|
Tender For Special Repair Of P/O/6 Ors Md Accommodation And Provision Of Stores Shed Of Age B/R And Age E/M Under Ge Tenga.; 1 Demolition of cement concrete (unreinforced) in ground floors and paving’s not exc 15 cm thickness (below or above ground level) complete all as specified and directed. 2 M&L for plain cement concrete 75mm thick type C-2, 1:3:6, (40mm graded stone aggregate) as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement. complate all specified and directed 3 M&L for plain cement concrete 75mm thick type C-2, 1:2:4, (40mm graded stone aggregate) as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement. complate all specified and directed 4 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.. 5 M & L for 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished rough to receive tiles complete all as specified and directed.. 6 M & L for Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thickset and jointed in neat cement slurry and pointed in white or colour cement to match all as specified and directed by Engr-in-Charge. 7 M&L for Non - skid Coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of eachtile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in floor complete all as specified and directed. 8 M&L for Non - skid Coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of eachtile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in floor complete all as specified and directed. 9 Taking down cement plaster on brick, concrete stone surfaces etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. 10 M & L 15 mm thick rendering in cement mortar 1:4 on brick or concrete surfaces using WPC @ 3% by weight of cement over 10mm thick backing coat in CM 1:4, finished even & smooth without using extra cement(WPC shall be measured seprately) 11 M & L 15 mm thick rendering on cement mortar 1:6 on brick or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed. 12 M & L 5 mm thick rendering on cement mortar 1:3 on brick or concretesurface in ceiling finished even & smooth without using extra cement complete all as specified and directed. 13 Supply only intregal water proofing compound 14 Preparing new plastered surfaces of wall and applying Two coats of acrylic distemper/ distemper oil emulsion (OBD) , over a coat of alkali resistant primer by Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth all as specified 15 Material & Labour for complete removal of existing treatment and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and directed. 16 Material and labour for preparation of olddistempered surface of wall incl washing down and stoping of distempered surface and appliying one coat of distemper oil emulsion by Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth all as specified and directed 17 Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exc 4 Sqm complete all as specified and directed. 18 Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm complete all as specified and directed. 19 S & F 2nd class hard wood plain solid straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete 20 S & FFramed work as in doors orgates of angle or other sectionwith gusset plates, rails,braces, etc., complete, drilled forfixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete 21 Dismantling wrought iron or mild steel work of any description not otherwise provided for. 22 Material and labour forSteel windows with side hung shutters including projecting typehinges with steel handle, and steel peg stay, complete with glazing bars,dovetailed or weldedall as specified and directed. 23 Material and labour for preparation of new painted steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint all as specified and directed. 24 Material and labour for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed. 25 S&F 30mm Flush shutters, solid core construction, with block board core and plywoodface panels, commercial type on both sides all as completed and specified as directed. 26 S&F30mm thick 2nd class HW Glazed and skeleton shutters, open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats completed and specified as directed. 27 S&FFactory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.all as completed and specified as directed. 28 M&L for preparation of new wooden surfaces of any description, not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 29 Material and labour for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed. 30 Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. 31 M&L forPlywood 12mm, grade BWR,type BB, fixed with screws to timber frame work complete all as specified and directed. 32 S&F MS window guard bars, window frames etc articles confirming to Fe 410-0 or Fe 310-0. complete all as specified and directed. 33 S & F 100mm size mild steel butt hinges medium weight cold rolled and fixed. 34 S & F 75mm size mild steel butt hinges medium weight cold rolled and fixed. 35 S& F Aluminium anodised barrel tower bolts150mm long of extruded section and fixed 36 S& F Aluminium anodised barrel tower bolts100mm long of extruded section and fixed 37 S & F 150mm size extruded aluminium alloy handles, fabricated type anodised 38 Supply and fix 125mm size aluminium anodized handle fabricated type (Make: 39 Supply and fix aluminium anodized barrel tower bolt 125mm long extruded section. 