|
Supply Of Furniture For Extension Or Construction Of Boys Hostel No 4 Block-C Supply Of Furniture For Extension Or Construction Of Boys Hostel No 4 Block-C , Supply Of Beds As Per Specification Given As Under:1.The Overall Size Of The Bed Should 74”X37”X18”. 2. The Frame-Work Should Be Made Of M.S. Rectangular Pipe 25X50mm, 16G Constitution The Rectangle Of The Sleeping Surface Supported Over Four Legs Made Of 40X40mm M.S. Pipe, 16G, Suitably Strengthened At Corners By 25X25x16g Pipe. The Dimensions Of Sleeping Surface (Sleeping Rectangular) Are 72”X35”. 3.There Should Be Five No. Supports Of 25X25x16g Pipe For Bed On Shorter Side. 4. The Sleeping Surface Should Consist Of Isi Mark 15Mm Thick Commercial Plywood Sheet Fixed In The Metal Frame. Make:- Venus/Marino/Greenply-Ecotech/Duro Tower/Sainik By Century Ply. 5.The Bed Should Be So Designed That The Mattress Is Held In Position By Specially Raised Edges On All Sides Inbuilt In The Metal Frame So As To Prevent Slipping Of Mattress. 6. The Bed Should Be Equipped With A Head-Rest Made Of Square Pipe 25Mm, 16G Bent Into A Round Shape At The Corners 270Mm Above The Sleeping Surface And Cladded With A Both Sides Pre-Laminated Board 18Mm Thick Of Isi Mark. 7. All Steel Parts Should Be Cleaned Deserted And One Coat Of Metal Primer And Deco Spray Paint Matt Finish Be Provided. 8. The Legs Should Be Equipped With Good Quality Rubber Shoes To Prevent Scratches On The Floor. , Supply Of Study Table As Per Specification Given As Under:1. Size Of Study Tables Must Be 3’X2’ And 2’-6” High Made Of M.S Pipe 16G, 25X25mm, 25X50mm Constituting And Support System Of The Table As Per Sample/Drawing. 2. The Table Top Must Be One Side Laminated, 18Mm Thick Hdf Board (Make: Action-Tesa/Green Board/Asian Prelam) Front Side With Post Forming And The Remaining Three Sides Are Protected With Pvc Lipping Fixed With Hot Melt Glue. 3. The Table Must Be Equipped With A Metal Drawer Made With 20Gauge M.S. Sheet With The Size Of Outer Body 12”Width X18” Depth X5” Height. The Drawer Inner Dimensions Should Be 9.5” (W) X 15.5” (D)X 2.5”(H). The Drawer Should Move On Good Quality Telescopic Sliding Channels. 4. The Legs Should Be Equipped With Good Quality Rubber Shoes To Prevent Scratches On The Floor. 5. There Should Be A Leg Rest Made Of M.S Pipe 25X50mm Of 16G Thickness. 6. All Steel Parts Should Be Thoroughly Pre-Treated For Degreasing, Derusting One Coat Of Metal Primer, Deco Spray Paint Matt And Pretreated In 4-Step Ant-Corrosion Treatment (Degreasing, Pickling, Phosphating, Passivation) Before Being Powder Coated And A Baked In Oven So As To Achieve 45-50 Micron Thickness Of The Powder And A Complete Scratch Resistant Surface And Superb Finish Surface Of The Approved Shade Be Provided. , Supply Of Study Chair As Per Specification Given As Under: Study Chair Having Seat Front Height 45Cms. And Back Height 80Cms. The Seat Size 405X405mm Is Made Out Of 18G Perforated Sheet, Nicely Contoured In Front And Curved At Back. The Seat Is Welded On 19Mm X 16G Pipe Frame Curvatures Must Also On Top And P Shaped Sides To Provide Strength And Rigidity To The Frame Structure. The Perforated Back Which Is Welded To Pipe Frame Must Also Be In 18G. The Chairs Are Stackable And Are To Be Provided With Synthetic Shoes Screwed At The Bottom For Smooth Movement On Floor. All Steel Parts Shall Be Pretreated In 4-Step Ant-Corrosion Treatment (Degreasing, Pickling, Phosphating, Passivation) Before