|
Rate Contract For Standard Furniture And Partitions Rate Contract For The Supply And Installation Of Customized Modular And Standard Furniture And Partitions At High Court And Subordinate Courts In The State Of M.P. , Section A (Workstation) , Workstation (Panel Based) With Prelaminated Top , Providing & Fixing In Position Modular Workstation Having Partition Height From 1135 - 1200Mm Having Thickness Of 54Mm +/-6Mm. Partition Panel Consists Of Framework Made Of 1.5Mm Thick Aluminum And Would Be Finished By Aluminum Alloy Extrusions Of 1.2-2.1Mm Thickness 50-58 Mm X 12- 17Mm Of Matching Height Of The Panel And A Top Runner Of Powder Coated Aluminum Extrusions 54Mm +/6Mm X 12- 13Mm X 1.2 To 2.1Mm Thick. Further The Frame Work Should Consist Of An Infill Structure Of Batten Of Size 40-50X25-40Mm Particle Board Honey Comb Inside. The Outer Layers Shall Be Made Of Mdf/Ppb Of 3- 4Mm Thickness And Finished With Decorative Laminated Sheets Of 0.6 -1.0Mm Thickness Having One Side Bearing The Decorative Surface For Bottom Panel & Fabric For Top Panel. The Total Block Thus Would Be Of 44-54Mm Thickness. This Shall Be Attached To Top Panel By Means Of Self Tapping Screws. All Steel Parts Shall Be Pretreated For Seven Stages Anti Corrosion Treatment Followed By Epoxy Powder Coating. Height Of Skirting Shall Be 85 To 150Mm. One Intermediate Raceway To Be Provided Below Or Above The Worktop As Decided By The Officer-In-Charge In Which Provision Of One Electrical Switch Of Three Sockets Is To Be Fixed By The Bidder Of Reputed Make Like Cona/ Wipro/ Philips/ Avells/Honeywell/ Anchor Or Equivalent Brand Of Repute In The Modular Furniture After Drawing Approved By The High Court. Partition To Be Supported By Stability Brackets Wherever Required. Workstation Consists Of Work Surface Of 25Mm Thick Prelaminated Particle Board Having Pvc Edge Lipping Of 2Mm Thick On All Exposed Edges And 0.6Mm On All Butt Edges & Pressed At 200O C With Hot Melt Glue On Edge Banding Machines. The Worktop Shall Be Supported By Cantilever/ Brackets Made Of Ms Steel Duly Powder Coated. The Workstation Shall Also Be Provided With Name Plate Holder In Acrylic Of Approx Size 230X75mm. The Workstation To Be Made In Following Sizes And Configuration As Per Sizes And Details Given. , Type A , H Module With Rectangular Work Surface Of Size 1200X600mm (2 Person) , T Module With Rectangular Work Surface Of Size 1200X600mm (2 Person) , U Module With Rectangular Work Surface Of Size 1200X600mm (1 Person) , L Module With Rectangular Work Surface Of Size 1200X600mm (1 Person) , H Module With Rectangular Work Surface Of Size 1350X600mm (2 Person) , T Module With Rectangular Work Surface Of Size 1350X600mm (2 Person) , U Module With Rectangular Work Surface Of Size 1350X600mm (1 Person) , L Module With Rectangular Work Surface Of Size 1350X600mm (1 Person) , Type B , H Module With Trapezoidal Work Surface Of Size 1200X600/750Mm (2 Person) , T Module With Trapezoidal Work Surface Of Size 1200X600/750Mm (2 Person) , U Module With Trapezoidal Work Surface Of Size 1200X600/750Mm (1 Person) , L Module With Trapezoidal Work Surface Of Size 1200X600/750Mm (1 Person) , H Module With Trapezoidal Work Surface Of Size 1350X600/750Mm (2 Person) , T Module With Trapezoidal Work Surface Of Size 1350X600/750Mm (2 Person) , U Module With Trapezoidal Work Surface Of Size 1350X600/750Mm (1 Person) , L Module With Trapezoidal Work Surface Of Size 1350X600/750Mm (1 Person) , Type C , Curvilinear Module 1800X1500x600mm (For One Person) , Curvilinear Module 1500X1500x600mm (For Two Persons) , Curvilinear Module 1500X1500x600mm (For Four Persons) , Curvilinear Module 2100X1800x600mm (For One Person) , Curvilinear Module 1500X1350x600mm (For Two Persons) , Curvilinear Module 1500X1350x600mm (For Four Persons) , Providing & Fixing In Position The Add-On Partition To Increase The Height Of Workstation Partitions From 1200 To 1650. The Specification And Partition System To Be Same As Low Height Partition As In Item No. 1.1. , Workstation (Tile Based) With Post Formed Top , Providing And Fixing Partition 60-70Mm Thick Having Inner Clear Space Of 40-52 Mm For Electrical Wiring. The Height Of Partition Should Be 1200-1250Mm. All Metallic Parts Shall Undergo A 7 Stage Antirust Treatment And Shall Be Powder Coated In Matt Finish To A Thickness Of 40-60 Microns. All The Hardware Items Should Be As Per Bifma/Ansi Standards. All Other Items As Per Is Standards. Modular Partition -The Modular Partitions Shall Not Be Grouted In The Floors. The Modular Partitions Shall Be An Assembly Of The Following Parts:-Levelers -Each Frame Shall Be Provided With Two 8-15Mm Leveling Bolts Which Allow 10-25Mm Adjustment For Floor Unevenness. Frames Shall Form The Basic Support Structure For All Other Components. The Main Vertical Member Of The Frame Bearing The Load Of Brackets And Storages Shall Be Made Of 1.5Mm Crca Steel. The Horizontal Members Shall Be Made Of 1.0Mm Crca Steel. The Thickness Of The Frame Shall Be 35-45Mm. Each Individual Module Shall Not Be More Than 1200Mm In Length. The Frames Shall Also Have Prefabricated Slots For Fixing Brackets Used To Support Worktops. Overhead Hampers, Gable Ends. Etc. All The Verticals & Horizontal Frame Shall Be Fixed With Nut & Bolts And Shall Not Be Welded. Skirting: The Frame Shall Have A Skirting Of 100-150Mm Height. The Skirting Shall Be Designed So That Switches Can Be Provided At The Skirting Level. The Skirting Shall Be Snap Fitted On Both Sides With Skirting Plates Made Of 0.8M Thick Crca Steel. Wherever Switches Are Provided On The Skirting Plates Shall Have The Necessary Slots. Post/Covers-The Frames Shall Be Connected At The Junctions By Aluminum Connectors. The Post Shall Be Made Of Aluminum Extrusions Of Minimum 1.2M Thickness. Trims-The Exposed Vertical And Horizontal Faces Of The Frames Shall Be Snap Fitted With Curve Trims. The Trims Shall Be Made Of Aluminum Extrusions Of Minimum 1.2Mm Thickness And 60-70Mm Width. Wire Management -Partitions System Shall Have Concealed Wire Management Capabilities To Meet Requirement And Technical Specifications And Shall Be Officered For Responsive And Fire Safe Operations Of Power, Telecommunications And Data (Lan) And Shall Have The Provision For Raceway At Bottom And Middle Level. , I. Separate Components For Electrical, Data And Telephone Cables Having Adequate Capability Of Both The Vertical And Horizontal Wire Movements. Ii. Slots Shall Be Provided On Frame To Fix All Electrical And Data Points. Iii. Storage For Excess Wires In The Partitions. Iv. Easy Access For Further Maintenance And Capacity For Additional Power, Data, Phone Point To The Panels Without The Need To Dismantle Work Surface. Tile Finish -The Partition Shall Have Tiles Made Up Of Laminate/ Fabric/ White Maker As Per Direction Of Officer-In-Charge With The Following Details: Laminated Tiles -The Laminated Tiles Shall Be Made Of Min. 9Mm Pre Laminate Plpb With Decorative Laminate On One Side And Balancing Lamination On Other Side. Fabric Tiles -The Fabric Tiles Shall Be Made Of Min 9Mm Soft Board Inside & Covered With Fabric Pasted On Them By Pva Glue. It Should Be Possible To Replace The Fabric By Peeling It Off. Workstation Consist Of Work Surface Made Of 25Mm Thick Post Formed Particle Board With 0.7Mm Decorative Laminate On Top & Balancing Laminate On Unexposed Face And Having All Exposed Edges Sealed With Pvc Edge Banding Tape. The Worktop Shall Be Supported With Cantilever Brackets Made Of Ms Steel Duly Powder Coated. Work Surface Shall Be Provided With Wire Manager To Carry Wires From The Bottom Complete As Per Salient Features, Specification, Drawing & Directions Of The Officer-In-Charge In Which Provision Of One Electrical Switch Of Three Sockets Is To Be Fixed By The Vendor Of Reputed Brand Like, Cona/ Wipro/ Philips/ Havells/ Honeywell/ Anchor Or Equivalent Brand Of Repute In The Modular Furniture After Drawing Approved By The High Court. The Workstation Shall Also Be Provided With Name Plate Holder In Acrylic Of Approx Size 230 X 75Mm. The Workstation To Be Made In Following Sizes And Configuration As Per Sizes And Detail Mentioned. , Type D , H Module With Rectangular Work Surface Of Size 1200X600mm (2 Person) , T Module With Rectangular Work Surface Of Size 1200X600mm (2 Person) , U Module With Rectangular Work Surface Of Size 1200X600mm (1 Person) , L Module With Rectangular Work Surface Of Size 1200X600mm (1 Person) , H Module With Rectangular Work Surface Of Size 1350X600mm (2 Person) , T Module With Rectangular Work Surface Of Size 1350X600mm (2 Person) , U Module With Rectangular Work Surface Of Size 1350X600mm (1 Person) , L Module With Rectangular Work Surface Of Size 1350X600mm (1 Person) , Type E , H Module With Trapezoidal Work Surface Of Size 1200X600/750Mm (2 Person) , T Module With Trapezoidal Work Surface Of Size 1200X600/750Mm (2 Person) , U Module With Trapezoidal Work Surface Of Size 1200X600/750Mm (1 