40 S&F 100mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed. Complete all specified and directed 41 S & F 100mm size extruded aluminium alloy handles, fabricated type anodised 42 S & F aluminium alloy, anodised, sliding door bolts 300mm size with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed 43 S&F pre coated mild steel floor door stopper ,tongue anodized 140mm length includingvulcanised rubber piece 44 S & F in repair GI steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm etccomplete all as specified and directed. 45 S&F PVC coated 25mm dia mild steel chromium plated curtain rod of medium weight andincluding fixing brackets, finals and decorative end supports etc complete all as directed” 46 Demolition of Reinforced cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. 47 Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips 48 Mild steel bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips 49 M&L for formwork to chullah hoods,chajjas,troughs and similar items including edges with fair finished flat surface. 50 M&L for Reinforced cement concrete 1:2:4 type B-1(using 20mm graded agg) in chajjas. 51 Demolition of precast cement concrete articles and precast concrete block walling built in cement mortar complete all as specified and directed. 52 Providing precast cement concrete solid building blocks 1:3:6 type C-1(using 20mm graded agg)or slabs 10cm thick (with plain or interlocking joints as directed) setting in mortar 1:4, complete, in walls complete all as specified and directed. 53 Hacking out old broken glass(any thickness, size quality or description)from metal frame incl punching or drilling out old glazing pins/spring clips and providing and fixing new ones. 54 S&F sheet glass 3mm thick ordinary quality and glazing with oil putty in squares n exc0.50 Sqm in each pane. 55 Taking up or down 15mm steel tubing and connections, including cleaning for refixing or removal to store 56 Taking up or down 20mm steel tubing and connections, including cleaning for refixing or removal to store 57 S&F for 15mm bore galvanised iron tube, medium grade,with all newfittings, fixed to walls and ceiling or laid in floorcomplete all as specified and directed 58 S&F for 20mm bore galvanised iron tube, medium grade, with all new fittings, fixed to walls and ceiling or laid in floorcomplete all as specified and directed 59 S & F PVC connection 15mm dia 450 mm long with brass check nuts and washers complete all as specified and directed. 60 S & F in rep 15mm dia CP bib tap, alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specifed. 61 S & F in rep 15mm dia CP pillar tap, fancy type , with capstan heads, chromium plated, screwed down high pressure, with or without lettered "Hot" or "Cold" with long screwed shanks and fly-nuts,screwed for iron pipe and fixedcomplete all as specifed. 62 S & F for CP15mm dia stop cock cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified 63 S & F in rep 20mm bore gun metal globe or gate valve with iron wheel head, screwed down for iron pipe orcomplete all as specified 64 Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specifiedand directed. 65 Supply and fix for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specifiedand directed. 66 Supply and fix for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specifiedand directed. 67 Supply and fix 110mm bore PVC (SWR) bends any radiuswith access door complete all as specified and directed. 68 Supply and fix 110mm bore PVC (SWR) junction single , (single T) equal or unequalwith access door complete all as specified and directed. 69 Supply and fix 75mm bore PVC (SWR) bends any radiuswith access door complete all as specified and directed. 70 Supply and fix 110mm bore PVC (SWR) vent cowl complete all as specified and directed. 71 S&F PVC (SWR) floor trap, 75mm dia outlet, plain with grating incl jointing with solvent cement. 72 S&F sinks made of stainless steel lmmthickkitchenorlaboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete as specified and directed 73 Dismantling of water tanks exc 250 ltrs & n. exc 500 ltrs capacity and removing to store. 74 S&F PVC water storage tanks of 750 ltrs capacity rotational moulded (multi layered cylindrical vertical with closed top) hoisted and fixed in position all as specified in(Make : Sintex/Polycon /Poly Tap ) 75 S & F ball brass valves, high pressure, with polyethene float and flynut complete screwed for iron pipe of 20mm dia all as specified. 76 S & F in repair Wash basins, Vitreous China 400X400mm (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand with Waste fittings, brass, chromium plated for glazed ware sinks, basins,etc. with long screwed shanks and fly-nuts, flange end beddedinred leadcement and other end fixed ,Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections includingnecessary packing, union and cap and fixed 77 S&F in rep looking mirror 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers 78 S&F in rep vitreous China squatting pan,‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests , including connecting to trap and to flushing pipe and complete. 