|
Tender For Special Repair To Bldg No T-57, Drainage Sys (Approx 200Rm), Internal Road And Certain Misc Works Under Ge Jhansi; 1 Demolition of cement concrete incl terrazo flooring (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level) built in cement mortar, complete all as specified and directed. 2 M&L for 75 mm thick cement concrete type D2 1:4:8 (using 40 mm graded stone agg) in sub base of flooring/ hard standing complete all as specified and directed. 3 M&L for 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) as in plinth protection and path laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) surface, complete all as specified and as directed.(Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings.) 4 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed. 5 M&L for Non skid ceramic colored tiles , 7 to 8 mm thick (square / rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqmas in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed. 6 M&L for ceramic colour tiles in vertical surface of size 350 X 250 x 7/450x300x7 mm thick, , set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and as directed. 7 M&L forNon-skid colour ceramic tile tiles8 to 10 mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry over 15 mm thick screed bed or bedding layer in CM 1:6 over brushing neat cement slurry @ 3Kg/sqmetc complete all as speciefied and directed. 8 All as per item here-in-above but on vertical surfaces such as skirting/dado over and including 10mm thick CM rendering (backing coat) in CM 1:4,complete all as specified and as directed. 9 Dismantling stone slabs and tiles of any description or thickness laid , bedded and pointed in any mortaras in floors, aprons etc. complete all as specified and directed. 10 M&L for factory made machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, with and including 50mm thick sand cushioning, , complete all as specified and directed. 11 M & L for machine cut kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 10 mm thick backing coatin CM 1:4 complete all as specified and directed.Note: Kota stone in Step will be placed in single piece with groove lines at edge. 12 M&L 18-20 mm thick granite slab of any type , tabled rubbed, machine cut, duly grinding, polishing, moulding etc of all outer edges / sharp corners, duly fixed in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4), incl pointing in grey cement (1:3) using marble dust with admixture of pigment to match with the shade of slab, complete all specified and directed. 13 Dismantling timber scantling 40.0 sqcm and over in section in any position as in framed / unframed works such as roof purlins, rafters, fillets, ridges etc as in roof/ ceiling, complete all as specified and directed. 14 M& L for clean sawn 2nd class hard timber scantling in truss work , frame work etc, fixed with U hook with Nut bolt complete all as specified and dirceted. 15 M & L18/19 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including dismantling of old boarding, cupborad any description, fixed in any position including fittings, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately) 16 M & L25 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws,including dismantling of old boarding, cupborad any description, fixed in any position including fittings , all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately) 17 Providing and fixing 2mm thick 18 to 25 mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per directions of Engineer- in-charge. 18 S&F continuous (piano) hinges, mild steel bright finish in electro galvanized width of flat (when open) in 30mm, complete all as specified and directed 19 S & F drawer/shutter handles, projection drop (50mm to 65mm) on screwed platey complete all as specified and directed 20 Supply & Fixstainless steel magnetic catcher fancy type for kitchen cabinet / drawer complete all as specified and directed by Engineer-in-Charge. 21 Demolition of brick work built in cement mortar or lime mortar including all quoins, arches, pillars etc complete all as specified and directed. 22 M&L for brick work with old size fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed. 23 M&L for brick work with old size burnt bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed. 24 M&L for10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement), complete all as specified and directed. 25 M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4 with WPC ) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement), complete all as specified and directed. Notes: WPC in 5 mm thick 2nd layerplaster measured and paid separately. 26 M&L for10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirtingetc including racking out joints hacking for key scrubbing down with water etccomplete all as specified and directed. 27 M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4 with WPC) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirtingetc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed. Note: WPC in 5 mm thick 2nd layer plaster measured and paid separately. 28 M&L for5 mm rendering thick in CM (1:3) on fair faces of concrete surfaces in ceiling finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirtingetc including racking out joints hacking for key scrubbing down with water etccomplete all as specified and directed. 