vitrified tiles in floor in different sizes thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm includingngrouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with and admixture of pigment to match the stone shade. 8mm thick (mirror polished and machine cut edge) Granite stone of any colour and shade Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab upto 0.50 sqm Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge give high gloss finish etc. complete as per design approved by Engineer-in-Charge. (Granite work) Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over mm (average) thick base of cement mortar 1:4 (1 cement coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Makrana white second quality DOOR AND WINDOW Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid separately). Second class teak wood Providing and fixing of Teak wood doors shutter 85mm thick ornamental pannelled shutter with Carbing including Teak wood frame/ Chaukats size 75mm thick 245 mm width fixed in position with deshfasners of required dia and length and s/s hings of suitable size including 7 coat of melamin polish of both side complete in all respect as per direction Engineer-in-charge including supplying all material labour T&P etc. required for proper completion . Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorativetype, core block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side adhesive bonding quality conforming to IS : 2046 Type including cost of adhesive of approved quality. 1.0 mm thick Providing and fixing brass Door fifting with lacured polish including labour T&P Complete in all Respect. Door bell Handle 900 mm Handle 600 mm Aldrop 24 " Aldrop 18 " Door Stoper Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles approved quality with necessary screws etc. complete. Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multichambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R3 series with frame (55mm & above) x (40mm & above) & sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every panel along with multi-point locking system (Height upto 1.8m). Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R3 series with frame (98mm & above) x (40mm & above) & both glazed and fly screen sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m) Casement window single panel with S.S. 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles. Using R3 series with frame (55mm & above ) x (45mm & above) & sash (55mm & above) x (65mm & above). (Height upto 1.8 metre) Casement door double panel with French (False) Mullion with zinc alloy (zamak) 3D hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides. Using R3 series with frame (55 mm & above) x (50mm & above) & sash (55 mm & above) x (85mm & above) & French (False) mullion (55 mm & above) x (60mm & above). (Height upto 2.5 metre). Fixed window / ventilator without mullion / transom. Using R1 series with frame (33mm & above ) x (35mm & above). (Height upto 0.90 metre) Fixed window / ventilator without mullion / transom. Using R3 series with frame (55mm & above ) x (45mm & above). (Height upto 2.5 metre) Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) : for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875 – Part 3 (ii) Sites with structure height more than 20m for all wind speeds For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Extra for providing frosted glass panes 4 mm thick (weight not less than 10 kg per sqm) instead of ordinary float glass panes 4 mm thick (weight not less than 10 kg per sqm) doors, windows and clerestory window shutters. (Area opening for glass panes excluding portion inside rebate shall be measured). Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture withmatching wood beading ROOF WORK Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm). Providing gola 75x75 mm in cement concrete 1:2:4 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat neat cement, rounding the edges, making and finishing the outlet complete. Providing and laying integral cement base water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm ofcement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC slab adjoining wall upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken brick bats 25mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining heights upto 300mm height including rounding of junctions of walls and slabs. (c) After two days of propoer curing applying a second of cement slurry using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20mm thick jointless cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed water proofing compound conforming to IS 2645 and approved by Engineer in charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300 x 300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test . All above operations to be done in order and as directed and specified by the Engineer-in-charge with average thickness of 120 mm and minimum thickness at khurra as 86mm Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter Providing and laying POP false ceiling Fixing of channal, TSection, Cross, aluminium jali of heaviar section of more than 700gm use POP of sakarni or eqivalant etc complete. Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) 2011 (Board with BIS certification marks) Providing and fxing of 6mm thick toughen glass complete as per direction E/I. (Approved Rate) Provinding eitching work on toughened glass Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Marine plywood conforming IS: 710 Providing and Fixing Modular Kitechen all Materials & Labour including as per drawiing all complete as per site in charge Providing and Fixing Modular Almirah in Room, Materials & Labour including as per drawiing all complete as per site in charge Total Cost of Building PLUMBING WORK Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid RIMLESS BLIND INSTALLATION WALL HUNG WC KUS-WHT-35953BIUFSMPM) Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid RIMLESS, BLIND INSTALLATION WALL HUNG WC SLS-WHT-6953BIUFSMN) Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: TABLE TOP BASIN, SIZE:510X400X135 mm TABLE TOP BASIN, SIZE:510X400X135 mm Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: TABLE TOP BASIN, SIZE:480X380X140 mm (JDS-WHT-25909) Providing and fixing (SS materials, Make Jaquare) MAZE OVERHEAD SHOWER Ø200X200mm SQUARE OHSCHR- 1619 Providing and fixing (SS materials, Make Jaquare) SHOWER ARM 600X25X25mm SQUARE SHAPE FOR SHA-CHR-455L600 Providing and fixing CONCEALED BODY FOR SINGLE LEVER HIGH FLO (ALD-CHR-079N) Providing and fixing (SS materials, Make Jaquare) SINGLE LEVER EXPOSED PARTS KIT OF HI-FLO KUP-CHR- 35079NKPM Providing and fixing (SS materials, Make Jaquare) SINGLE LEVER EXPOSED PARTS KIT OF HI-FLO (OPP-CHR- 15079NKPM) Providing and fixing (SS materials, Make Jaquare) KUBIX PRIME BATH TUB SPOUT WITH WALL FLA SPJ-CHR- 35429PM Providing and fixing (SS materials, Make Jaquare) required WASTE COUPLING 32mm F. THREAD 130mm HT with Oring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Sleeve/Slip Coupling/ Socket ALD-CHR-705L130 Providing and fixing (SS materials, Make Jaquare) BOTTLE TRAP (WITH INTERNAL PARTITION) 32 ALD-CHR- 769L300X190 Providing and fixing KUBIX PRIME BATH TUB SPOUT WITH WALL FLA SPJ-CHR-35429PM Providing and fixing (SS materials, Make Jaquare) EXPOSED PART KIT OF SINGLE LEVER BASIN M KUPCHR- 35233NKPM Providing and fixing CONCEALED STOP COCK, REGULAR BODY FOR 15) of standard design and of approved make conforming to IS:8931. ALD-CHR-083 Providing and fixing (SS materials, Make Jaquare) EXPOSED PART KIT OF CONCEALED STOP COCK of standard design and of approved make conforming to IS:8931. KUP-CHR-35083KPM Providing and fixing (SS materials, Make Jaquare) EXPOSED PART KIT OF CONCEALED STOP COCK of standard design and of approved make conforming to IS:8931. KUP-CHR-35083KPM Providing and fixing (SS materials, Make Jaquare) HAND SHOWER (HEALTH FAUCET) WITH 8MM DIA ALD-CHR- 573 to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. Providing and fixing (SS materials, Make Jaquare) ANGULAR STOP COCK WITH WALL FLANGE of standard design and of approved make conforming to IS:8931.KUPCHR- 35053PM Providing and fixing (SS materials, Make Jaquare) SINGLE LEVER EXPOSED PARTS KIT OF HI-FLO OPP-CHR- 15079NKPM Providing and fixing (SS materials, Make Jaquare) OPAL PRIME BATH TUB SPOUT WITH WALL FLAN SPJ-CHR- 15429PM Providing and fixing (SS materials, Make Jaquare) MAZE OVERHEAD SHOWER Ø150mm ROUND SHAPE OHSCHR- 1603 Providing and fixing (SS materials, Make Jaquare) SHOWER ARM 20mm DIA & 450mm LONG ROUND S SHA-CHR-479L450 Providing and fixing (SS materials, Make Jaquare) OPAL PRIME BATH TUB SPOUT WITH WALL FLAN SPJ-CHR- 15429PM Providing and fixing (SS materials, Make Jaquare) ANGULAR STOP COCK WITH WALL FLANGE OPP-CHR- 15053PM Providing and fixing (SS materials, Make Jaquare) TOWEL RING SQUARE AKP-CHR-35721P Providing and fixing (SS materials, Make Jaquare) TOWEL RACK 600MM LONG WITH LOWER HANGERS AKP-CHR- 35781PS Providing and fixing (SS materials, Make Jaquare) DOUBLE COAT HOOKCHR-35781PS AKP-CHR-35761P Providing and fixing (SS materials, Make Jaquare) SOAP DISPENSER WITH GLASS BOTTLE ACN-CHR-1135N Providing and fixing (SS materials, Make Jaquare) TOILET ROLL HOLDER ACN-CHR-1151N Providing and fixing (SS materials, Make Jaquare) SOAP DISH HOLDER ACN-CHR-1131N Providing and fixing (SS materials, Make Jaquare) SHOWER BASKET LARGE ACN-CHR-1179N Providing and fixing (SS materials, Make Jaquare) SHOWER BASKET SMALL ACN-CHR-1177N Providing and fixing BRIZA MANUAL STORAGE WATER HEATER 25 LITBZA-WHT-V025 Providing and fixing BRIZA MANUAL STORAGE WATER HEATER 15 LIT BZA-WHT-V015 Providing and fixing SINGLE PIECE SLIM CONCEALED CISTERN BODY JCS-WHT-2400 Providing and fixing (SS materials, Make Jaquare) CONTROL PLATE OPAL JCP-CHR-152415 Providing and fixing (SS materials, Make Jaquare) CONTROL PLATE KUBIX JCP-CHR-352415 Providing and fixing (SS materials, Make Jaquare) JALI SS304, RSF-127 RSF-127 Providing and fixing (SS materials, Make Jaquare) JALI SS304, RSG-127 RSG-127 Providing and fixing SS RACK BOLT L-KEY Providing and fixing WC CONNECTOR 1527926 Providing and fixing GYSER PIPE 18" Providing and fixing TAFLON TAPE Providing and fixing EXTENSION NIPPLE 1" Providing and fixing EXTENSION NIPPLE 1.5" Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P.brass pillar tap Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia Providing and fixing 100 mm sand cast Iron grating for gully trap. Providing and fixing PVC pipe conforming to IS make working pressure 6kg/sqcm including testing labour T&P and all complete fittings 150mm dia 100mm dia Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 50 mm nominal dia Pipes 65 mm nominal dia Pipes Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes 15 mm nominal dia Pipes Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 32mm dia (outer fitting) Providing and fixing gun metal gate valve with C.I. wheel of approved quality {screwed end):. 32mm dia 32mm dia Providing and fixing brass bib cock of approved quality : 15 mm nominal bore Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 Providing and fixing square-mouth S.W. gully trap class SP- 1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required 610x460 mm bowl depth 200 mm Providing and fixing looking mirror superior glass Tappered edge ( approved quality) 6 mm thick fixed on SS Spacers Back Side complete in all respect as per direction of Engineer in- charge. looking Mirror Size( 0.60 M x 0.75M) of Toilet Paper holder Jaquar/ Plumber model no. CHR- 35753 Complete in all respect as per direction of engineer incharge. long body Kitchen bib cock Jaquar (600 mm)model no. CHR-347 Complete in all respect as per direction of engineer incharge. (Quotation Rate) of Fitting (Jaquar/ Plumber make) Complete in all respect as per direction of engineer incharge. (Quotation Rate) Pillar Cock model no.CHR-15001 cock model no. CHR-35037 Provind and laying Commissioning of 1H.P. submersable pump ISI Mark with Starter Complete in all respect as per direction of Engineer incharge.

Contact Information