Person) , L Module With Trapezoidal Work Surface Of Size 1200X600/750Mm (1 Person) , H Module With Trapezoidal Work Surface Of Size 1350X600/750Mm (2 Person) , T Module With Trapezoidal Work Surface Of Size 1350X600/750Mm (2 Person) , U Module With Trapezoidal Work Surface Of Size 1350X600/750Mm (1 Person) , L Module With Trapezoidal Work Surface Of Size 1350X600/750Mm (1 Person) , Type F , Pentagon L Module 1500X1500mm (For One Person) , Pentagon T Module 1500X1500mm (Shared Two Persons) , Pentagon + Module 1500X1500mm (Shared Four Persons) , Pentagon L Module 1800X1800mm (For One Person) , Pentagon T Module 1800X1800mm (Shared Two Persons) , Pentagon + Module 1800X1800mm (Shared Four Persons) , Providing & Fixing In Position The Add-On Partition To Increase The Height Of Workstation Partitions From 1200 To 1650. The Specification And Partition System To Be Same As Low Height Partition. , Desk Based Workstation , Providing & Fixing Desk Based System Overall Height 1150- 1175Mm With Top In 25Mm Prelaminated Particle Board In Curvilinear/ Linear Shape Having Main Post & Legs In Crca Steel Duly Powder Coated. The System Shall Have 25Mm Thick Prelaminated Particle Board/ Soft Board Between 2 Worktops. Below The Worktop Runs The Cable Tray In Steel Duly Powder Coated To Run The Cables. The Screen Shall Have Aluminum Extruded End Trims On Both Sides Of Screen. Height Of Screen Shall Be 600Mm & It Shall Be Projected 400Mm Above Worktop Level Of 750Mm Thereby Making Overall Height Of Workstation As 1150Mm. The Workstation Shall Have A Raceway Beam Panel Made Of Crca Steel In 0.8Mm Thickness Duly Powder Coated Shall Be Fixed Below The Worktop. It Shall Have Separator In Center To Segregate Power And Data Cables. It Shall Have Provision To Mount Electrical & Data Switches On It Face Above Or Below Work Top. The Workstation Shall Have Main Post Minimum 100Mm Wide And Shall Be Made Of Crca Steel Of 0.8Mm Thickness Duly Powder Co Ted. It Shall Be Covered With Board At The Top. Workstation Consists Of Work Surface Of 25Mm Thick Prelaminated Particle Board Having Pvc Edge Lipping Of 2Mm Thick On All Exposed Edges And 0.6Mm On All Butt Edges & Pressed At 200O C With Hot Melt Glue On Edge Banding Machines. The Workstation Shall Have Side Quarter Round Privacy Screen Made Of 25Mm Thick Prelaminated Particle Board Provided On Both Sides. The Workstation Shall Be Supported With Drawer Unit Having Overall Size 380X500x725ht. On One Side Leg Panel On The Other Side. Drawer Unit Shall Be Made Of 18Mm Prelaminated Particle Board With Inner Drawer In Steel Duly Powder Coated Moving On Nylon Rollers. It Consists Of One Drawer And One Open Able Shutter Below With Proper Locking Arrangement. The Workstation Shall Also Be Provided With Name Plate Holder In Acrylic Of Approx Sixe 230X75mm. The Workstation Should Have The Provision Of One Electrical Switch Of Three Sockets Is To Be Fixed By The Vendor Of Reputed Brand Like, Cona/ Wipro/ Philips/ Havells / Honeywell / Anchor Or Equivalent Brand Of Repute In The Modular Furniture After Drawing Approved By The High Court To Be Made In Following Sizes And Configuration As Per Sizes And Etail As Mentioned:- , Type G , Linear Main T Module 1200X600 - (For 2 Persons) , Linear Single Add-On Module 1200X600 (For 1 Persons) , Linear Main Plus Module 1200X600 -(For 4 Persons) , Linear Double Add-On Module 1200X600 (For 2 Person) , Type H , Curvilinear 1500X1500 Single Module (For 1 Person) , Curvilinear 1500X1500 T Module For (2 Persons) , Curvilinear 1500X1500 Plus Module For (4 Persons) , Cashier Counter Providing & Fixing Modular Cashier Counter 60-70Mm Thick Made Up Of Partition Of Height (2900 +/-300Mm Ht.) Having Crca Section Frame Work Having12mm Thick Plpb/Sb/Glass, Panels Having Bottom And Middle Raceway In Steel & Covers In Extruded Aluminum Section Duly Powder Coated And Abs Plastic Caps. The Front Cashier Panel Shall Be In Glass With Slit/Hole For Paper/Cash/Voice Interaction. One Intermediate Raceway To Be Provided Below Or Above The Worktop As Decided By The Officer-In-Charge. Partition To Be Supported By Stability Brackets Wherever Required. The Counter Is Provided With A Sharer Top Of Size 450Mm (D) & Work Surface Top Of 600 (D) In 25Mm Thick Post Formed Finish. The Worktop Shall Be Supported On One Vertical Support In 18Mm Prelaminated Particle Board. The Workstation Shall Also Be Provided With Name Plate Holder In Acrylic Of Approx Size 230X75mm. The Workstation To Be Made In Following Sizes And Configuration As Per Sizes And Detail As Mentioned:- , 1200X600 , 1350X600 , Full Height Partitions , Providing And Fixing Full Height Partition Thickness 60-70Mm Thick And Should Have Clear Space Of 40-52 Mm For Electrical Wiring. The Height Of Partition Should Be 2700Mm (Approx) Or Upto False Ceiling Height. All Metallic Parts Shall Undergo A 7 Stage Antirust Treatment And Shall Be Powder Coated In Matt Finish To A Thickness Of 40-60 Microns. All The Hardware Items Should Be As Per Bifma/Ansi Standards. All Other Items As Per Is Standards. Front/ Side Full Ht. Partition Modular Partition -The Modular Partitions Shall Not Be Grouted In The Floors. The Modular Partitions Shall Be An Assembly Of The Following Parts:-Levelers -Each Frame Shall Be Provided With Two 8-12Mm Leveling Bolts Which Allow 10-25Mm Adjustment For Floor Unevenness. Frames Shall Form The Basic Support Structure For All Other Components. The Main Vertical Member Of The Frame Bearing The Load Of Brackets And Storages Shall Be Made Of 1.5Mm Crca Steel. The Horizontal Members? Shall Be Made Of 1.0Mm Crca Steel. The Thickness Of The Frame Shall Be 68-75Mm. Each Individual Module Shall Not Be More Than 1200Mm Length. Additional Height Shall Be Achieved By Mounting Modules Over Them. The Bottom Module Shall Be Mounted Over A Skirting Of 85-150Mm Height. The Skirting Shall Be Designed So That Switches Can Be Provided On The Skirting Level. All The Modules Shall Be Of The Same Height. The Frames Shall Also Have Prefabricated Slots For Fixing Brackets Used To Support Worktops. Overhead Hampers, Gable Ends. Etc. The Skirting Shall Be Snap Fitted On Both Sides With Skirting Plates Made Of 0.8Mm Thick Crca Steel. Wherever Switches Are Provided On The Skirting Place Shall Have The Necessary Slots. Switches At The Skirting Level Shall Be Mounted On The Skirting. Post-The Frames Shall Be Connected At The Junctions By Aluminum Connectors. The Post Shall Be Made Of Aluminum Extrusions Of Minimum 1.2M Thickness. Trims-The Exposed Vertical And Horizontal Faces Of The Frames Shall Be Snap Fitted With Curve Trims. The Trims Shall Be Made Of Aluminum Extrusions Of Minimum 1.2Mm Thickness And 60-70Mm Width. Wire Management -Partitions System Shall Have Concealed Wire Management Capabilities To Meet Requirement And Technical Specifications And Shall Be Officered For Responsive And File Safe Operations Of Power, Telecommunications And Date (Lan) And Shall Have:-I. Separate Components For Electrical, Data And Telephone Cables Having Adequate Capability Of Both The Vertical And Horizontal Wire Movements. Ii. Slots Shall Be Provided On Tiles To Fix All Electrical And Data Points. , Iii. Storage For Excess Wires In The Partitions Iv. Easy Access For Further Maintenance And Capacity Of Additional Power, Data Phone Point To The Panels Without The Need To Dismantle Work Surface And Or Partition/ Panel. Tile Finish -1St And Second Module Laminate Tiles. 3Rd And 4Th Module Glass And 5Th Module Fabric For Front Partition. 1St And Second Module Laminate, 3Rd, 4Th And 5Th Module Fabric For Side Partition. One Pin Up And One Marker Considered For Each Cabin. Laminated Tiles -The Laminated Tiles Shall Be Made Of 9.5Mm Plpb With 1Mm Lamination On Both Sides Of The Tile. Fabric Tiles -The Fabric Tiles Shall Be Made Min 9Mm Soft Board Inside & Covered With Fabric Pasted On Them By Pva Glue. It Should Be Possible To Replace The Fabric By Peeling It Off. Pin Up Tiles: The Pin Up Tiles Shall Be Made Of 0.6Mm Metal Sheet With Fabric Pasted On Them On Pva Glue. It Should Be Possible To Replace The Fabric By Peeling It Off. Note: The Partition Should Be Adequately Fixed To The Ceiling/Wall As Approved By Officer In Charge. (For The Purpose Of Measurement And Payment Only Finished Front Area Of Partition Shall Be Measured .I.E. Length X Breadth) , Extra For Providing Double Glazed Glass Panel Instead Of Laminate Panel/Fabric Panel As Measured In Item 5 A). , Extra For Providing Door Panel With Solid Glass/ Fully Glass/ Fully Solid Instead Of Laminate Panel / Fabric Panel As Mentioned In Item No. 5A. , Low Height Partitions For Officers Cabin , Low Height Partitions For Officers Cabin Providing & Fixing In Position Modular Workstation Having Partition Height From 1200 -1500Mm Having Thickness Of 54Mm +/-6Mm. Partition Panel Consists Of Framework Made Of 1.5Mm Thick Aluminum And Would Be Finished By Aluminum Alloy Extrusions Of 1.2-2.1Mm Thickness 50-58 Mm