29 M&L for preparation of new plastered of wall surface and applying two coats of oil bound distemper, over a coat of chalk whitening primerover and incl a layer 3mm thick of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed. 30 M&L forpreparation of surfaces of wallsand applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof)of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. complete all as specified and directed.Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer"s drums with seal intact. 31 M&L for preparation of newly plastered surfaces and applying two coats of white wash on ceiling all as specified and directed. 32 M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping from old treated surfaces of wall and applying two coat of oil bound distemper over a coat of chalk whitening primer, over a layer of (JK/Birla) 3.0 mm thick wall care putty to get smooth and level finish, complete all as specified and directed. 33 M&L for complete removal of existing treatment and preparation of surfaces of walls by scrapping/sand paper rubbing and finally washing with wateringand applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof)of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. complete all as specified and directed.Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer"s drums with seal intact. 34 M&L for preparation of newly plastered surfaces surfaces of wall and applying two coats of white wash on wall all as specified and directed. 35 Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each including cutting holes in brick/ stone wall built in cement / lime mortar, embedded portion exc half brick but n.exc one brick for inserting new hold fast and making good the disturbed portion/surfaces, in CM 1:3 complete all as directed. 36 All as per item here-in-above but not exc 1.5 sqm each 37 Taking down shutters of any description not exc 01 Sqm each, complete all as specified and directed. 38 S & F for Factory made double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified & directed. 39 S & F Solid PVC Door Frame single side prelaminated pvc sheet or plain colour pvc sheet & edges willbe painte to match with printed sheetof size 50mm x 47mm made out of 5mm thick prelaminatedcolour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. 40 S&F Factory made single 35 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. 41 M&L 30mm thick factory made solid WPC (Wood plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including stainless steel wire shall mesh be fixed with 15x15 Square tube in side rails with screwing 8x28 heat metal zink coated screws can be remove or fie again of the shall be as per manufacture instruction complete all as specified and complete all as specified and complete all as specified and directed. 42 S &F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm prelaminatedcolour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. 43 Supply and fixing of powder coated (Min thickness of powder coating 50 micron) anodised aluminiumframe section of door, windows, ventilation, partion wall, cup board with one or more rebates including joinging cleats for fixing etc. complte all as specified. 44 Providing and fixing powder coated anodised aluminium window and ventilator shutters, hung/sliding type without sashbars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading,screws, anodised aluminium fittingssuch as peg stays 150 mm long (1 No.) hinges type B-21 100 mm long (2 nos.) suitable handle (1 no.) etc all as specified and directed . 45 S & F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work fixed with holdfast or fastener if required conforming to Fe.290.Gde-E-165 complete all as specified and as directed. 46 Supply only 4.0 mm thick selected quality sheet glass plain/figured in squares n exc 0.50 sqm each pane complete all as pecified and directed. 47 S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed 48 S&F of aluminium alloy anodized sliding door bolt 300mm (aldrop bolt) length with hasp staple and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixedcomplete all specified and directed 49 S&F of 125 mm size butt hinges, extruded aluminum alloy with galvanized mild steel pin type B-21anodized complete all specified and directed 50 S&F of 100 mm size butt hinges,extruded brass, with mild steel hinge pin, bright polishedand fixed, type B-11 complete all specified and directed 51 S&F of 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed. 52 S&F of 150mm aluminum handle cast type anodized complete all specified and directed. 53 S&F of mild steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed 54 S&F of 140 mm door stopper of aluminium body and tongue anodized with hard drawn steel spring fixed in floor complete all as specified and directed. 55 S&F Rubber bush (door seal) of 25mm wide fixedto door complete all as specified and directed 56 S & F in repair stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets, complete all as specified and directed. 57 S&F of ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed. 58 S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors,including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed. 59 S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and patterncomplete all as specified and directed. 