79 S&F in repPVC valveless, syphonic action type, flushing cistern,low level, white, with inlet,ball valve, float and handle including brackets complete. 80 M&L for Towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms) 81 M&L for Sunken Treatment of Toilet Bathroom(including Demolition as in following steps:i)Top of RCC slab in sunken portion including peripheral beams shall be plastered with 15mm thick in CM 1:3 using approved water proofing compound @ 3% by weight of cement finished even & smooth using extra cement ,curved at the junctions. ii)Apply two coat of epoxy resin/polymer modified cementations coating like a brush bond of FOSROK/SIKA/Pedilite or equivalent, both on floor & beams.iii)Sunken slabs to be given 1:20 slope outword 25mm GI pipe spout with 300mm projection beyond outer surface of wall shall be provided. iv)Water tightness of sunken portion to be tested by ponding with water for 72 hours.In case of even a slight mark of seepage,the portion to be treated and ponding shall be carried out again to confirm the water tightness of sunken slab.v)The sunken portion will be filled with lean concrete 1:4:8 type D-2 using brick agg to req depth. Note:No cutting in roof slab/beam shall be allowed for passing of CI pipes & fittings.The stage of water proofing to sunken slab shall be passed by Eng-in-charge/GE. 82 M&L for taking down of existing tarfelt and bituminous compounds in roof of any discription from roof or terracing,roughening surfaces of old concrete surface by picking u,sweeping clean and washing down with water to remove dust etc providing 15 mm thick screed bed or bedding layer of CM(1:4) for laying water proofing membrane and finishing surface even and smooth w/o using extra cement and providing water proofing treatment over smooth finished surface after applying hot bitumen 85/25 @ 1.2 kgs/Sqm providing laying APP polymer, modified,non-woven polyster mat,reinforced membrane,3mm thick(min)weighing 3.50 kg/Sqm with surface finish of white mineral,by torch application method,with minimum 75mm overlap on longitudinal direction and 100 mm overlap on the transverse direction and finally applying one coat of bituminus based solar reflective aluminium paint @ 100Gms/Sqm over PP modified membrane all as specified and directed. 83 Surface dressing n exc 15 cm deep in soft/ dense soil complete all as specified and directed by engr in charge 84 Excavation in trenches n. exc 1.5 m wide and n.exc 1.5 m deep for foundation and getting out in hard/dense soil. complate all specified and directed 85 Excavation in post hole each n.exc 0.5 cum and getting out, returning filling in and ramming earth or brocken rubble mixed with earth around, in layer n.exc 25 cm watering and removing surplus soil to a distance n.exc 50 cm and making good in hard/dense soil complete all as specified and directed. 86 M&L for cement concrete type D-2, 1:4:8in Cement concretein foundations, filling and mass concrete complate all specified and directed 87 M&L for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete. 88 M&L hard core of gauge n.exc 63mm, deposited, spread and levelled in layers nexc 15 cm thick, using broken stone or boulders, watered and rammed to a true surface. 89 M&L for PCC 75 mm thick, type D-2, 1:4:8(using 40mm graded sone agg) in sub-floors, sub-base, floors and pavings etc.complate all specified and directed 90 M&L for 40 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) in flooring even and smooth with using extra cement.complete all as specified and directed. 91 M&L for 28mm Glass dividing strips, 3 mm thick inserted in position, conform to design 92 M &L for 15 mm thick screed bed in CM 1:4 for laying floor tiles complete all as specified and directed 93 M&L for chequed cement concrete tiles 20cm X 20cm X 25 mm thick, set jointed and pointed in neat cement slurry in floors with grey pigment cement and pigments 94 Erection and fixing only rolled mild steelfor Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections)incl distance pieces, cleats etc, Fe- 290 (Gde E- 165).complate all specified and directed 95 S&F rolled mild steelfor Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections)incl distance pieces, cleats etc, Fe- 290 (Gde E- 165).complate all specified and directed 96 Supplied and fixed Expanded metal n exc 4 kg per Sqmcut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples complete to wood or steel members 97 Fixing only (Except sheeting) 0.63 mm thick corrugated galvanised mild steel sheeting (minimum 275gm/sqm galvanising) with two corrugations side lap, fixed with L type or J type or cranked hooks , bolts and washer in walls, complete, all as specified and directed. 98 Supply and fix, 0.63 mm thick corrugated galvanised mild steel sheeting (minimum 275gm/sqm galvanising) with two corrugations side lap, fixed with L type or J type or cranked hooks , bolts and washer in walls, complete, all as specified and directed. 