X 12- 17Mm Of Matching Height Of The Panel And A Top Runner Of Powder Coated Aluminum Extrusions 54Mm +/6Mm X 12- 13Mm X 1.2 To 2.1Mm Thick. Further The Frame Work Should Consist Of An Infill Structure Of Batten Of Size 40-50X25-40Mm Particle Board Honey Comb Inside. The Outer Layers Shall Be Made Of Mdf/Ppb Of 3- 4Mm Thickness And Finished With Decorative Laminated Sheets Of 0.6 -1.0Mm Thickness Having One Side Bearing The Decorative Surface For Bottom Panel & Fabric For Top Panel. The Total Block Thus Would Be Of 44-54Mm Thickness. This Shall Be Attached To Top Panel By Means Of Self Tapping Screws. All Steel Parts Shall Be Pretreated For Seven Stages Anti Corrosion Treatment Followed By Epoxy Powder Coating. Height Of Skirting Shall Be 85 To 150Mm. One Intermediate Raceway To Be Provided Below Or Above The Worktop As Decided By The Officer-In-Charge. Partition To Be Supported By Stability Brackets Wherever Required. (For The Purpose Of Measurement And Payment Only Finished Front Area Of Partition Shall Be Measured .I.E. Length X Breadth). , Section B (Table) , Table For Court Rooms/ Section (Option 1) , Table For Court Rooms/ Section (Option 1):- Premium Executive Suite: The Premium Executive Suite Should Contain Executive Table Consisting Of Primary Work Surface Size : 1800 W * 900 D * 750 H; Integrated Pedestal Size 472 W * 750 H. Main Table Shall Be Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Soft Closing Access Flap With In-Build Power Box Are Provided On Work Surface For Wire Management And Secondary Work Surface And Modesty Panelshall Be Made Up Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. Under Structure Should Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping.. Integrated Pedestal Should Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Drawer Fronts Made Of 25Mm Thick Mdf One Side Pre Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Pedstal Construction Is Box-Box-File Type Which Uses Powder Coated 400 Mm Long Metal Panel Drawer Slides. Drawer Extension Is 325 Mm. Drawers Have A Soft Closing & Anti Slam Mechanism. Handles Are Provided For Ease Of Opening. Pedestal Is Provided With Lock For Security. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004, The Manufacturer Must Have Iso 18001 - The Occupational Health And Safety Management Systems, The Manufacturer Must Have Iso 50001- Energy Management Systems. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification , Green Guard For Low Chemical Emmison Of International Repute & Member Of Bifma. Supplying And Placing In Position Joining Table Of The Following Specifications. , Side Unit: The Joining Table Rhs Shall Be Of Size 1050 Width Mm X 1200 Depth Mm X 750 Height Mm.The Top Panel Shall Be 25 Mm Thick With Mfc (Melamine Faced Chipboard).The Leg Of The Joining Table Shall Be Of Metal.Polyurethane Coated Joining Table. Supplying And Placing In Position Mobile Pedestal Of The Following Specifications. The Mobile Pedestal Size Shall Be 400 Width Mm X 560 Depth Mm X 560 Height Mm.The Top Panel Shall Be 25 Mm Thick Mfc ( Melamine Faced Chipboard) Plus All The Other Panels Shall Be 18 Mm Thick Coated With Mfc (Melamine Faced Chipboard). In Mobile Pedestal All Other Panels Shall Be Of 18 Mm Thick Mfc (Melamine Faced Chipboard).In Mobile Pedestal Lock And Castors Shall Be Provided. The Handle Shall Be Of Metal. , Back Unit : Providing & Fixing Back Unit Having Overall Size (3000X490x750) And Top Made Of 36Mm Thick Board Pressed With 0.4Mm Thick Membrane Foil And Pressed With Pu Glue. The Foil Shall Be Pre-Coated With A Layer Of Polyurethane For Better Scratch Resistance. Storage Unit Of Size 2550 X 500 X 714 Shall Have Understructure Having Verticals Made Of 18Mm Thick Prelaminated Particle With 2 Open Able Shutter Storage And Drawer Fascia In Membrane Finish And Glass. , Table For Court Rooms/ Section (Option 2) , The Premium Executive Suite Should Contain Executive Table With Eru And Pedestal Consisting Of Primary Work Surface Size : 2100X2250x750; Main Table And Secondary Work Surface Made Up Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Soft Closing Access Flap With In-Build Power Box Are Provided On Work Surface For Wire Management. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. Modesty Panel Should Bemade Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. Under Structure Should Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade. Integrated Pedestal Should Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Drawer Fronts Made Of 25Mm Thick Mdf One Side Pre Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Pedstal Construction Is Box-Box-File Type Which Uses Powder Coated 400 Mm Long Metal Panel Drawer Slides. Drawer Extension Is 325 Mm. Drawers Have A Soft Closing & Anti Slam Mechanism. Handles Are Provided For Ease Of Opening. Pedestal Is Provided With Lock For Security. , Side Unit: Providing & Fixing Side Unit Having Overall Size (1200 X550x714)X 750Mm Made Of 35Mm Thick Board Pressed With 0.4Mm Thick Membrane Foil Clad Pressed With Pu Glue. The Foil Shall Be Pre-Coated With A Layer Of Polyurethane For Better Scratch Resistance. Table Shall Have Understructure Made Of 18Mm Thick Prelaminated Particleboard Having Decorative Laminate On Both Sides. The Side Unit Shall Have Open Able Shutter Storage & 3 Drawer Unit, With Facia In Membrane Finish. , Back Unit : Providing & Fixing Back Unit Having Overall Size (2400X550x1200mm (Ht) (750+450) With Top Made Of 36Mm Thick Board Pressed With 0.4Mm Thick Membrane Foil Clad Pressed With Pu Glue. The Foil Shall Be Pre-Coated With A Layer Of Polyurethane For Better Scratch Resistance. Storage Shall Have Understructure Having Verticals Made Of 18Mm Thick Prelaminated Particle. The Storage Of Size 2450 X 550 X750 + 450 (H) Shall Have Two Openable Shutter Storages And Lateral Filing Drawer Unit. The Top Shall Have Provision Of Placing Files Vertically In A Slanting Position With Extended Top By 650Mm To Cover The Corner. , Table For Court Rooms/ Section , Table For Providing & Fixing Table Having An Overall Size Of (2000X1000x750) With Top Made Of 36Mm Thick Post Formed Particle Board And Former Module Made Of 36Mm Thick Board Pressed With 0.4Mm Thick Membrane Foil Clad Pressed With Pu Glue. The Foil Shall Be Precoated With A Layer Of Polyurethane For Better Scratch Resistance. The Table Understructure Shall Have Vertical Leg Made Of 25Mm Thick Post Formed Particle Board On One Side And Supported By Three Drawer Unit Made Of 18Mm Thick Plpb With 50(D) Studs Made Of Steel Duly Powder Coated And Modesty Made Of 18Mm Thick Prelaminated Particle Board Having Decorative Laminate On Both Sides. , Side Table: Providing & Fixing Side Table Having An Overall Size Of (1200 X 500 X 714) 600Mm Without Top And 1200Mm With Top Having Top Made Of 36Mm Thick Post Formed Particle Board. , Back Unit: Providing & Fixing Back Storage Unit Having An Overall Size Of 1800+500X500x750+450 (Ht) Having Top Made Of 36Mm Thick Post Formed Particle Board. The Understructure Shall Be Made Of 18Mm Thick Prelaminated Particle Board. The Unit Shall Have Two Storages With Open Able Shutter. The Top Shall Have Provision Of Placing Files Vertically In A Slant Position With Extended Top By 500Mm To Cover The Corner. , Wooden Table , A.Wooden Table Of Size 4 X 2.5X2.5 Having Three Drawers On R.H.S. Made Of Sheesham Wood, Sunmica Top, Complete In All Respect With Polish(Melamine) , B. Wooden Table Of Size 4 X 6 X 2.5 Having Three Drawers On R.H.S. Made Of Teakwood, Teakwood Top, Complete In All Respect With Polish(Melamine) , Executive Table , Providing And Fixing In Position Executive Table Having 36Mm Thick Post Formed Top Of Particle Board Flat Pressed Three Layered Medium Density Grade-Ii Confirming To Is: 3087 Having Necessary Provision For Wire Management Data/ Computer/ Telephone Cabling A 18Mm Thick Modesty Panel Of Prelaminatd Particle Board Three Layered Medium Density Grade-Ii Type-Ii Confirming To Is: 12823 Complete As Per Salient Technical Features, Specifications, Drawings And Directions Of The Officer-In-Charge. The Vertical Shall Be Made Of 25Mm Particle Board In Post Formed Finish. , A) 2100X1050x750 Mm , B) 1800X900x750 Mm , Standard Table , A) Table For Administrative Officer / Section Officer / Section In-Charge:- Worksurface Of Size 1500 X 750 X 728 Mm To Be Made Of 18Mm Thk. Pre Laminated Particle Board (Plb) All Work Surface Edges To Be Duly Sealed With 2Mm Thick Pvc Edge Banding Understructure - Modesty Panel To Be Made Of 18Mm Thk. Pre Laminated Particle Board (Plb) All Work Surface Edges To Be Duly Sealed With 2Mm Thick Pvc Edge Banding Rectangular Frame To Be Made Of Fabricated Component In 1.2Mm Thick Crca (Is:513), Finish: Powder Coat (Epoxy Polyester) Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. Legs To Be Made Of Fabricated Component In 38Mmx25mmx1.2Mm Thick Ms Erw Tube (Is:7138), Finish: Powder Coat (Epoxy Polyester) Plastic Cap For Cable To Be Injection Moulded Polypropylene. Leveler Glide For Leg To Be Nylon 6 & Ms Bolt Storage/Pedestal - Shell To Be Made Of 0.6Mm Thick Crca (Is:513) , Finish: Powder Coat (Epoxy Polyester). Drawer Tray To Be Made Of 0.6Mm Thick Crca (Is:513), Finish: Powder Coat (Epoxy Polyester). Drawer Front To Be Made Of 0.8Mm Thick Crca (Is:513), Finish: Powder Coat (Epoxy Polyester). Frame Assembly To Be Made Of 1.2Mm Thick Crca (Is:513), Finish: Powder Coat Epoxy Along With Key Board (Dimensions - 645 X 225 Mm Weight - 3.75 Kg Material - Crca) And Cpu Trolley ( Dimensions - * Adjustable Width (150 - 225 Mm)Weight - 1.5 Kg Material - Crca Steel Finish : Powder Coating Thickness -0.8 Mm )Overall Size Of Table Is 1500X750x750 Mm. , B) The Table Is Of Size 1350X600x750mm .The Top Of Table Is To Be Made Of 18 Mm Thick Pre-Laminated Plain Particle Board. All The Edges Of The Top Are Duly Sealed Using 2 Mm Thick Doelleken Beading, Fixed By Using Jowart/ Klibert Glue. Understructure Is Made In Form Of ‘C’ Frame. