Tender For New Oxygen Plant Operators Room Construction Works in India

Work Detail

Tender For New Oxygen Plant Operators Room Construction Works - 1 Demolishing of Brick work 2 Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar 3 Demolishing of RCC 4 Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge. 5 Earth work excavation 6 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil 7 Earth work excavation for plinth beam 8 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil 9 soling 10 Soling with rough stone of size 200 mm, well packed and filling voids with stone chips and required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete. 11 Shoring 12 Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete (Measurements to be taken of the face area timbered).Depth not exceeding 1.5m 13 Dewatering 14 Bailing out water/slush using pump above 5HP and up to 10 HP, including conveyance to site and erection, cost of fuel, lubrication oil and other stores, pay of staff etc complete. All deposits/slush shall be shifted to designated location with in 1km lead 15 PCC 16 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) 17 Shuttering for footing 18 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete 19 RCC work up to plinth level 20 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources) 21 Reinforcement steel work up to plinth level 22 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelMild steel and Medium Tensile steel bars 23 Solid block work up to plinth level 24 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete 25 Bituminous painting 26 Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade:Two or more coats on new work 27 Filling Contractors earth 28 Filling with contractors own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge 29 Filling available earth 30 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. 31 Shuttering for columns above plinth level 32 Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts 33 Shuttering for Beams 34 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers 35 Shuttering for sunshade 36 Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges 37 Shuttering for slab 38 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform 39 Shuttering for stair 40 Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases) 41 RCC work for column aboveplinth level 42 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 43 RCC for slab, beam, lintel and sunshade 44 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15°landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). 45 Solid block work above plinth level 46 Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete 47 Plastering work 48 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 49 Ceiling Plastering 50 12 mm cement plasterof mix:1:3 ( 1 cement : 3 fine sand) 51 Terrace plastering 52 Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge. Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt meta instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).12 mm average thickness. 53 Aluminium Frame work for Doors windows and partitions 54 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) 55 Aluminium works for shutters of Doors and Windows 56 For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) 57 Uv sheet for doors and partition 58 Providing and fixing 4 mm thick UV sheet in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws , UV Sheet finished in two diffrent colours and complete as per architectural drawings and directions of Engineer - inCharge 59 Glass 60 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost ofaluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 61 Lock for doors 62 Providing and fixingBrass100 mm mortice latch and lock with 6 levers without pair of handles( best make of approved quality ) for aluminum doors including necessary cutting and making good etc. complete 63 Hinges 64 Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:100x58x1.90 mm 65 Handles 66 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:100 mm 67 Tower bolts 68 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : (Copper oxidized as per IS : 1378)250x10 mm 69 FRP door frame 70 Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of crosssection 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. 71 FRP door shutters 72 Providing and fixing to existing door frames.30 mm thick Fiberglass Reinforced Plastic (F.R.P) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used all filler material throughout the hollow panel, casted monoolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS : 14856, complete as per direction of Engineerin-charge. 