99 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified 100 S& F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified 101 M&L for Preparation ofnewlyplastered wall surfaces and applying Two coats of cement base paint on external wall surfaces over one coat of primer 102 M&L for preparation of newly plastered internal surfaces of walls and applying two coats of oil bound distemper,over a coat of primer complete all as specified 103 M & L for providing 4mm thick "E" Board in ceiling with galvanised iron snap frame of "T" section 24 x 38 x 0.70 mm wall/ceiling angle 25x25x0.35mm thick and hanging with 4mm Gl wire all fixed arrangement will be done as per manufacturer instruction incl two coat of oil bound distemper anirected.d one coat of white wash complete all as specified and directed by engr in charge. 104 M&L for preparing and applying two coat of synthetic enamel over a primingcoat onnew zinc (or galvanised ) surfaces to receive painting, by coating with mordant solution including washing and cleaning etc. of any description, not otherwise described, over 10 cm width or girth. 105 Supply & fix sheet glass 4mm thick ordinary quality and glazing with oil putty in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed. 106 M&L for 2nd classhard wood 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated 107 S&F Mild steel flat ironas in hold fasts; complete all as specified. 108 Returning/filling in including spreading, levelling, watering and well remming in layers n.exc 25 cm in hard/dense soil. complate all specified and directed 109 Removing excavated material n.exc 50m and depositing where directed at a level n exc 1.5m above the starting point.complate all specified and directed 110 Dismantling of plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof coverings complete all as specified and directed 111 Dismantling framed trusses (Steel or iron) n exc 10 m Span 112 Dismantling structural steel work including doors, gates but excluding framed truss etc. 113 Dismantling framed timber scantlings 40 sq. cm and over in section, in any position 114 Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles 115 Material & Labour for light Point wiring with 1.5 sq mm (nominal area), PVC insulated unsheathed (FRLSH), 1100 volts grade, multi-stranded copper conductor, in and including PVC casing capping of adequate size with all fittings and accessories including PVC boxes for housing the switches ( Make of box Prestoplast,Prestoteak), including PVC insulated and unsheathed (FRLSH)single core multi-stranded copper conductor cable of size 1.5 sq mm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed. 116 All as per item No. 114 here in before but one exhaust fan point controlled by one way switch all as specified and as directed . 117 One light point controlled by two two-way switch 5/6 Amp complete all as specified and as directed . 118 One bell/buzzer point controlled by one bell push complete all as specified and as directed . 119 All as per item No. 114 here in before One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5sq. mm size 120 All as per item No. 114 here in before but for one 3 pin socket outlet 5 Amps three pin controlled by one switch on independent board complete all as specifieddirected. 121 All as per item No. 114 here in before but for one 5 pin socket outlet 15 Amp and 5 Amp Multipurpose independent using 2.5 Sqmm copper conductor cable (multi-strand) PVC insulated and unsheathed cable and 2.5 sqmm copper (multistrand) PVC insulated and unsheathed earth wire withPVC boxes complete all as specified. 122 M&L for Point wiring for one socket outlet 15 Amp on independentboard with 4 sq mm (nominal area), PVC insulated unsheathed (FRLSH), 1100 volts grade, multi-stranded copper conductor, in and including PVC casing capping of adequate size with all fittings and accessories including PVC boxes for housing the switches ( Make of box Prestoplast,Prestoteak), including PVC insulated and unsheathed (FRLSH)single core multi-stranded copper conductor cable of size 4 sq mm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed. `(For Geyser ) 123 S&FSocket outlet 2 in 1, 3 pin, 5amp flush type 124 S&FSocket outlet 2 in 1, 3 pin, 5 and 15 amp flush type 125 Supply & fixing switch piano flush type (ISI marked), single pole, one way 15 Amp, 240 Volts complete all as specified & directed. 126 Supply and fixing ceiling rose, surface bakelite, 65mm x 50mm ,two to three terminals complete all as specified & directed. 127 Supply & fixing switch piano flush type (ISI marked), single pole, one way 5 Amp, 240 Volts complete all as specified & directed. 128 S&F switch piano two way, 5/6 Amp, flush type (ISI marked), single pole, complete all as specified & directed. 129 S&F bell/buzzer push 5/6 Amp,flush type complete all as specified & as directed. 130 S&F call bell ding dong electric AC, 240 volt, 50 HZ, surface type complete all as specified & as directed. 131 Supply and fixing lamp holder, insuleted body with pack plate suitable batten fitting on wall duly grouted/fixed in solid block wall or on wooden boardcompleteall as specified and directed. 