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. Made Of Crca Ms Sheet Of 1.2 Mm Thk. The Tubular Frame Is To Be Made Of Ms Erw Round Tubes Dia 25.4 Mm X 1.2 Mm Thk. Drawer Unit (Single Drawer) : The Shell Of The Drawer Unit Is To Be Made Of 0.8 Mm Thick Crca Ms Sheet. The Drawer Tray Is Made Of 0.6 Mm Thick Crca Sheet And The Drawer Front Is Made Of 0.8 Mm Thick Crca Sheet. Drawer Slides Are Based On Friction Slides Of 1.2 Mm Thick Crca Sheet. It Should Have 6 Lever Brass Lock. The Handles Of Drawer Are Made Of Abs Plastic. , C) Standard Table For Staff & Printer:- The Table Is Of Size 1200X600x750 Mm The Top Of Table Is To Be Made Of 18 Mm Thick Pre-Laminated Plain Particle Board. All The Edges Of The Top Are Duly Sealed Using 2 Mm Thick Doelleken Beading, Fixed By Using Jowart/ Klibert Glue. Understructure Is Made In Form Of ‘C’ Frame. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms), Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. Made Of Crca Ms Sheet Of 1.2 Mm Thk. The Tubular Frame Is To Be Made Of Ms Erw Round Tubes Dia 25.4 Mm X 1.2 Mm Thk. Drawer Unit (Single Drawer) : The Shell Of The Drawer Unit Is To Be Made Of 0.8 Mm Thick Crca Ms Sheet. The Drawer Tray Is Made Of 0.6 Mm Thick Crca Sheet And The Drawer Front Is Made Of 0.8 Mm Thick Crca Sheet. Drawer Slides Are Based On Friction Slides Of 1.2 Mm Thick Crca Sheet. It Should Have 6 Lever Brass Lock. The Handles Of Drawer Are Made Of Abs Plastic. , The Conference Table To Be Modular In Nature. The Items To Be Supplied As Per The Drawing Attached. It Should Have Flexibility To Join Individual Table To Form Any Size Of Conference Table. The Basic Tabletop Should Be Made Of 25 Mm Thick Plb, With 2 Mm Thk. Pvc Lipping Of The Same Colour. Side Panels To Be Made Of 18 Mm Thick Plb With 2 Mm Thick Pvc Lipping Of Matching Colour. The Modesty Panel Is To Be In Two Pieces And In Two Colours. The Big Upper (300 Mm) Modesty Is In Black Colour And The Small (150 Mm) Modesty Is In The Colour Of The Tabletop. Wire Carriers Is To Be Made Of 0.80 Mm Thick Ms – Crca – ‘D” Grade Sheet, In Black Powder Coating. Ms Stiffeners Are To Be Provided As And Where Required. The Wire Carrier Dimensions For 1 Seater Should Be 647 Mm X 100 Mm X 100Mm. The Wire Carrier Dimensions For 2 Seater Should Be 1322 Mm X 100 Mm X 100Mm. , Two Seater Unit:W - 1350 Mm X D - 600 Mm X H- 738 Mm , Single Seater Unit: W - 675 Mm X D - 600 Mm X H- 738 Mm , Providing And Fixing Of Dining Table Having 25Mm Thick Post Formed Particle Board Flat Pressed Three Layered Medium Density Grade-Ii Confirming To Is : 3087 Top Having 0.70Mm Thick Decorative Laminate On Top And 0.60Mm Thick Balancing On Underside With Front Edges Profiled And Exposed Sides Sealed With Pvc Edge Banding Tape, Understructure Shall Be In 18Mm Prelaminated Particle Board. , 600X600x750mm , 1500X750x750 Mm , 2100X750x750 Mm , Providing And Fixing Of Dining Table Having 25Mm Thick Post Formed Particle Board Flat Pressed Three Layered Medium Density Grade-Ii Confirming To Is : 3087 Top Having 0.70Mm Thick Decorative Laminate On Top And 0.60Mm Thick Balancing On Underside With Front Edges Profiled And Exposed Sides Sealed With Pvc Edge Banding Tape, Understructure Steel Duly Powder Coated. , 600X600x750mm , 1500X750x750 Mm , 2100X750x750 Mm , Section C (Drawer & Storage) , Made Up Of Crca Steel Duly Powder Coated Of Thickness 22 Swg. A Welded Assembly Is Fitted At The Bottom To Fix This Pedestal With Worktop. Pedestal Is Fixed To Worktop With Screws Through Top Stiffeners Of The Pedestal And With A Bracket Fixed To The Panel. Pedestal Leg Assembly Is Fabricated By Co2 Welding Vertaical Ms Tubesection Of Size 38 X 25Mm X 16 Bg (Is: 7138 Erw Tube) Inside Which Leveller Holder Plates Of Size 34 X 21 X 5 Mm ( Is: 2062, 5 Mm Hr) Are Welded With Horizontal Bottom Channel Made Of 2 Mm Thick Ms Crca, Grade D As Per (Is513) Pedestal Height Is 600 Mm Without Leg Assembly And 720 Mm With Leg Assembly Up To Bottom Of Worktop. Overall Size Is : , 646 H X 390 W X 585 D , 450X550x725 , Overhead , Providing & Fixing Overhead Storage Units Wall/Partition Hung Made Up Of 18Mm Prelaminated Particle Board Having Two Open Able Shutters With All Exposed Edges Sealed With 2Mm Pvc Edge Banding Tape & With Proper Locking Arrangement. The Depth Of The Overhead Shall Be 350Mm With Height As 400Mm. , Providing & Fixing Of Storage Unit Of 750Mm -1200Mm Height X 450Mm Depth Having Top Made Of 25Mm Thick Post Formed Particle Board Flat Pressed Three Layered Medium Density Grade-Ii Confirming To Is : 3087 And Understructure Made Of 18Mm Thick Prelaminated Particle Board Three Layered Medium Density Grade-Ii Type -Ii Confirming To Is : 12823 Having Two Open Able Shutters. All Exposed Edges Of Plpb Shall Be Sealed With Pvc Edge Banding Tape. The Unit Shall Have Proper Locking Arrangement With Duplicate Keys. , Body :- Body Is Made From 18Mm Plb With All The Edges Sealed With 0.8 Mmthick Pvc Edgeband. The Back Panel Is 9Mm White Plt. The Entire Construction Is Ready To Assemble Unit And Is Assembled With Suitable Kd Fittings. The Shelves And Separator Panels ( If Available ) Is Made From 18 Mm White Plt And Edges Are Sealed With 0.8 Mm Edge Band. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. The Bottom Shelf Is Fixed And Other Shelves Have One Step Adjustment For Optimizing The Space. Doors :Door Panels Ae Made From 18 Mm Plb With 2 Mm Edge Band On Alledges Ad A Flush Plastic Handle Is Fitted Vertically At The Center Of The Door. The Hinge Door Has Suitable Hinges And Hdu Is Fitted With An Adjustable Fitting For Height Adjustment. All The Storages Are Fitted With A 6 Mm Leveler At Bottom For Leveling. Overall Size Of Storage Unit 1604 X 396 X 1230. , Section D (Misc) , Providing And Fixing Post Formed Key Board Trays Of Eepcco/ Ozone Or Equivalent, Size 600X350 Mm Made Out Of 25 Mm Thick Particle Board With Post Formed Decorative Laminate On Top And Having Balancing Lamination On The Unexposed Face In Work Stations, Executive Table Or Side Units In Approved Color And Texture As Per Salient Technical Features, Specifications And Drawings As Approved By Officer-In-Charge. , Providing And Fixing Cpu Trolley Made Of Size 220X250x250 Mm Having Adjustable Width And Lockable Castors At Base, Made Of 0.9 Mm Thick Complete As Per Salient Technical Features, Specifications And Drawings As Approved By Officer-In- Charge. , Podium , Providing & Fixing Podium Having Overall Size (750Wx600dx1250h), Top Made Up Of 25Mm Thick Particle Board Having Post Formed On Top & Vertical Decorative Laminate On Top, Modesty Made Up Of 18 Mm Thick Prelaminated Particle Board Having And Balancing Laminate On Unexposed Face, Having All Exposed Edges Sealed With 2Mm Pvc Edge Banding Tape. , Providing And Placing Of Chairs , Chair For Court Room Section :- Executive High Back Chair Ofthe Chair Should Be Tested Onbifma Standards With Seat Slide For All Division Incharge With High Back Size: 51.6 Cm. (W) X 75.2 Cm. (H)- Seat/Back Assembly To Be Made Up Of 1.2 ± 0.1Cm Thk. Hot Pressed Plywood Upholstered With Knitted Fabric ,Over Moulded High Resilience Polyurethane Foam. Seat Size Should Be49.0 Cm. (W) X 51.4 Cm. (D). Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. The Hr Polyurethane Foam Should Moulded With Density = 55+/-2 Kg/M³ And Hardness 16 ± 2 Kgf As Per Is:7888 For 25% Compression. The Adjustable Armrest Shall Have Following Features :· - Up-Down Adjustment– 8 Steps (8.0±0.5 Cm Range Height Adjustable Armrest Structure Which Is Powder Coated & Fitted With An Armrest Top. - Fixed Armrest Top Is Pu Molded Over Metal Insert.Chair Should Have Front Pivot Synchro Mechanism With Following Features360° Revolving Type. · Single Point Control.Front-Pivot For Tilt With Feet Resting On Ground Ensuring More Comfort. · Tilt Tension Adjustment. · 4-Position Locking With Anti-Shock Feature. · Seat/Back Tilting Ratio Of 1:2. Chair Back Can Be Adjusted In 5 Positions Manually. Stroke Of Height Adjustable Spines Hall Be 7 Cm. Chair Should Have Pedestal Assembly With Castors Which Shall Be Injection Moulded In Black 30% Glass-Filled Nylon And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Pitch-Center Dia Is Ø66.1 ± 0.5 Cm. (76.1 ± 1.0 Cm. With Castors).Seat Can Be Slide Horizontally As Per User Convenience. Stroke Of Seat Slide Shall Be 4 Cm- 5 Cm. , Chair For Court Rooms/ Sections Visitor , Chair For Court Rooms/ Sections Visitor :- Executive Visitors Chair Of, The Chair Should Betested On Bifma Standards Without Slide For All Division Incharge With Width (W) : 57.5 Cm;Depth (D) : 58.2 Cm; Height (H) : 100.8 Cm . Seat Height (Sh) : 47.0 Cm With Hot Pressed Plywood Upholstered With Knitted Fabric ,Over Moulded High Resilience Polyurethane Foam. Seat Size Should Be49.0 Cm. (W) X 51.4 Cm. (D). Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. The Hr Polyurethane Foam Should Moulded With Density = 55+/-2 Kg/M³ And Hardness 16 ± 2 Kgf As Per Is:7888 For 25% Compression. Visitor Chair Should Have Tubular Visitor Framewhich Shall Bepowder Coated ( Dft 40-60 Microns ) Cantilever Structure & Made Of Dia.Ø 2.54 ±0.03Cm. X 0.2 ±0.016Cm.Thk. M.S. E.R.W Tube With A Connecting M.S. Spine Welded To It. Back Spine Shall Be Fitted To The Frame Assembly.· Fixed Armrest Top Shall Be Pu Molded Over Metal Insert. , Chair For Court Rooms/ Section, Head Conference Chair , Chair For Court Rooms/ Section, Head Conference Chair :-The Seat And Back Are To Be Made Of 1.2 Cm Thick Hot Pressed Plywood Upholstered With Fabric Covers And Molded Polyurethane Foam Of Density 45 +/- 2 Kg/M3and Hardness = 20 +/- 2 On Hampden Machine At 255 Compression. The Back Foam Is To Be Designed With Contoured Lumber Support For Extra Comfort. The Seat Should Have Extra Foam At Front Edge To Give Comfort To Popliteal Area. Back Size : 47.5 Cm W X 69.5 Cm H, Seat Size 47.0 Cm W X 48.0 Cm D. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms), Iso 14001:2004. Green Guard Also Included. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. The One Piece Armrest Are To Be Injection Molded From Black Co-Polymerpolypropylene. Chair Should Have 360 Deg Swivel Mechanism With, With Upright Locking, Tilt Tension Adjustment And Seat Back Tiling Ration Of 1:3 (6 Degree Seat Tilt / 18 Degree Back Tilt). Chair Should Have Five Prong Pedestals (To Be Injection Molded In Black 30% Glass Filled Nylon) And Fitted With Twin Castors And Pneumatic Height Adjustment (Stroke – 125 Mm). Pedestal Pitch Centre Dia, Without Castors Is To Be 68 Cms. Overall Size : D-76 Cm. X W- 76 Cm. Xh-98.5 To 110.5 Cm., Seat Height 42.5 Cm To 54.5 Cm , Chair For Administrative Officer / Section Officer / Section In-Charge & Conference Chair , Chair For Administrative Officer / Section Officer / Section In-Charge & Conference Chair:- The Seat And Back Are To Be Made Of 1.2 Cm Thick Hot Pressed Plywood Upholstered With Fabric Covers And Molded Polyurethane Foam Of Density 45 +/- 2 Kg/M3and Hardness = 20 +/- 2 On Hampden Machine At 255 Compression. The Back Foam Is To Be Designed With Contoured Lumber Support For Extra Comfort. The Seat Should Have Extra Foam At Front Edge To Give Comfort To Popliteal Area. Back Size : 47.5 Cm W X 58.5 Cm H, Seat Size 47.0 Cm W X 48.0 Cm D. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. The One Piece Armrest Are To Be Injection Molded From Black Co-Polymerpolypropylene. Chair Should Have 360 Deg Swivel Mechanism With, With Upright Locking, Tilt Tension Adjustment And Seat Back Tiling Ration Of 1:3 (6 Degree Seat Tilt / 18 Degree Back Tilt). Chair Should Have Five Prong Pedestal (To Be Injection Molded In Black 30% Glass Filled Nylon) And Fitted With Twin Castors And Pneumatic Height Adjustment (Stroke – 125 Mm). Pedestal Pitch Centre Dia, Without Castors Is To Be 68 Cms. Overall Size : D-76 Cm. X W- 76 Cm. Xh-98.5 To 110.5 Cm., Seat Height 42.5 Cm To 54.5 Cm , Visitor Chair , Visitor Chair:- The Seat And Back Are To Be Made Of 1.2 Cm Thick Hot Pressed Plywood Upholstered With Fabric Covers And Molded Polyurethane Foam Of Density 45 +/- 2 Kg/M3and Hardness = 20 +/- 2 On Hampden Machine At 255 Compression. The Back Foam Is To Be Designed With Contoured Lumber Support For Extra Comfort. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. The Seat Should Have Extra Foam At Front Edge To Give Comfort To Popliteal Area. Back Size : 47.5 Cm W X 58.0 Cm H, Seat Size 47.0 Cm W X 48.0 Cm D. The One Piece Armrest Are To Be Injection Molded From Black Co-Polymerpolypropylene. Tubular Frame Should Be Powder Coated And Is Cantilevered Type, Made From Dia 25.4 Mm X 2 Mm Thk. Ms Erw Tube. Overall Size : D-64 Cm. X W- 61 Cm. Xh-89.5, Seat Height 46.5 Cm , High Back Executive Chair (Type-A) , High Back Executive Chair (Type-A) :- The Seat And Back Are To Be Made Of 1.2 Cm Thick Hot Pressed Plywood Upholstered With Fabric And Foam Of Density 45 +/- 2 Kg/M3 With Pvc Lipping All Around. Back Size : 49.5 Cm W X 69.50 Cm H, Seat Size 49.5 Cm W X 44.0 Cm D. The One Piece Armrest Has To Be Made Of Black Integral Skin Polyurethane With 50-70 Shore Hardness And Reinforced With M.S. Insert. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms), Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. The Armrests Are To Be Scratch And Weather Resistant. The Armrests Are Fitted To The Seat With Seat Armrest Connecting Bracket Made Of 0.3 Cm. Thk. Chair Should Have 360 Deg Swivel Mechanism With Pivot At Center, With Upright Locking. Chair Should Have Five Prong Pedestal With 5 Nos. Of Twin Castors , Injection Moulded In 30% Glass Filled Black Nylon And Pneumatic Height Adjustment. Overall Size : D-76 Cm. X W- 76 Cm. Xh- 77.5 Cms. To 87.5 Cms., Seat Height 42.5 Cm To 52.5 Cm. , Executive Visitor Chair (Type-B) , Executive Visitor Chair (Type-B) :- The Seat And Back Are To Be Made Of 1.2 Cm Thick Hot Pressed Plywood Upholstered With Fabric And Foam Of Density 45 +/- 2 Kg/M3 With Pvc Lipping All Around. Back Size : 49.5 Cm W X 47.0 Cm H, Seat Size 49.5 Cm W X 44.0 Cm D. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms), Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. The One Piece Armrest Has To Be Made Of Black Integral Skin Polyurethane With 50-70 Shore Hardness And Reinforced With M.S. Insert. The Armrests Are To Be Scratch And Weather Resistant. The Armrests Are Fitted To The Seat With Seat Armrest Connecting Bracket Made Of 0.3 Cm. Thk. Overall Size : D-58 Cm. X W- 55 Cm. Xh- 84 Cms., Seat Height 45 Cm. , Staff & Supervisor Chair , Staff & Supervisor Chair :- Mid Back Revolving Chair Having Seat/Back Assembly: The Seat And Back Are Made Up Of 1.2 Cm. Thick Hot-Pressed Plywood, Upholstered With Changeable Fabric Upholstery Covers And Moulded Polyurethane Foam, Together With Seat And Back Cover. The Back Foam Is Designed With Contoured Lumbar Support For Extra Comfort. Back Size: 39.0Cm. (W) X 47.0Cm. (H), Seat Size: 45.0Cm. (W) X 52.0Cm. (D). Polyurethane Foam: The Polyurethane Foam Is Moulded With Density = 45 +/-2 Kg/M3 And Hardness = 20 +/- 2 On Hampden Machine At 25% Compression. Armrests: The Armrests Are Made Of Black Integral Skin Polyurethane With 50-70 Shore ‘A’ Hardness And Reinforced With M.S. Insert. The P.U.Armrests Are Then Fixed To Black Powder Coated Armrest Brackets Made Of 0.5Cm.Thk. Hr Steel Fitted With Claddings Made Of Injection Moulded Polypropylene. Approx. Size Of The Armrest Is 21.0Cm. (L) X 6.4(W). Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. Permanent Contact Mechanism:The Permanent Contact Mechanism Is Designed With The Following Features: 360° Revolving Type. 14° Maximum Back-Tilt Only. Upright Position Locking. Tilt Tension Adjustment. Spine Cover: The Spine Cover Is Injection Moulded In Black Co-Polymer Polypropylene. Pneumatic Height Adjustment:The Pneumatic Height Adjustment Has An Adjustment Stroke Of 12.0 Cm.Telescopic Bellow Assembly:The Bellow Is 3 Piece Telescopic Type And Injection Moulded In Black Polypropylene. Pedestal Assembly : The Pedestal Is Fabricated From 0.2Cm. Thick Cr Steel, Powder Coated And Fitted With An Injection Moulded Black Polypropylene Hub Cap And 5 Nos. Twin Wheel Castors.(Castor Wheel Dia. 5.0Cm.) The Pedestal Is 60.0Cm. Pitch-Centre Dia. (70.0 Cm With Castors). Twin Wheel Castors: The Twin Wheel Castors Are Injection Moulded In Black Nylon. , Workstation Chair , Workstation Chair:- Seat/ Back: The Seat Is Made Of 1.2 Cm Thick Hot Pressed Plywood. Upholstered With Fabricand Moulded Polyurethane Foam. The Back Is A Fabricated Frame Assembly, Powder Coated And Upholstered With A Net Mesh Type . The Back Is Frp Frame. Seat Size: W-47 Cms X D-47 Cms.Backsize: W- 44 Cms. X H – 49 Cms. Polyurethane Foam: Moulded With Density 45 +/- 2 Kg/M3 And Hardness 20 +/- 2 Kg. On Hampden Machine At 25% Compression. Armrests: The Armrest Is Injection Moulded In Black Polypropylene, In Single Piece. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. Pneumatic Height Adjustment: The Pneumatic Height Adjustment Should Be Maintenance Free And Should Have Adjustment Stroke Of 10.0 Cms. Pedestal Assembly: The Pedestal Is To Be Made From Polypropylene Mould And Fitted With 5 Nos. Twin Wheel Castors (Castor Wheel Dia. Of 5.0 Cms). The Pedestal Is 55.0 Cms. Pith Centre Dia. Twin Wheel Castors: They Should Be Injection Moulded In 30% Glass Filled Black Nylon. , Providing & Placing Of Multi Seater Chairs , Providing & Placing Of Multi Seater Chairs :- Three Seater Metal Perforated Chair, With Two Arms Without Cushion To Be Made Of The Following Components: Cross Beam: To Be Made Of Black Powder Coated Rectangular Ms Erw Tube Size Of 8+/-0.03 Cm. X 4 +/- 0.03 Cm. X 0.2 +/.-0.016 Cm. Leg & Armrest: This Is To Be Chrome Plated And Made Of Cold Rolled Steel With 0.12 +/- 0.013 Cm. Thicknesses Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. Seat / Back Shell: This Is To Be Made Of 1.6 Mm Thick Powder Coated Perforated Shell Made From Cold Rolled Ms Sheet 0.16 +/- 0.013 Cm Thickness. The Side Bar Is Made From Chrome Plated Solid Steel 3 +/- 0.03 Cm X 1.2 +/- 0.03 Cm (Din174) With Fluting And Plastic Inserts. The Shell Is To Be Assembled On The Cross Beam With The Help Of M8 Bolts (N Per Seat- 8 Nos. – Seat To Bracket And 4 Nos. Bracket To Cross Beam) Over All Dimensions: W – 160 Cm. X D–56 Cm. X H–70 Cm. X Sh – 41 Cm , Sofa For Waiting , Sofa For Waiting :- It Should Be Made Of Pine Wood And 12 Mm Plywood (Is-303, Commercial Plywood) Frame, Upholstered With Pvc Upholstery (0.9 Mm Thickness, Weight – Gsm - 575) In Black Color. The Slab Stock Foam Used Has To Be Soft For Comfort Seating. Seat Foam Thickness To Be 69, 22, 10 Mm With Density Of 26 Kg/M3. Back Foam Thickness To Be 45 Mm With Density Of 28 Kg/M3. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms), Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. Armrest Foam Thickness To Be 45 Mm With Density Of 26 Kg/M3.Belt / Webbing Material To Be 68 Mm And 48 Mm Wide. Plastic Legs To Be Fitted Along With Pvc Bushes. , A) Single Seater:- One Seater Overall Size: 92.0 Cm (W)X87.0 Cm (D) X73.0 Cm (H) X 39.5 Cm (Sh). (+ / - 2.5 Cm Variation Permitted) , B) Two Seater:- Two Seater Overall Size: 133.0 Cm (W)X87.0 Cm (D) X73.0 Cm (H) X 39.5 Cm (Sh). , C) Three Seater :- Three Seater Overall Size: 175.0 Cm (W)X 87.0 Cm (D) X73.0 Cm (H) X 39.5.0 Cm (Sh) . (+ / - 2.5 Cm Variation Permitted) , Chair Multi Purpose:The Seat And Back Should Be Made Of Injection Molded High Inpact Strength Polypropylene Polymer Compound With Indoor Grade Uv Resistance. Seat Size :52.5 Cm (W) X 53.2 Cm (D). Back Size: 51.6 Cm (W) X 0.5 Cm (H). S.S. Understructure : The Tubular Welded Frame Is Made From Dia 2.22 +/- 0.03 Cm X 0.12 +/- 0.0128 Cm And 3.5 +/- 0.03 Cm X 1.5 +/- 0.03 Cm X 0.12 +/- 0.0128 Cm Stainless Steel 202 Grade Tube. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms), Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. The Tubes Are Buff Polished To Give Shiny Finish. Shoe: The Shoes Are Made Of High Impact Strength Ploy Propylene Polymer Compound With Indoor Grade Uv Resistance And Pressed Fitted With Tubular Frame And Ss Understructure. , Executive Table , Executive Table :- The Main Table Is Of Size 1800 (W) X 1800 (D) X 760 (H), With Top Thickness Of 36 Mm ( 18 Mm Plt + 18 Mm Plb Baton). The Top Of Main Table Is Laminated With 2 Mm Lipping All Around. Understructure Is To Be Made Of Rectangular Tube Of Size 40X20x1.6 Mm Thickness With Crms 3 Mm Thick Plates For Bolting The Leg. Modesty (Front & Side) Is To Be Made Of Perforated Ms Sheet Of 0.9 Mm Thickness. Legs Are To Be Made From Round Tube Of Dia 50 X 1.6 Mm Thickness. Leveling Screws To Be Provided. Drawer Unit Is To Be Made Of Ms Sheet Of Thickness 0.8 Mm / 0.90 Mm. Size Should Be W – 390 Mm X D – 590 Mm X H – 646 Mm. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms), Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. The Side Table Is Of Size 1200 (W) X 600 (D) X 750 (H), With Top Thickness Of 36 Mm (18 Mm Plt + 18 Mm Plb Baton). The Top Of Side Table Is Laminated With 2 Mm Lipping All Around. Understructure Is To Be Made Of Rectangular Tube Of Size 40X20x1.6 Mm Thickness With Crms 3 Mm Thick Plates For Bolting The Leg. Modesty (Front & One Side) Is To Be Made Of Perforated Ms Sheet Of 0.9 Mm Thickness. Three Legs Are To Be Made From Round Tube Of Dia 50 X 1.6 Mm Thickness. Leveling Screws To Be Provided , Executive Chair (Type-C) , The Seat Shall Be Made Up Of 1.2 Cm. Thick Hot Pressed Plywood Uphoistered With Fabric And Moulded Polyurethane Foam. The Back Shall Be Made Up 1.2Cm. Thick Hot Pressed Plywood Uphoistered With Replaceable Fabric Upholstery Covers And Moulded Polyurethane Foam. The Back Ply And Foam Shall Be Designed With Contoured Lumber Support For Comfortable Seating Posture. Back Size 48Cm.(W) X76.0Cm(H), Seat Size 51.0Cm(W) X 48.0Cm(D) Polyurethane Foam: The Polyurethane Foam For Seat And Back Shall Be Moulded With Density=45+/-2Kg/M3 And Hardness=20+/-2.Armrests (Adjustable): The Armrest Top Shall Bemade Of Moulded Polyurethane(P.U.) And Mounted On To A Drop Lift Height Adustable Type M.S. Tubular Armrest Support Chrome Plated. The Armrest Height Shall Be Adjustable U To 6.5Cm In 5 Steps & Also Has Swivel Adjustment Of 22 On Both Sides. Knee Tilt Synchro Mechanism With Seat Depth Adjustment Mechanism: The Mechanism Shall Be Designed With The Following Features:360 Revolving Type, Single Point Control, Front Pivot For Tilt With Feet Resting On Ground Ensuring More Comfort., Tilt Tension Adjustment., 4-Position Locking With Anti-Shock Feature., Seat Back Tilting Ration Of 1:2, Seat Depth Adjustment Of 6Cm Can Be Locked In 6 Positions. Adjustable Backrest: The Backrest Consists Of A Sliding Up Down Mechanism, Which Can Be Adjusted In The Range Of 7.5Cm And Can Be Locked In 4 Positions For Correct Position Of Lumber Support. Pneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Of 9.0Cm. Pedestal Assembly: The Pedestal Is Fabricated From Steel, Chrome Plated And Assembled With Injection Moulded Black Polypropylene Hub Cap And 5 Nos. Twin Wheel Castors (Castor Wheel Dia.5.0Cm). The Pedestal Is 66.0Cm. Pitch-Center Dia. (76.0Cm With Castors). Twin Wheel Castors: The Twin Wheel Castors Are Injection. Overall Dimensions Of Chair Shall Be Width-76Cm, Depth-76Cm, Height-101.5Cm-117.5Cm,Seat Height-46Cm-55Cm. , Sofa Set , A. Sofa Set 3 Seater- Sofa Set :- Three Seater Sofa For Officers Waiting Area Of Size- 2060 W X 905 D X 820 H Mm. With Seating Area Ofwidth 450Mm. The Seat Should Be Made Up Of 28 Density Pu Foam +/- 2 Kg/Cu.Mtr With An Additional Top Layer Of Super Soft Pu Foam Of 32 Density +/- 2Kg/Cu.Mtr And Uphoslted With Fabric. The Back Should Be Made Up Of 28 Density Pu Foam +/- 2 Kg/Cu.Mtr With An Additional Top Layer Of Super Soft Pu Foam Of 32 Density +/- 2Kg/Cu.Mtr And Uphoslted With Fabric. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. The Under Structure Should Be Made Of 120Mm Thick Hot Pressed Plywood (Moisture Resistance & Termite Proof As Per Is : 303) & Pinewood Of Cross Section Divide Of Major Knots & Surface Defects6 Nos. Per Seat & 3.8 Mm Dia Zigzag Spring Assembly Is Mounted Over Understructure For Cushioning Purpose. Legs Should Be Made Of Stainless Steel (Grade Ss 202) Tube & Plate With Plastic End Cap. , B. 2 Seater Sofa , B. Two Seater Sofa For Officers Waiting Area Of Size- 1460 W X 905 D X 820 H Mm. With Seating Area Ofwidth 450Mm. The Seat Should Be Made Up Of 28 Density Pu Foam +/- 2 Kg/Cu.Mtr With An Additional Top Layer Of Super Soft Pu Foam Of 32 Density +/- 2Kg/Cu.Mtr And Up Hoslted With Fabric. The Back Should Be Made Up Of 28 Density Pu Foam +/- 2 Kg/Cu.Mtr With An Additional Top Layer Of Super Soft Pu Foam Of 32 Density +/- 2Kg/Cu.Mtr And Uphoslted With Fabric. Manufacturing Bidders Should Have The Following Iso Standards –Iso – 9001:2008, And A Robust Quality Management System (Qms),Iso 14001:2004. The Manufacturer Should Be Certified For Comprehensive Green Manufacturing Certification Of Repute & Member Of Bifma. The Under Structure Should Be Made Of 120Mm Thick Hot Pressed Plywood (Moisture Resistance & Termite Proof As Per Is : 303) & Pinewood Of Cross Section Divide Of Major Knots & Surface Defects6 Nos. Per Seat & 3.8 Mm Dia Zigzag Spring Assembly Is Mounted Over Understructure For Cushioning Purpose. Legs Should Be Made Of Stainless Steel (Grade Ss 202) Tube & Plate With Plastic End Cap. , Centre Table , Size Of Centre Table Is 1100 W X 600D X 460 Ht. Glass Top- 10Mm Tampered Glass Top And 8Mm Tampered Bottom Glass For Storage Option. Chrome Plated Understructure, Passed 48 Hrs Salt Spray Test. Glass Attached To The Understructure Via. Uv Disc. , A- Workstation , All Wood Table With Eru And Pedestal Having Main Desk 1350Wx750dx750h The Table Top Shall Be In White Cedar, Side Panels Are To Be In Black, While The Modesty Panel Is To Be A Combination Of Black & White Cedar. The Eru Is To