73 Tiling work- Floor 74 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), with spacers for epoxy joint fillers(epoxy filling shall be paid extra) complete.Size of Tile 600 x 600 mm or larger size 75 Anti skid floor tile 76 Providing and fixing premium quality ceramic digital anti-skid floor tiles of make; Kajaria /Nitco/ Simpolo/Cera or approved brand conforming to IS : 15622 (thickness to be ; specified by the manufacturer), in all colours, shades of size matching to wall tiles or as approved by;Engineer -in-Charge, over 12 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) with tile spacers and jointing with epoxy joint fillers with colour of matching shade of approved brand in approved pattern;with two or more desgin tiles complete. 77 Wall tile 78 Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, ofapproved make, in all colours, shade, in toilet walls, skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), with spacers for epoxy joint fillers(epoxy filling shall be paid extra) complete.Size of Tile 600x600 mm or larger size 79 Epoxy Grouting at tile joints 80 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm 81 Paintingwork 82 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) 83 Scrapping and papering 84 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 85 water proof for toilet area 86 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. mm 87 Window grill 88 Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc 89 SS handrail 90 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) 91 Steel anchoring work 92 Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make including scaffolding upto 4 m height but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge.Upto and including 12mm dia. 93 25 mm PVC concealed 94 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 10kgf /cm2 95 50 mm PVC Concealed 96 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2 97 63 mm PVC Concealed 98 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2 99 32 mm pvc pipe exposed on wall 100 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 6 Kgf/cm2 - External work - Exposed on wall 101 50mm pvc pipe exposed on wall 102 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6Kgf/cm2 - External work - Exposed on wall 103 110mm pvc pipe trenching and refilling 104 Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2 105 63mm dia elbow 106 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow 107 63mm 45 degree elbow 108 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipesincluding jointing with PVC solvent cement -63 dia 45 degree Elbow 109 63 dia pvc door elbow 110 Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Door Elbow 111 63 dia tee 112 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes including jointing with PVC solvent cement - 63x63x63 mm dia Tee 113 63mm dia pvc bend 114 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend 115 63mm dia door tee 116 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63x63x63 mm dia Door Tee 117 63mm dia vent cowl 118 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia vent cowl 119 110-63mm pvc reducer 120 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110x63 mm dia Reducer 121 63x50mm pvc reducer 122 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63x50 mm dia Reducer 123 63mm dia socket/coupling 124 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia socket/coupling 125 110mm dia elbow 126 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow 127 110mm dia 45 degree elbow 128 Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow 129 110 mm dia door elbow 130 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow 131 110mm dia bend 132 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend 133 110mm dia tee 134 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee 135 110mm dia door tee 136 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x110 mm dia Door tee 137 110mm dia socket/coupling 138 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling 139 GM ball valve 140 Providing and fixing GM ball valve of approved quality (screwed end) :25 mm nominal bore 141 Providing and fixing CP brass bib cock long body 142 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore 143 Providing and fixing CP brass stop cock 144 Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore 145 CP brass angle valve 146 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore 147 PVC ball valves 148 Providing and fixing PVC ball valve (ISI marked) of approved brand for Rigid PVC pipes, including jointing with PVC solvent cement: ;25mm nominal bore. 149 CP brass shower rose 150 Providing and fixing C.P. brass shower rose with arm of 15 or 20 mm inlet: ;100 mm diameter 151 SS soap Dish 152 Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. 