60 S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed. 61 S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed. 62 S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed. 63 S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed. 64 S&F PVC(SWR) vent cowl 110mm bore, jointing to waste pipe, complete all as specified and directed. 65 S&F PVC floor trap of 75 mm outlet, jointing to waste pipe, complete all as specified and directed. 66 M & L for PVC (SWR) gully trap 110 mm, setting and jointing with solvent cement complete all as specified and directed. 67 S & F 15 mm bore Galvanized Steel tubes, medium gradefixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed 68 S & F 20 mm bore Galvanized Steel tubes, medium gradefixed to walls and ceilings or laid in floors,concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed 69 M&L for cutting chases, pinning in for concealed water tubing, not exc 10 cm girth and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc complete all as specified and directed. 70 S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered white colour 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed. 71 S&F in repair20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. 72 S&F in repair20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as directed. 73 S&F in repair 600x450mm size and 4mm thick beveled edge looking mirror of selected quality glass, having PVC moulding/beading all around, mounted on 4mm thick PVC board, with and incl fixing accessories, complete all as specified and directed. 74 S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure,with long screwed shanks and fly-nuts, complete all specified and directed. 75 S&F in replacement of stop cock/anglecock with long shank and cup (concealed type), 15mm dia with wall flange, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe / unions, complete all as specified and directed. 76 S&F in replacement of overhead shower of dia 125 mm round shape single flow, ABS body chrome plated fancy type, with and incl swivel type shower arm of 20mm dia with wall flange made of cast copper alloy, chromium plated fancy type,complete all specified and directed. 77 S&F in replacement of long body bib cock, 15 mm dia with wall flange made of cast copper alloy, chromium plated,complete all specified and directed. 78 S&F in replacement of angular stop cock 15 mm dia with wall flange made of cast copper alloy, chromium plated type, complete all specified and directed. 79 S&F in repair SS grating of squre/round shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and incl fixing with CM to floor/nahani traps etc, complete all specified and directed. 80 S&F in replacement of towel rail 600 mm long D type between flange and wall bracket made of cast copper alloy, chromium plated, complete all specified and directed. 81 S&F in replacement of Brass CP connection 15mm dia and 45cm long with 2 Nos brass check nuts with washers for geyser, complete all as directed. 82 S&F in replacement of PVC waste pipe 32 mm dia 750 mm long with for wash hand basin or for kitchen sink, complete all as specified and directed. 83 S&F in replacement of PVC connection 600 x 15mm dia PTMT (PVC), complete all as directed. 84 S&F in replacement of 10 ltr capacity PVC valve less symphonic action type flushing cistern, white, with inlet ball valve, float and handle with and including wall bracket, 32 mm dia PVC flush pipe and connected to squat pattern / pedestal pattern water closet, including all joints and making good to the wall & floor,complete all specified and directed. 85 S&F in replacement of 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet including flush pipe, P Trap and connecting conebut exluding flushing cistern, duly fixed in lime concrete bedding and making good of floor surface, complete all as directed. 86 S&F in replacement of 1st quality vitreous china ware European type WC with "P" or "S" type traps and same make plastic seat cover of white colour including flush pipe, fixing bolts etc and making good of the wall & floor surface, complete all as directed. 87 S&F in replacement of 1st quality vitreous china wash hand basin, white flat/angle back or oval shape for countertype, size 550x400mm, complete including necessary cutting for and pinning in ends of brackets) with and including wall brackets, PVC waste pipe of 750mm long, CP waste coupling of 32mm dia size,complete all as specified and directed. 88 S&F in replacement of corner glass shelf 300 mm with Chromium plated bracket guard and railing and fixing accessories, complete all as directed. 89 Removing existing water proofing treatment by brushing with wire brush, cleaning of terracing by taking down cement concrete, existing plaster lime cova 80 to 100mm thick mud phuska/cement concrete/lime coba /brick layer etc, cleaning of all foreign material such as fungus mass dust etc, roughing surface of corner to roof by wire brush complete all as specified and directed. 