Be An Independent Standing Unit, It Shall Be Common For Lhs & Rhs.Eru Size 1200Mmw X 450Mm D X 750Mm H The Eru Top Should Be In White Cedar, Side Panels Are In Black, While The Modesty Panel Is A Combination Of Black & White Cedar. The Two Drawer (1 Ox Drawer & 1 Filing Drawer) Mobiles Pedestal Is To Be Available In Size : 390X435x529 Mm. The Top & Drawer Fronts Are In White Cedar While The Other Components Are To Be In Black. Tops To Be Made From 18Mm Thick Plb With Pvc Lipping. Side Panels To Be Made From 18Mm Thick Plt With Pvc Lipping. Modesty Panel To Be Made From 18Mm Thick Plt With Pvc Lipping. Bigger Upper Panel In Black And Smaller Lower Panel In White Cedar. Mobile Pedestal : One Box And One Filing Drawer With 18Mm Thick Plb Fronts And Top. Handles : Black Powder Coated Die Cast Aluminum Alloy Handles. , Revolving Chair (For Staff) , The Seat And Back Are To Be Made If 1.2 Mm Thick Hot Pressed Plywood Upholstered With Fabric And Foam Of Density 45+/-2Kg/M3 With Pvc Lipping All Around. Back Size : 49.5 Cm W X 45.4Cm H, Seat Size 49.5Cm W X 43.0 Cm D. One Piece Arm Rest Has To Be Made Of Black Integral Skin Polyurethane With 50-70 Shore Hardness And Reinforced With M.S. Insert. The Armrest Should Be Scratch And Weather Resistant. The Armrest Are To Be Fitted To The Seat Armrest Connecting Bracket Made Of 0.3 +/-0.022Cm Thk Hr Steel. The Pneumatic Height Adjustment Should Have Adjustment Stroke 12.0 +/-0.3 Cm. Chair Should Have 360 Deg Swivel Mechanism With Pivot At Center, With Upright Locking. Chair Should Have Five Prong Pedestal With Twin Castors Overall Size : D-76.3 Cm X W-76.3 Cm X H-78.4 To 90.4 Cms, Seat Height 43.4 Cm To 55.4 Cm. , Workstation , The Table Is Of Size 1350(W) X750(D) X 728(H). The Top Of Table Is To Be Made Of 18 Mm Thick Pre-Laminated Plain Particle Board. All The Edges Of The Top Are Duly Sealed Using 2 Mm Thick Deolleken Beading, Fixed By Using Jowart/Kliberet Glue. Understructure Is Made In Form Of C Frame. Made Of Crca Ms Sheet Of 1.2 Mm Thick. The Tubular Frame Is To Be Made Of Mserw Round Tubes Dia 25.4Mm X 1.2Mm Thick. Drawer Unit (3 Drawer). The Shell Of The Drawer Unit Is To Be Made Of 0.8Mm Thick Crca Ms Sheet. Thedrawer Tray Is Made Of 0.6Mm Thick Crca Sheet And The Drawer Front Is Made Of 0.8Mm Thick Crca Sheet. Drawer Slides Are Based On Friction Slides Of 1.2Mm Thick Crca Sheet. It Should Have 6 Lever Brass Lock. The Handles Of Drawer Are Made Of Abs Plastic. , Revolving Chair , Seat/Back Assembly- The Seat And Back Should Be Made From 1.2+/-0.1Cm Thick Hot Pressed Plywood And Upholstered With Fabric And Moulded Polyurethane Foam Together With Seat And Back Covers. Back Size-45.0Cm(W)X 53.0Cm(H) Seat Size- 52.0Cm(W)X 48.0Cm(H) Polyurethane Foam- The Hr Polyurethane Foam Should Be Moulded With Density=45+/-2Kg/M3 And Hardness Load 16+/-2 Kg As Per Is:7888 For 25% Compression. Seat/Back Covers- The Seat And Back Covers Should Be Injection Moulded In Black Co-Polymer Polypropylene Armrest Assembly- The One Piece Armrest Should Be Scratch And Weather Resistant. The Armrest Should Be Fitted To The Seat With Armrest Brackets Made Of 0.5+/-0.05Ch Thk Hr Steel. Mechanism- Mechanism Should Have Features Like 360 Degree Revolving Type, 14 Degree+/-2 Degree Maximum Back Tilt Only, Upright Position Locking. Tilt Tension Adjustment. Pnematic Height Adjustment- Prematic Height Adjustment Should Have Adjustment Stroke Of 11.0+/-0.3Cm. Pedestal Assembly- The Pedestal Should Be Fabricated From0.2+/-0.02Cm Thick Hr Steel (Is:Dd1079/Hr), Powder (Dft 40-60Microns) And Fitted With And Injection Moulded Black Polypropylene Hub Cap And 5 Nos. Twin Wheel Castors. The Pedestal Should Have 60.0+/-0.5Cm Pitch Centre Dia (70.0+/-1.0Cm With Castors) , Drawer & Storage Unit , It Should Have Multi Bend Construction With Press Fit Fasteners Free Design, It Should Have Roll Formed Side, Back And Sides Of Drawers, It Should Have 10 Lever Cam Lock. All The Drawers Should Be Mounted On Nickel Chrome Plated Ball Slides. It Should Have Anti Tilt Mechanism And Anti Rebound Mechanism. All Steel Components Should Undergo Eight Tank Anti Rust Treatment And Or Baked Epoxy Polyester Powder Coated With 50-60 Dry Film Thickness. The Crca Steel Sheet Used Should Be 0.6Mm Thick As Per Is-513 1994. It Should Have Scratch Hardness Of 3 Kgs As Bs-3900 Part E2 1970, Is-101. It Should Sustain Salt Spray Test Of 1000 Hrs. As Is 101. Overall Size For The 4 Drawer Filing Cab : 1320 Mm (H) X 470 Mm (W) X 620 Mm (D) , Steel Almirah , It Should Have Multi Bend Construction With Interlocking Design And Full Length Over Lapping Doors And Sides, Three Way Bolting Mechanism. All Steel Components Should Undergo Eight Tank Anti Rust Treatment And Oven Backed Epoxy Polyester Powder Coated With 50-60 Dry Film Thickness. The Crca Steel Sheet User For The Body Is Of 20 Swg / Gauge, As Per Is-513 1994. It Has 5 Shelves Made Of 22 Swg / Gauge Crca Steel. It Has Six Lever Zink Plated Lock. It Has Scratch Hardness Of 3 Kgs As Bs- 3900 Part E2 1970, Is- 101. It Sustains Salt Spray Test Of 1000 Hrs. As Per Is 101. It Should Have 4 Shelves Made Of 0.8 Mm Thick Crca Steel Sheet. It Should Have Six Lever Mazak Zink Plated Lock. It Should Sustain Salt Spray Test Of 1000 Hrs. As Per Is 101. Overall Size : 198.0 Cm (H) X 91.5 Cm (W) X 48.55 Cm (D). It Has Scratch Hardness Of 3 Kgs As Bs-3900 Part E2 1970, Is-101. It Sustains Salt Spray Test Of 1000 Hrs. As Per Is 101. It Should Have 4 Shelves Made Of 0.8 Mm Thick Crca Steel Sheet. , Visitor Chair , The Seat Shall Be Made Up Of 1.2Cm. Thick Hot Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam. The Back Shall Be Made Up 1.2Cm. Thick Hot Pressed Plywood Upholstered With Replaceable Fabric Upholstery Covers And Moulded Polyurethane Foam. The Back Shall Be 1.2Cm Hot Pressed Plywood Upholstered With Replaceable Fabric Or Synthetic Leather Upholstery Covers And Moulded Polyurethane Foam. Back Size 48Cm(W) X 64.5Cm (H), Seat Size 51.0Cm(W)X48.0Cm(D) Polyurethane Foam: The Polyurethane Foam For Seat And Back Shall Be Moulded With Density =45 +/-2 Kg/M3 And Hardness=16 +/-2Kgf. Armrests (Adjustable): The Armrest Top Shall Be Made Of Moulded Polyurethane (P.U.) And Mounted On To A Drop Lift Height Adjustable Type M.S. Tubular Armrest Support Chrome Plated. The Arm Support Should Have Static Vertical Adjustment Of +/- 1.5+/-0.05Cm. Fixed Backrest: The Backrest Should Consist Of A Fixed Type Mechanism. Leg Frame Assembly: The Leg Frame Welded Assembly Should Be Chrome Plated, Made From 3.5+/-0.03Cmx1.5+/-0.02Cmx0.16+/-0.0128Cm Thick Elliptical M.S.Erw Tube And Must Be Provided With A Base Plate For Fixed Seating. , Book Shelves , It Should Have Multi Bend Construction With Press Fit Fasteners Free Design. It Should Have 10 Lever Cam Lock. Door Should Have Equalizing Scissor Mechanism For Easy Opening And Closing. All Steel Components Should Undergo Eight Tank Antirust Treatment And Oven Baked Epoxy Polyester Powder Coated With 50-60 Dry Film Thickness. The Crca Steel Sheet Used For The Top Should Be 0.8Mm Thick, As Per Is-513 1994. The Bookcase Should Have Clear Opening Of 330Mm. It Should Have Removable Glass Door With 3 Mm Glass (4 Nos.). It Should Have 4 Shelves With Stiffener. It Should Have Scratch Hardness Of 3 Kgs As Bs-3900 Part E2 Overall Size 174.2Cm(H) X 91.4Cm (W) X 32.0Cm(D) , Table For Judges Category , Supplying And Placing In Position Main Desk Of The Following Specifications. The Main Desk Shall Be Of Size 1800 Width Mm X 900 Depth Mm X 750 Height Mm. The Table Top Shall Be 25 Mm Thick Mfc (Melamine Faced Chipboard) Also There Should Be 30 Mm Mdf (Medium Density Fiberboard) Black Pad. The Modesty Panel Shall Be Of 18 Mm Thick Mfc (Melamine Faced Chipboard).The Leg Of The Main Desk Shall Be Of 25 Mm Mfc Plus 30 Mm Mdf Right And Left Pad. The Main Table Should Be Of Duck Noise Profile Edge In Order To Enhance The Workspace Aesthetics. Supplying And Placing In Position Joining Table Of The Following Specifications. The Joining Table Rhs Shall Be Of Size 1050 Width Mm X 1200 Depth Mm X 750 Height Mm. The Top Panel Shall Be 25 Mm Thick With Mfc (Melamine Faced Chipboard).The Leg Of The Joining Table Shall Be Of Metal. Polyurethane Coated Joining Table. Supplying And Placing In Position Mobile Pedestal Of The Following Specifications. The Mobile Pedestal Size Shall Be 400 Width Mm X 560 Depth Mm X 560 Height Mm. The Top Panel Shall Be 25 Mm Thick Mfc ( Melamine Faced Chipboard) Plus All The Other Panels Shall Be 18 Mm Thick Coated With Mfc (Melamine Faced Chipboard). In Mobile Pedestal All Other Panels Shall Be Of 18 Mm Thick Mfc (Melamine Faced Chipboard).In Mobile Pedestal Lock And Castors Shall Be Provided. The Handle Shall Be Of Metal. , Side Unit:- Supplying And Placing In Position Free Standing Return Desk Of The Following Specifications. The Return Desk Size Shall Be 1200 Width Mm X 600 Depth Mm X 730 Height Mm. The Top Panel Shall 25 Mm Thick Mfc (Melamine Faced