Being Powder Coated And A Baked In Oven So As To Achieve 45-50 Micron Thickness Of The Powder And A Complete Scratch Resistant Surface And Superb Finish Nylon Level Adjusted. The Seat Height Should Be 45 Cms. In The Front And Sloping Downwards By About 1 Cm. Towards The Rear. (Weight Of Chair Should Be Minimum 6.25Kg ± 0.25Kg. Each) , Supply Of Study Chair As Per Specification Given As Under: Study Chair Having Seat Front Height 45Cms. And Back Height 80Cms. The Seat Size 405X405mm Is Made Out Of 12Mm Thick Hot Pressed Commercial Plywood Padded With Foam Of 30Mm Thickness, 32 Kg/Cum Density, Nicely Contoured In Front And Curved At Back. The Chair Shall Be Made With 19Mm X 16G Crce Pipe Chorme Plated Of 55-60 Micron Frame. Curvatures Must Also On Top And P Shaped Sides To Provide Strength And Rigidity To The Frame Structure. The Back Shall Also Be Made With 12Mm Hot Pressed Commercial Plywood Moulded In Curved Shape Padded With Foam Of 30Mm Thickness 32Kg/Cum Density Fixed To Pipe Frame. Seat And Back Shall Be Upholstered With Leatherette Tapestry 1Mm Thick And 570 Gsm. The Chairs Are Stackable And Are To Be Provided With Synthetic Shoes Screwed At The Bottom For Smooth Movement On Floor. All Steel Parts Shall Be Pretreated In 4-Step Ant-Corrosion Treatment (Degreasing, Pickling, Phosphating, Passivation) Before Being Chorme Polish So As To Achieve 55-60 Micron Thickness A Complete Scratch Resistant Surface And Superb Finish Nylon Level Adjusted. The Seat In The Front Shall Sloping Downwards By About 1 Cm. Towards The Rear Complete In All Respect. , Supply Of Stainless Steel Table For Dining Hallas Per Specification Given As Under: Dining Table Of Size 92” X 44” And Height 30”. Top: Top Made Of Stainless Steel Sheet 16G 304 Grade Size 92” X 44” Bent On All Four Sides To Remove Sharp Edges. Framework: Top Frame Made Of 50 X 25Mm X 16G Pipe Of Size 90” X 42”. There Will Be Three Extra Supports Of Pipe 50 X 25Mm X 16G Of Smaller Length. Legs Will Be Made From 40 X 40Mm X 16G Pipe 30” High. Bottom Support All Around Made Of Pipe 50 X 25 X 16G. All Pipes Used Will Be Of Stainless Steel 304 Grade. Synthetic Shoes Of Good Quality With Metal Plate Will Be Provided At The Bottom Of Legs. , Supply Of Reading Tableas Per Specification Given As Under: Reading Table Size 1800Mm X 1200Mm X 750Mm Frame Made Of Crca Tube & Pipe Of 50Mm X 25Mm & 25Mm X 25Mm Of 16G, Legs Made Of 40Mm X 40Mm X 16G As Per Design. Top Made Of 25Mm Pre-Laminated Particle Board (Make: Action-Tesa/Green Board/Asian Prelam), Post Formed On Two Longer Sides, Having One Partition In The Upper Middle Fitted With Snow Glass In A Box. Height Of Top Partition Will Be 450Mm And One Shelf 300Mm Wide Below Table Top At A Height Of 250Mm From Top. Leg Rest Will Be Given Of 50Mm X 25Mm X 16G Pipe. All The Balance Open Sides Of P.L.B. Will Be Covered With 1.5Mm Thick Pvc Moulding Of Matching Shade Fixed With Hot Melt Glue. All The Iron Structure Will Be Made From Crca Pipe Of Tata/Jindal Make. All The Metal Parts Should Be Thoroughly Pre-Treated For Degreasing, Derusting, One Coat Of Metal Primer, Deco Spray Paint Matt And Pretreated In 4-Step Ant-Corrosion Treatment (Degreasing, Pickling, Phosphating, Passivation) Before Being Powder Coated And A Baked In Oven So As To Achieve 45-50 Micron Thickness Of The Powder And A Complete Scratch Resistant Surface And Superb Finish Surface Of The Approved Shade Be Provided.
|