90 M&L of water proofing treatment to non-accessibleroof slabwith APP based modified polymeric membrane centre core 100mm micron HMHDPE outer film 20 micron each having thickness 3mm weight not less than 3kg/Sqm as per manufacturer’s instructions laidwith torch application complete all as specified and directed by Engineer-in-Charge with following course of description below:-(a) 10 mm thick plaster in CM 1:4 with WPC (liquid water proofing compound @ 0.20 Ltr/bags(50 Kg Bag))will be applied over the roof slab (subjected to condition as mentioned in notes) . After the plaster is cured the roof will be tested for water tightness by ponding with water for seven days for any seepage is observed the rectification will be carried out by pressure grouting under the pressure of 5kg/sqcm using cement based grout. After the surface is repaired the slab will be tested for water tightness again before proceeding with further treatment. 91 (b) the surface of roof, parapet and gutters, drain mouths, etc. over which waterproofing treatment is to be applied shall be cleaned of all foreign matter such as, fungus, moss, dust etc by wire brushing and dusting. For cast iron drain outlets a groove shall be cut around to tuck in the treatment. Concrete angle-fillets shall be provided at junctions between roofs and vertical faces of walls (parapet and other walls) around obstacles such as pipes, chimney stacks, etc. and other similar situation to ease up about corners.(c) Bitumious based primer confiorming to IS: 3384 @ 0.3 kg/Sqm to be applied on prepared surface, till the surface is propely impregnated. (d) After the application of approved bituminous primer the water proofing membrane shall be laid on the primed surface by torch application method as per manufacturer"s instruction. The overlap while toching shall be 100mm in longitudinal direction and 100 mm in transverse direction. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer and seling it with the help of hot trowel. The overlap joints shall be made as a monolithic layer.(e) All joints and changes in direction should be curved with cement mortar 1:3 mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane.(f) after apllication of APP membrane one coat of aluminium paint @ 0.20 Kg/Sqm over APP membrance will be applied Note :The cost of all items i.e. from Sr No. (a) to Sr No.(f) are included in quoted rate and no separate payment will be done for the above except liquid WPC. 92 M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as inroof kerbs,tank staging etc complete all as specified and directed. 93 Supply only integral liquid water proofing compound LW++, mixed in CM as per manufacturer instruction,complete all as specified and directed. 94 Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth for laying of GI Pipe and getting out in any type of soil complete all as specified and directed by Engineer-in-Charge. 95 Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m depth, for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 sqm on plan and n.exc 1.5 m in dedpth and getting out hard/dense soil complete all as specified and directed 96 Excavation in trenches in any type of soil n exc 1.5 mtr wide and not exc 1.5 mtr in depth and getting out excavated soil complete all as specified and directed. 97 M&L for Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm and getting in loose soil all as specified as directed. 98 M&L of removing excavated material nexc.50 m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as well as specified 99 M&L for cement concrete 1:2:4 type B1 (20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, copings, bond stones, bed plates for hold fast and the like including weathering, slightly rounded or chamfered angles and throating,complete all as specified and directed. 100 M&L for reinforced concrete pipe Class NP-2, 150mm dia with coller laid jointed with CM 1:3incl breaking up any types of pipes complete all as specified and directed. 101 M&L for PCC 1:3:6 type C2 as in concrete bed to 150 mm bore drain pipe and over incl packing under haunching against the sides of pipes after pipe laid and tested complete all as specified & as directed. 102 S&F of pre-painted 0.50mm thick Gavalume Aluminium Zinc coating GI based corrugated / semi corrugated / trapezoidal steel sheet of any colour having tensile strength 550 MPa and AZ 150 grade as in roof covering/cladding to walls, fixed with self tapping screws, complete all as specified and directed. 103 S&F pre-painted Galvalume Aluminium Zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength 550 MPa and AZ 150 grade as in ridge of roof covering, fixed with self tapping screws, complete all as specified and directed. 104 M&L for structural steel Fe-410-W(Gde-E-250) quality A for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed. 105 S&F in repair the exposed frame false ceiling system with GI powder coated grid consisting of interlocking arrangement of main T runner of 15mm size, suspended at 1200mm C/C and cross T runner of 15mm size suspended at 600mm C/C supported by 1.5 mm dia GI wire from roof/Slab/truss including wall/perimeter runner/channel of 15 mm size with and including 4mm thick pre-painted non asbestos fiber reinforced cement board (E-board), designer type of size 595x595mm duly fixed in ceiling frame work complete all as specified and directed. 106 M & L in repairfor two coat of synthetic enamel paint over one coat of red oxide, zinc chromiume on steel surface including preparation of new steel surface width or girth exc 10cm all as specified and directed. 