Chipboard) .The Modesty Panel Shall Be 18 Mm Thick Mfc Coated. The Leg Of The Return Desk Shall Be 25 Mm Thick Mfc (Melamine Faced Chipboard) Plus The Right And Left Pad Should Be 30 Mm Thick Mdf (Medium Density Fiber) Coated. Supplying And Placing In Position Bookcase Of The Following Specifications. The Bookcase Size Shall Be 790 Width Mm X 400 Depth Mm X 2200 Height Mm. The Top Panel Shall Be 25 Mm Thick Mfc (Melamine Faced Chipboard) Plus The Bottom Panel Shall Be 25 Mm Mfc Coated. The Wood Door Panels Shall Be 18 Mm Thick Mfc .The Glass Door Panels Shall Be Of 5 Mm Thick Plus All The Other Panels Should Be 18 Mm Thick Mfc (Melamine Faced Chipboard).The Handles Shall Be Of Metal. The Bookcase Unit Provides Ample Amount Of Storage. , Back Unit :- The Supplying And Placing In Position Back Unit Of The Following Specifications. Back Unit Size Shall Be 1400 Width Mm X 470 Depth Mm X 760 Height Mm. The Top Panel Size Shall Be 25 Mm Thick Mfc (Melamine Faced Chipboard). The Door Panels And All Other Panels Should Be 18 Mm Thick Mfc (Melamine Faced Chipboard) .The Handle Shall Be Of Metal. , Single Bed For Guest House , Single Bed With 1 Side Table Having Overall Size :Length- 2060.0 Mm Xwidth - 1131.0 Mm Xheight-930.0 Mm. Material: Bed Structure Shall Consist Of Metal Framesmade Ofm.S. Channels In 1.0 Mm Thickness. Horizontal Plinths And Bottom Plinth Are To Be Made Of 25 Mm Thickprelaminated Particle Board. Head Board Isto Be Made Of 18 Mm Thick Prelaminated Particleboard With Imported H.D.F. Foil Wrapped Decorative Trims Fixedto It.Tail Board Is To Be Made Of 18 Mm Thick Prelaminated Particle Board With Imported H.D.F. Foil Wrapped Decorative Trims Fixed To It. Side Rail Is To Be Made Of 18 Mm Thick Prelaminated Particle Boardwith Imported H.D.F. Foil Wrapped Decorative Trims Fixed On To It. Mattress Panels Of Bed Are To Bemade Of 18 Mm Thick Prelaminated Particle Board With All The Exposed Edges Are Edge Banded With 0.8 Mm Thick Pvc Edge Banding. Construction :Knock Down Construction. Finish :18 Mm Thick Prelaminated Article Board Is In Walnut Shade. Metal Frames Are To Be Powder Coated In Shade Mat Black To Thethickness Of 50 Microns(+-10). Bedside Table Havingoverall Size :Depth- 450.0 Mm Xwidth - 440.0 Mm Xheight- 510.0 Mm Material. , Bed Side Table For Guest House , Body And Drawer Panels Of Bed Side Table Are To Be Made Of 18 Mm Thick. Prelaminated Particle Board. All The Exposed Edges Areto Be Edge Banded With 0.8 Mm Thick Pvc Edge Banding. Side Panels Are To Bemade Of 18 Mm Thick Prelaminated Particle Board With Imported H.D.F. Foil Wrapped Decorative Trim Fixed On To It. Hardware : The High Quality Hardware Are To Beused Like Roller Slides, Hinges , Minifix, Dowels Is Of Make Hettich. Construction :Knock Down Construction. Finish :.18 Mm Thick Prelaminated Particle Board Is In Walnut Shade. , Executive Chairs , Executive Revolving Chair With Headrest: Seat/Back Assembly: Shall Be Made Up Of Insert Moulded Polyurethane Foam Upholstered With Foam Laminated Mesh Fabric. The Insert Moulded Foam Is Assembled Over A Load Bearing Plastic Seat Cover. The Back Is Made Up Of Two Pieces Injection Moulded Frame. The Inner Frame Should Be Upholstered With Mesh Fabric And Mounted On The Main Assembly. Size: 71 Cm(W) X 71 Cm(D) X 115.5-131 Cm (H) Seat Height: 45-54Polyurethane Foam : The Polyurethane Foam Shall Be Moulded In Density 75 +/- 4Kg/M3,. Armrests :The Armrest Top Should Be Injected Moulded In Polyurethane And Mounted On The Injection Moulded Height Adjustable Type Armrest. The Armrest Height Should Be Adjustable Up To4.5+-0.5 Cm In Three Steps And Width Adjustable Up To 20Mm. Front Pivot Synchromechanism :The Synchronized Mechanism Shall Be Designed With The Following Features:360° Revolving Type. Front Pivot For Tilt With Feet Resting On Ground Ensuring More Comfort. Tilt Tension Adjustment. 3 Position Locking With Anti-Shock. Single Point Control.Make Loma Connecting Spine Backrest: Spine Backrest Shall Be Made Of Aluminum Die Cast Piece Connecting Back With Mechanism. Adjustable Neck Rest Assembly: Neck Rest Assembly Shall Be Made Of Polyurethane Foam Upholstered With Foam Laminated Mesh Fabric. The Neck Rest Assembly Shall Be Mounted On The Top Of Back. It Shall Be Adjustable Up To 4.5+-0.5Cm Up-Down And Has Angular Adjustment Of 30 Degree +-2 Degrees. Pneumatic Height Adjustment:The Pneumatic Height Adjustment Shall Have An Adjustment Stroke Of 9.0 Cm. Pedestal: The Pedestal Shall Be Die Castaluminum Fitted With 5 No’S Twin Wheel Castors. The Pedestal Pitch-Center Dia. Is 65.0Cm. Twin Wheel Castor :5 Nos. Twin Wheel Castors Shall Be Injection Moulded In Black Ppand Assembled To Aluminum Pedestal. , Centre Table For High Court. , Centre Table With Dimensions Of 1000X680x 450 Having 8 Mm Top Tempered Glass, Bottom Glass Shall Be 6Mm Tempered Glass. Understructure Shall Be Sliver Powder Coated. Glass Shall Be Connected With Under Struce With M8 Uv Disc.Shall Have A Load Bearing Capacity 30 Kgs. , Slotted Angle Rack:- Supply And Installation Of Slotted Angle Rack Having Shelves Material 0.8 Mm Thick Ms Sheet Conforming To Commercial Quality Cr-1, Grade 340 Of Is 513 , Angle Size Of 40X40x2mm ,Ground Clearance Is 55Mm +/-2 , With Powder Coated To Avoid Rust & Corrosion. Dimensions Are H 1830Mm , W 915Mm & D 457Mm. , Computer Table For Operator:- Providing And Fixing In Position Table Size B. 1350X600x750mm Having 25Mm Thick Post Formed Top Of Particle Board Flat Pressed Three Layered Medium Density Grade-Ii Confirming To Is :3087 Having Necessary Provision For Wire Management Data / Computer/ Telephone Cabling Having Modesty And Vertical Panel In 18Mm Thick Prelaminated Particle Board Three Layered Medium Density Grade-Ii, Type –Ii Confirming To Is :12823 Complete As Per Salient Technical Features, Specifications, Drawings And Directions Of The Officer-In-Charge And With Pedestal Storage Providing & Fixing Pedestal Unit Of Size 450X500x725mm Having 1 Drawer At Top And Bottom Having Open Able Shutter Made Of 18Mm Thick Prelaminated Particle Board. The Inner Drawer Shall Be Made Of Steel Duly Powder Coated & Shall Have Proper Locking Arrangement With Drawer Sliding On Nylon Rollers Channels. The Drawer Shall Also Have Pencil Tray Made Up Abc Plastic With Separate Section For Pencil & Stationary Etc Of Size 300X150.With Cpu Trolley Having Providing And Fixing Cpu Trolley Made Of Size 220X250x250 Mm Having Adjustable Width And Lockable Castors At Base, Made Of 0.9 Mm Thick Complete As Per Salient Technical Features, & Keyboard Tray Of Eepcco/ Ozone Or Better, Size 600X350 Mm Made Out Of 25 Mm Thick Particle Board With Post Formed Decorative Laminate On Top And Having Balancing Lamination On The Unexposed Face In Work Stations, Executive Table Or Side Units In Approved Colour And Texture As Per Salient Technical Features, Specifications. , Footrest:- Ergo Rest Foot Rest: Angle Adjustable: Promotes Stress Free Posture: Slip Resistance Surface: Platform Size 445Mm(W)X295mm(D) , Boltless Racks:- Product Specification For Boltless Shelving - Depth (, Mm) 500 , Width (Mm) 1300, L/L Height (Mm) 425 Mm & 349 Mm In Top Shelf, System Height (Mm)2500, Upright Height (Mm) 2495 , Self Loading Capacity 142 . Udl, With 6.1 Upright :- Upright Type - Upright G50, Profile , ‘T’ Profile, Profile Size 50 Mm X 37 Mm, No Of Bends 9 Bends, Level Adjustability 25 Mm, Material Grade Min Ys=210 Mpa, Mfg Process Roll Forming, Finish Powder Coated Finish On Zinc Coated Steel, Colour Oxford Blue, 6.2 Shelf: Width 1300 Mm, Depth 500 Mm, Material Zinc Coated, Shelf Height 32Mm,No Of Bends 14, Mfg Process Roll Formed, Fasteners No, Mounting ‘4’ Nos Of Clips Per Shelf ( No Bolting), Surface Finish Zinc Coated Spangle Free Fine Finish, 6.3 Bracings Section Flat Mid Rib And End Bends, Mfg Process Press Forming, Connectivity Hooking & Pin It, Surface Finish Zinc Coated, Shelf Clip Profile Section 24 X 8 X 35Mm, Material Gi, Mfg Process Blanking & Punching, No Of Bend 2, Connectivity Insertion, Surface Finish Galvanized, 6.5 Stability Member : Profile Section 20 X 25 X 54Mm, Material Zinc Coated Mfg Processnotching & Folding, No Of Bends 2, Connectivity Hooking & Pin It, Structural Analysis And Testing:- •The Racks / Shelves/ Selves Be Tested For Structural Rigidity And Safety. Design Analysis And Development Activities Are Validated And Approved By Premier Structural Institutes And Organization. Quality Assurance By The Bidder/ Oem:- • Robust Quality Assurance Programmed Is Carefully Overseen By Our Highly-Qualified And Dedicated In-House Quality Assurance Team. • The High-Quality Raw Materials Beutilize And Are To Be Sourced From World-Class Steel Manufacturers Across The World. • The Powder Meant For Finish Be Tested For Its Chemical And Physical Properties For Every Batch. The Fasteners Undergo Random Sampling Be Tested For Its Dimensions. • There Should Be Quality Management Certificate Of Iso 9001: 2008, Certified By Tuv Nord.
|