153 Towel rod 154 Supplying and fixing CP Towel rod 45cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-incharge. 155 Health faucet 156 Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge. 157 CP gratings 158 Providing and fixing CP grating of approved quality.;Rectangular type with openable circular lid;150 mm nominal size square 100 mm diameter of the inner hinged round grating 159 Floor trap 160 Providing and fixing PVC moulded Floor trap for sanitary pipelines, including jointing PVC pipes with PVC solvent cement and filling gaps with cement groutFloor trap 4 way/3 way 161 Providing and fixing european type water closet 162 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid 163 Providing and fixing wash basin 164 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap 165 Providing and fixing mirror 166 Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm 167 Supply of3 phase 40 A,4 way Horizontal Distribution boards 168 Supply of3 phase 40 A,4 way Horizontal Distribution boards in sheet steel enclosure with double door and detachable gland plate, complete withcable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required, with 40A 30 mA RCCB as incomer & 8 Nos 6A SP MCB and 2 NosSP 20A MCB as outgoings and 2 dummy plate. For Concealed Flush mounting.Make: Standard/Havells/ABB/Siemens/Hager/ Schneider 169 UTP/Ethernet Cat 6 cable 170 UTP/Ethernet Cat 6 cable, Make: D-link, Finolex, Polycab, Lapp 171 Telephone cable 172 Telephone cable, twin flat copper PVC insulated, 2 x 0.5 sq mm, ISI marked, Make: Finolex, Anchor, V-guard, Traco, Sark, Orbit, Polycab 173 Supply ofLED downlight round(165mm dia approx), 12W 174 Supply ofLED downlight round(165mm dia approx), 12W (Approximate), 230V, 50Hz AC supply, with spring buckle for concealed false ceiling mounting, Lumen efficacy: 90 Lumens/W or above, Lumens: 810 Lumens or above, THD: 15% or less, PF: 0.90 or above, CRI: 80 or above, Colour temperature: Cool White(5500-6500K), IP: 20 or above, Warranty: Full warranty of 1 year or above 175 Supply of LED light for bathroom 9W 176 Supply of LED light for bathroom 9W (Approximate), 230V, 50Hz AC supply, with spring buckle for concealed false ceiling mounting, Lumen efficacy: 90 Lumens/W or above, Lumens: 700 Lumens or above, THD: 15% or less, PF: 0.90 or above, CRI: 80 or above, Colour temperature: Cool White(5500-6500K), IP: 20 or above, Warranty: Full warranty of 1 year or above 177 Supply of6A switch 178 Supply of6A switch, for 1 module, modular, Make: Legrand, Anchor, ABB, Honeywell 179 Supply of 25A switch 180 Supply of 25A switch, for 1 module, modular, Make: Legrand, Anchor, ABB, Honeywell 181 Supply of 16A switch 182 Supply of 16A switch, for 1 module, modular, Make: Legrand, Anchor, ABB, Honeywell 183 Supply of 6ASocket 184 Supply of 6ASocket, for 2 module, modular, Make: Legrand, Anchor, ABB, Honeywell 185 Supply of16A Socket 186 Supply of16A Socket, for 2 module, modular, Make: Legrand, Anchor, ABB, Honeywell 187 Supply of25A Socket 188 Supply of25A Socket, for 2 module, modular, Make: Legrand, Anchor, ABB, Honeywell 189 Supply of RJ11 Socket 190 Supply of RJ11 Socket, for 1 module, modular, Make: Legrand, Anchor, ABB, Honeywell 191 Supply of RJ45 Socket 192 Supply of RJ45 Socket, for 1 module, modular, Make: Legrand,Anchor, ABB, Honeywell 193 Supply of Concealed box, Plate and frame for 2 module, 194 Supply of Concealed box, Plate and frame for 2 module, modular, Make: Legrand,Anchor, ABB, Honeywell 195 Supply of Concealed box, Plate and frame for 3 module 196 Supply of Concealed box, Plate and frame for 3 module, modular, Make: Legrand, Anchor, ABB, Honeywell 197 Supply of Concealed box, Plate and frame for 4 module 198 Supply of Concealed box, Plate and frame for 4 module, modular, Make: Legrand, Anchor, ABB, Honeywell 199 Supply of Concealed box, Plate and frame for 6 module 200 Supply of Concealed box, Plate and frame for 6 module, modular, Make: Legrand, Anchor, ABB, Honeywell 201 Supply ofConcealed box, Plate and frame for 9 module 202 Supply ofConcealed box, Plate and frame for 9 module, modular, Make: Legrand, Anchor, ABB, Honeywell 203 Supply of materials required for copper point wiring 204 Supply of materials required for copper point wiring for lights, fans in PVC conduit with modular type switch - using 1.