107 S&F in repair 5 mm thick beveled edge looking mirror of selected quality glass, having PVC moulding/beading all around, mounted on 4mm thick PVC board, with and incl fixing accessories, complete all as specified and directed. 108 M&L for cement concrete in foundation, filling and mass concrete type D2 1:4:8(using 40 mm graded stone aggregate), complete all as specified and directed. 109 M&L for cement concrete insurface channels anddrains type B11:2:4(using 20 mm graded stone aggregate), complete all as specified and directed. 110 M&L forrendering 10 mm thickon fair faces of brick work orconcrete surfaces in CM 1:4finishing surface even and smooth (withoutusing extra cement), complete all as specified and directed. 111 M&L for forming fair finished drain or channel over 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc., complete all as specified and directed. 112 M&L for cement concrete type C1,1:3:6 (using 20 mm graded stone aggregates) as in roof kerbs or stops, lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. 113 Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. but excluding Fan & Geysers and removing materials to storefor taking credit and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed. 114 M&L for point wiring for modular fittings complete with 1.5 Sqmm FRLS insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLS insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm(OD), concealed in wall/ floor etc including provision of modular cover plates with frames and 1.50 sq mm PVC insulated unsheathed stranded copper conductor (FRLS) cable for common earth and connecting to earth dolly all as specified and directed by Enrg-in-charge. (Note- rates of chasing/cutting & making goods shall be included in the unit rate) :- 115 One light point/ceiling fan/exhaust fan controlled by one switch 116 One 6A socket point controlled by one switch on independent board 117 One 6A socket point controlled by one switch on same board 118 All as per srl item No 113 here-in-before but with 2.5 sq mmFRLS copper wire with 2.5 Sqmm FRLS copper earth wire for one 16 Amp socketpoint controlled by one 16 Amp switchon independent board. 119 Taking down submain wiring of any size any type and in any position metalic/non metallic PVCconduit of wooden batten complete all as specified and directed. 120 M&L for submain wiring alongwith earth wire 2 runs x 6 sqmm + 1 run x 6 sqmm with FRLS insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit ISI Markedconforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc and directed by Engineer-in-Charge.Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length 121 All as per srl item No 116 here-in-before but2 runs X 4 Sqmm + 1 run X 4 Sqmm. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length 122 All as per srl item No 116 here-in-before but2 runs X 2.5 Sqmm + 1 run X 2.5 Sqmm. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length 123 S&F of Modularswitch1way6A,1 module 240V, 50Hz complete all as specified and directed. 124 S&F Fan step regulator, 120W - 2 module, 240V, 50Hz ISI marked with valid CML complete all as specified and directed. 125 S&F of Modular Socket,6A - 2/3 pin combined 2 module 240V, 50Hz complete all as specified and directed. 126 S&F of Modularswitch1way16A,1 module 240V, 50Hz complete all as specified and directed. 127 S&F of Modular Socket6A/16A - 2/3 pin combined 2 module 240V, 50Hz complete all as specified and directed. 128 S&FCeiling rose, three terminals, bakelite body, 240 volts, ISI marked with valid CML complete all as specified and directed. 129 Taking down light fitting of any capacity and any sizeand in any position complete all as specified and directed. 130 S&F decorative Stylo wall light of color Opal white PC Diffuser for Glare Free Light up to 14 Watt white LED retrofit lamp suitable for B-22 holder base with polycarbonate mounting on wall bracket IP 20 complete etc. 131 Supply and fixVentilataing fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50HZ, RPM 1200, Copper winding of sweep 250 mm including connection with 1.5 sqmm, three core copper wire from ceiling rose to exhaust fan upto 1 mtr length including fixing on ventilator complete all as specified and directed by Engr-In-Charge. 132 S&F LED Tube light fitting batten type 20W, 230W, efficiency 120 Lumens per watt, colour temperature6500k (Cool White), Power factor grater than 0.9, Polycarbonate body, CRI 80, IP Rating, IP 20, THDv with in 5 % and THDi (8-10%) and integrated Electronic driver complete with al accessories internally Pre-wired and including connecting with 3 Core twisted flexible copper conductor cable of suitable size from celling rose all as specified and directed.Notes:- (i) The rate of three core twisted flexible copper conductor cable of suitable size for connection is included in this item and noting shall be paid extra on this account.(ii) Warranty for replacement of each LED lite fitting shall not be less than 2 years from the date of purchase.(iii) Date of purchase shall be marked on each fixture with permanent marker for redeeming warranty benefits. 133 Supply and fix in replacement of LED bulkhead luminaire 10W in die-cast aluminium alloy/ PVC body heat resistant prismatic glass cover, with specially designed gasket for minimum IP 55 degree of protection complete all as specified and directed by Engineer-in-Charge. 