132 S&F LED lamp 10 Watt, CDL, B-22 cap, (Pin type), 230W, PF not less tha0.85 (min). 133 Supply and fixing LED light fitting 1 x 20 Watt 220 volt AC decorative box type with driver, holder including LED tub light connecting up with three core flexible copper conductor cable of size from ceiling rose complete all as directed. 134 S&F of new generation energy saving and environmental friendly long life LED building securitylight made up of innovative die cast aluminium housing high power LED as lighting source with IP - 66 power consumption 35 watt complete input voltage of 150-240 Volt (nominal rated voltage 240 Volt) complete including GI brackets with fixing arrangements & connected items,twisted 3 core copper cable of size 1.5 Sqmm dia for connecting phase, neutral and earth from ceiling rose to light length as required at site all as specified and directed. 135 S&F LED bulkhead fitting 10 watt (Endura Ruby) with all accessories and including connenting up with twin core twisted with flexible copper conductor cable with suitable size of 230 volts , 50 hz complete all as spicified and directed. 136 Supply and fix sheet metal enclosures for DBs when MCBs to be used 230 volts 8 way 200 Amp rated busbarsingle pole and neutral fixed on wall duly grouted in solid block wall or on wooden board. 137 Supply and fix sheet metal enclosures for DBs when MCBs to be used 230 volts 4 way 200 Amp rated busbarsingle pole and neutral fixed on wall duly grouted in solid block wall or on wooden board. 138 S&F MCB SPN having braking capacity 10KA, 32 Amps, 240 Vcomplete all as specified and directed. 139 S&F MCB SP having braking capacity 10KA, 6 to 32 Amps, 240 Vcomplete all as specified and directed. 140 S & F exhaust fan sweep 300 mm voltage 230 V 50 Hz 1200 RPM noiseless metal body light-weight rust proof body self closing louvers and blades complete all as specified and as directed. 141 MCCBDB"s VTPNtype double door in wall / nitchwhen MCBB"s ,to be used Fourpole and neutral, 8way,415 Volt withrated Bus bar ,Suitable for Flush Mounting and Surface Mounting with 160 Amps Copper Bus bar for each phase and 2 Neutral bar, 2 Earth bar,and Cable ties for cable managent,Fully insulated busbar and shrouded Neutral bar ,improved Panassembly for ease of installation ,Prefitted masking sheet, Reversible Door for IP 43 &IP 54 DB"s with provisionfor DPX3 160 MCCBasincomer, andTPN /SPN/DP/SPout going.complete all as specified and directed.IP :54 Protection 142 S&F MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA 143 Supply and fix electronic meters temper proof LCD display with polycarbonate cover 230 V, 10-60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH 144 Supply and fix electric water heater(Geyser), storage type steel body with copper inner tank and heating element up to 2 KW capacity 25 litre, BEE 5 star rated adjustable temprature setting 0-90 degree C complete with accessories such as safety wall, thermostate, NRV indication lamps, inletoutlet connections,air vent connections, connection pieces including all fixing arrangements such as fastners, bilts, nuts washers etcincluding making good disturbed wall surfaces matching with the existing surface and finishing complete all as specified and directed by Engr in charge 145 Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15 mm bore(medium grade) and connected to main switch board or main control board as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm C/C with one handle for liftingmade out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete all as directed by Engineer-in-Charge. 146 S&F wire for circuit/sub main wiring with 1100 volts grade double core PVC insulated and unsheathed cable with multistranded copper conductor 6 Sqmm, on surface or recessed or drawn in PVC casing capping/PVC Pipealong with 4 Sqmm single core copper conductor multi stranded cable as earth continuity conductor complete all as specified and as directed.(Note: One RM PVC casing capping/PVC conduit ,one run of 4 sqmm earth wire and 2 Run of 6 sqmm cable shall be measured as one run.) 147 Taking down point wiring carefully copper/ aluminum (light,fan, socket or power) complete (fittings such as switches ceiling rose, pendents, regulators, sockets etc) 148 Taking down main switches, DBs alongwith existing board and removing the same from the site and making good the disturb surfaces / Portion of the wall etc all specified and directed by EIC. 149 Taking downsub main wiring of any type and size and discription incl removal from DBs etc and removal of the same from site and making good the disturb surfaces or portion of wall/ceiling etc complete all as specified and directed by EIC. 150 Supply & laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electirc cables with stranded aluminium conductor, 1100 volts grade, of 10 Sqmm 2 core complete all as specfied and directed. 151 S&F in replacement of 2 mm thick MS meter box rectangle type wall mounted including Provision of space for 04 Nos single phase meters, 01 x MCCB 100 Amp as main incoming, 04 Nos aluminum bus bar 150 Amp capacity, and necessary connection complete
|