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq. mm. PVC insulated copper wire as required, to complete. (Excluding supply of Fans, Exhaust fans, Lights, Concealed mounting boxes, Plates and Frames, Switches etc (Approximate 5 meters/point) 205 Supply of materials required for copper point wiring 206 Supply of materials required for copper point wiring as 102.01 above for more than 5 meters. 207 Supply of materials required for copper circuit wiring in PVC conduit 208 Supply of materials required for copper circuit wiring in PVC conduit - with 2.5 sq.mm. PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no. 2.5 sq. mm. PVC insulated copper wire for loop earthing as required. 209 Supply of materials required for copper circuit wiring in PVC conduit 210 Supply of materials required for copper circuit wiring in PVC conduit - with 1.5 sq.mm. PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no. 1.5 sq. mm. PVC insulated copper wire for loop earthing as required. 211 Installation, testing and commissioning of LED downlight light 212 Installation, testing and commissioning of LED downlights of all types complete with all accessories etc. including connection with 1.5 sq.mm PVC insulated copper conductor single core cable etc. as required. 213 Installation, testing and commissioning of LED tubelight lights/ lamps 214 Installation, testing and commissioning of LED tube light/ lamps of all types complete with all accessories etc. including connection with 1.5 sq.mm PVC insulated copper conductor single core cable etc. as required. 215 Installation of ceiling fans & exhaust fans 216 Installation of ceiling fans & exhaust fans making connections, testing and commissioning etc. with 1.5 sq.mm PVC insulatedcopper conductor single core cable etc. as required 217 Installation, testing and commissioning of Smoke Detectors 218 Installation, testing and commissioning of Smoke Detectors complete with all accessories. 219 Fixing of 6/16/25 amps modular type sockets, switches 220 Fixing of 6/16/25 amps modular type sockets, switches, RJ11 and RJ45 modular sockets with front plate in surface or in recess including providing and fixing suitable size metal box, inter connections etc as required. 221 Copper point wiring in PVC conduit with modular type switch 222 Copper point wiring in PVC conduit with modular type switch - Wiring for light point/fan point/exhaust fan point using 1.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outerplate) in suitable metal boxes etc. as required to complete. 223 Supply of materials required for copper point wiring(for Above item for more than 5 meters) 224 Copper point wiring as item.111 above for more than 5 meters. 225 Circuit Wiring with 2.5 sq.mm 226 Copper circuit wiring in PVC conduit - Circuit Wiring with 2.5 sq.mm PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no. 2.5 sq. mm. PVC insulated copper wire for loop earthing as required. 227 Copper circuit with 1.5 sq.mm 228 Copper circuit wiring in PVC conduit - Circuit Wiring with 1.5 sq.mm PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no. 1.5 sq. mm. PVC insulated copper wire for loop earthing as required. 229 LANwiring in PVC conduit 230 LANwiring in PVC conduit - Circuit Wiring with UTP/Ethernet cable in recessed PVC conduit as required.. 231 Telephone wiring in PVC conduit 232 Telephone wiring in PVC conduit - Circuit Wiring with two core telephone cable in recessed PVC conduit as required. 233 Installation, Testing and Commissioning (Concealed Flush mounting) of 40A, 3 phase 4 way Vertical Distribution board 234 Installation, Testing and Commissioning (Concealed Flush mounting) of 40A, 3 phase 4 way Vertical Distribution board In sheet steel enclosure with double door and detachable gland plate, complete withcable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required along with fixing of 40A, 30mA RCCB as incomer and 8 No.s of 6A SP MCBs and 2 No.s of 20A SP MCBs as outgoings 235 Laying, dressing and clamping of following cables through exsistingtrays / structures / racks / columns 236 Laying, dressing and clamping of following cables through exsistingtrays / structures / racks / columns etc to the new DB .Cable shall be supplied by KMML.All other materials required for clamping are under the scope of contractor.3.5 x 16sq. mm AYFY/XLPE cable 237 Glanding and termination at DB"s 238 Glanding and termination at DB"sside ofPVC cable using DC glands/ lugs including supply of cable glands, lugs, aluminium crimping sockets, nuts bolts etc. required for this work.Gland earthing as per standards shall be done by the contractor. 3.5 X 16 Sq. mm cable 239 Preparation of all electrical drawings 240 Preparation of all electrical drawings and obtaining statutory approval from electrical inspectorate for the new DB. 241 Labour charge 242 Misc. Labour charge

Contact Information