134 Supply and fixLED building security light fitting 35 watts, Luman efficacy of LED 140 lm/W, PF>0.95 THD<10%, colour temperature 6500K CRI > 7, system luman not less then 2600 lm, made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens with toughed glass having bottom separate driver compartment with IP 65 protection and impact resistant of IK 07 etc and all accessories previewed complete including mounting bracket of GI Pipe 40mm inner dia light grade of reqd length and shape including bending, forging or welding etc and suitable bolts and nuts with washers, including connecting with PVC insulated multistandered cooper flexible cable of size 0.5sqmm 3 core form celling rose to fitting all as specified and directed. Notes:- (i) The rate of three core twisted flexible copper conductor cable of suitable size for connection is included in this item and noting shall be paid extra on this account.(ii) Warranty for replacement of each LED lite fitting shall not be less than 2 years from the date of purchase.(iii) Date of purchase shall be marked on each fixture with permanent marker for redeeming warranty benefits. 135 Supply and fix electric water heater, storage type steel body with Strainless Steel inner tank and heating element upto 2 KW Capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc. 136 S&F of ceiling fans complete with blades, down rods, (with remote) and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value more than 6.00 BEE. Five star rated with brushless direct current motor (BLDC) all as specified and directed by Engineer-in-Charge. 137 Supply and fixof modular MCB protected plug and socket board in sheet steel enclosure with 25A rated mini MCB and 20A rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket boardall as specified and directed. 138 Taking down unserviceable VTPN/ TPN DB with MCB"s of any make/ capacity complete all as specified and directed by Engr-in-Charge. 139 S&F of MCCB / MCB distribution board, Vertical TPN, 4 way, 415 V, 3 phase, AC with MCCB as incomer and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surfacecomplete all as specified and directed.Note: MCCB / MCBs shall be measured and paid separately. 140 Taking down unserviceavle Sheet metal box & MCB DB SPN with MCB"s of any make/capacity complete all as specified and directed by Engr-in-Charge. 141 Supply and fixof MCB distribution board, SPN, 8 way, 230 V, 1 phase, AC with MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB complete all as specified and directed. Note: MCCB / MCBs shall be measured and paid separately. 142 Supply and fixof MCB distribution board, SPN, 4 way, 230 V, 1 phase, AC with MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB complete all as specified and directed. Note: MCCB / MCBs shall be measured and paid separately. 143 S&F of MCCB, 63A, 16 KA, 4 Pole 415 V, 50 Hz with fixed thermal magnetic release complete all as specified and directed. 144 S&F MCB TPN 63 Amps, 10 KA, "C" Curve, 415 V, 50 Hz complete all as specified and directed. 145 S&F MCB SPN 40-63 Amps, 10 KA, "C" Curve, 230 V, 50 Hz complete as specified and directed. 146 S&F MCB SP 6 to 32 Amps, 230 V complete all as specified and directed. 147 Taking down old unserviceable of LT cable of any size complete all as specified and directed by Engr-in-Charge. 148 Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or strip and overall PVC sheathed, 16 sq mm 4 core ISI Marked as per IS 7098(Part 1) including connecting on LT panel based with suitable lugs, glands etc complete all as specified and directed. 149 Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or strip and overall PVC sheathed, 16 sq mm nominal cross section , 2 core in service connections as per IS 7098 (Part 1) including connecting on LT OH line / LT panel ? DB with suitable lugs, glands, binding wire etc. 150 Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etcfor protection of LT cable XLPE grade 1100 volts complete all as specified and directed by Engineer-in-Charge. 151 M&L for earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to GI wire 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed included taking down existing earthing complete.Note :- (i) The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth wire up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II. (ii)Contract must ensure earthing test result less than 5 Ohm and submitted test report to Engr-in-Charge. 152 Provision of composite rain water harvesting system including construction of underground water storage tank of 6000 Ltrcapacity built in brick masonry with following units(i) First flush system 01 Set(ii) Gravity Filter 01 PC(iii) Delivery pipes 25mm size -15 mtr (iv) Down take pipes 100mm size -15 mtr 153 Supply,laying and testing,galvanised iron pipe medium grade 25 mm diawith all fittings such as tee,bends,elbow,sockets, reducer,union etc of midium grade ISI marked fixed to walls/floorsceling in trenches including grove cutting for concealed plumbing and making good the dameged surfaces complete for the following bore :- Make Jindal/TATA/Prakash 154 Supply and fixing in replacement cast iron sluice valves both ends flanged, confirming to IS – 14846 of 2000 duly ISI marked, PN-1.6 complete with stainless steel spindle and gun metal nut including making 2 Nos flanged joints and also providingrubber gasket for GI pipe of bore 80 mm 155 Material and labour for brick masonry valves pit chamber (in non expansive soil) 1050mmx1050mmx1050mm including necessary excavation, PCC foundation / floors /coping, brick work, plastering andMS sheet cover of6 mm thick including and locking arrangement with two coats of enamel paint over a coat of redoxide primer all as directed 156 Sypply and fixing submersible open well electric driven 415 V , TP suitable for 50 mm dia and installed complete upto 5 WHP inclusive of 30 mtrs long submersible cable and starter. 157 Supply and fixing of gun metal globe/gate valves 25 mm diawith iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 158 Digging of holes in ordinary soil and refilling the same with excavated earth mixed with manure or sludge in the ratio of 2:1 by volume(2 part of stacked volume of earth after reduction by 20%, 1 part of stacked volume of manure after reduction by 8%) flooding with water ,dressing including removal of rubbish and surplus earth if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately Holes 0.60 m dia and 0.60 m deep. 159 Supplying and stacking of cowdung manure at site including royalty and carriage with all leads and lifts (manure measured in stack will be reduced by 8% for payment) 160 Supplying Chemical emulation in sealed container including delivery as specified.Chloropyriphose emulsifiable concentrate of 20% E.C 161 S and F mild steel frammed work as in tree guards complete including febrication, welding , revetting etc. 162 Plantation of plant name -BOUGAINVILLEA Ht. 4" insize Poly bags 163 All as above but plant nameKachnar (Bauhinia Variegata) 4’ in size Poly bags 164 All as above but plant name - Kaner (Thevetia Peruviana) in 4" size Poly bags 165 All as above plant name- Gardania (Cap Jasmine) 4" size Poly bags 166 All as above plant name - Gurhal (Hibiscus rosasinensis) Poly bags 167 Maintenance of space (other than the area where plantation is done) byde weeding, Grass/clearance,uprooting of vegetation jungles etc all completely without disturbing existing plants and disposal of the same on the low laying area in proper way as per EIC instructions (the cost of consumable, tools etc to be arranged by the Contractor) 168 Repair to pot holes any depth, not exc 1.0 sqm each includingsweeping free from dust and mud, or water, scoring sunken surfaces in roads , paths etc. cutting around edges to at least 25mm in depth making good by applying tack coat @ 5 kg per 10 sqm, putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 kg per 10 sqm blinded with 0.09 cum of stone, chippings, 6.3 mm size and again rammed (including supply of premixed macadam, binder and chippings) depth of potholes exc 30 mm complete all as specified and directed. 169 M&L for preparing black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surfaces with gunny gags to remove all loose dirt etc and applying evenly a priming/tack coat with bituminous primer at 5 kg per 10 sqmusingpaving bitumen VG-10complete all as specified and directed. 170 M&L forprovidingbituminous premixed asphaltic semi dense concrete (design mix) 30mm consolidated thickness using paving bitumen VG-30 @ 5.5% binder content by weight of total mix, laid/spread uniformly by means of mechanical pavers over primed black top surfaces rolled and compacted to required camber and gradient using 10 to 12 tonne power roller, complete all as specified and directed complete all as specified and as directed. 171 M& L, Premix bituminous, macadam with 4% binder content by wt of total mix usingpaving bitumen (VG-30) any penetrationlaid/rolled and compacted to required gradient and camber (consolidated thickness 75mm or less) ),as level correction. complete all as specified and as derected by Engr-in-Charge. 172 S&F in repair cat eye solarreflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions, complete all as specified and directed. 173 S&F in repair solar stud cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/0.3 watt one NI-ed rechargeable battery (1.2V/1600MA) consisting of super bright LED with10,000 to 18,000 mcd completed as per manufactures instructions etc, complete all as specified and directed. 174 M & L for preparing bituminous surfaces of road and marking 2.5mm thick center or edge line, stop lines, dashes, arrows, etc and the like n exc 10 cm wide hot applied thermo plastic road marking paint (reflective type ) of uniform finishing with machine conforming to BS 3262 (Part-I) 1989 read with most specification of 803 clause 4.2.1 and 4.2.2 on bituminous surface in white / yellow/ red colour and super imposed with glass slam beats conforming to BS 6088 and most specification 803 clause 4.3.3 including cleaning of surface by removing all dust dirt oil grease etc including removing of existing marking with spirit / kerosene / gas burner or mechanically on bituminous surface complete all as specified and directed. 175 M&L for 100mm thick (spread thickness) moorum/red bajri brought from out side MD land, filling in layers not exceeding 10cm thick, spread watered , rolled and consolidated with 8 to 12 tonne power roller to required camber and gradient, complete all as specified and directed.
|
