|
Construction Of 02 Additional Class Rooms In Govt Girls Sss Sardargarh Block Amet - Part ACivil Work Based on PWD BSR 2022 For Jaipur Circle) 2 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils 3 Supply & Stacking good soil of earth at site completeincluding loading unloading & Transportation etc.Good soil of earth Filling available excavated earth (excluding rock) in trenches,plinth side of foundation etc. in layers not exceeding 20 cm. indepth, consolidating each deposited layer by ramming andwatering including lead up to 50 meter and with all lift. 4 Providing and laying in position cement concrete includingcuring, compaction etc. complete in specified grade excludingthe cost of centering and shuttering - All work up to plinthlevel. M10 grade Nominal Mix1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate40mm nominal size). 5 Providing and laying in position cement concrete includingcuring, compaction etc. complete in specified grade excludingthe cost of centering and shuttering - All work up to plinthlevel. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size). 6 Providing and laying cement concrete including curing,compaction etc. complete in retaining walls, return walls,walls (any thickness) including attached pilasters, columns,piers, abutments, pillars, posts, struts, buttresses, string orlacing courses, parapets, coping, bed blocks, anchor blocks,plain window sills, fillets, levelling course etc up to floor fivelevel excluding the cost of centering and shuttering. M20 grade Nominal Mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size). 7 Providing and laying in position specified grade of cementconcrete for all RCC structural elements upto plinth levelincluding curing, compaction, finishing with rendering incement sand mortar 1:3 (1 cement: 3 coarse sand) and makinggood the joints and cost of plastizers( if required) excludingthe cost of centering, shuttering and reinforcement.M20 grade Nominal Mix / Design Mix 8 Providing and laying in position specified grade of cementconcrete for all RCC structural elements upto plinth levelincluding curing, compaction, finishing with rendering incement sand mortar 1:3 (1 cement: 3 coarse sand) and makinggood the joints and cost of plastizers( if required) excludingthe cost of centering, shuttering and reinforcement.M20 grade Nominal Mix / Design Mix Add extra for providing richer mixes respectively at all floorlevels Providing M-25 grade concrete by using cement as per codalprovision instead of M-20 grade design mix. 9 Providing and laying in position specified grade of cementconcrete for RCC structural elements upto floor five levelincluding curing, compaction, finishing with rendering incement sand mortar 1:3 (1 cement: 3 coarse sand) and makinggood the joints and cost of plastizers( if required) excludingthe cost of centering, shuttering and reinforcement for Beams,suspended floors, roofs, griders having slopes up to 15º,landings, balconies, shelves, chajjas, lintels, bands, plainwindows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix 10 Providing and laying in position specified grade of cementconcrete for RCC structural elements upto floor five levelincluding curing, compaction, finishing with rendering incement sand mortar 1:3 (1 cement: 3 coarse sand) and makinggood the joints and cost of plastizers (if required ) excludingthe cost of centering, shuttering and reinforcement for Walls(any thickness) including attached pilasters, buttresses, plinthand string courses, fillets, columns, pillars, piers, abutments,posts and struts etc.M20 grade Nominal Mix / Design Mix Add extra for providing richer mixes respectively at all floorlevels Providing M-25 grade concrete by using cement as per codalprovision instead of M-20 grade design mix. 11 Centering and Shuttering with plywood or steel sheetsincluding strutting, propping bracing both ways and removalof formwork for foundation , footings, strap beam, raft , basesof columns etc. 12 Centering & shuttering with plywood or steel sheets includingstrutting, propping bracing both ways with steel props andremoval of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies,girders, cantilevers, bands, coping bed plates, anchor blocks,sills, chhajjas, lintel, beam, plinth beam etc. 13 Centering & shuttering with plywood or steel sheets includingstrutting, propping bracing both ways with steel props andremoval of formwork for upto floor five level for :Columns, pillars, posts and struts etc. 14 Providing and fabricating reinforcement for R.C.C. workincluding straightening, cutting, bending, placing in positionand binding (including cost of binding wire) all complete up tofloor five level.Thermo-mechanically Treated bars (Conforming of relevent IScode) 15 Brick work with clay flyash F.P.S. brick (IS 13757- 1993 ) ofclass designation 75 in superstructure above plinth level uptofloor five level in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) 16 Random Rubble stone masonry for with hard stone infoundation and plinth in Cement Sand mortar above 30 CMthick wall in:Cement Mortar 1:6 ( 1-Cement : 6-Sand). 17 Providing and fixing T-iron frames for doors, windows andventilators of mild steel Tee-sections, joints mitred and weldedwith 15x3 mm lugs 10cm long embedded in cement concreteblocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6graded stone aggregate 20 mm nominal size) or with woodenplugs and screws or rawl plugs and screws or with fixing clipsor with bolts and nuts as require including fixing of necessarybutt hinges and screws and applying a priming coat ofapproved steel primer. 18 Providing and fixing M.S. sheet 1mm thick single leaf doorshutter in angle iron frame 35x35x5mm suitabilly diagonallybraced with 25x3mm flat iron above and below lock rail ofsize 50x5mm beading extra including all fittings, as perdirection of Engg. incharge but excluding cost of chowkhats:including two coats of anit-corrosive red oxide primer paint Add extra for double leaf shutters. 19 Providing and fixing steel glazed doors windows andventilator shutters of standard rolled steel section (IS 1038-1983) joints mitred and welded with steel lugs 13x3mm, 10cm.long embedded in cement concrete block 15x10x10cm. of1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate20mm nominal size) or with wooden plugs and screws or rawlplugs and screws with fixing clips or with bolts and nuts asrequired including providing and fixing of plain glass panes4mm thick with cooper glazing clips and special metal sashputty of approved make or metal beading with screwscomplete including priming coat of approval steel primer,excluding the cost of metal beading and other fitting exceptnecessary hinges of pivots steel handles peg stay etc. asrequired :Partly fixed and partly openable [ fixed area not to exceed33%] 20 Supplying and fixing fixed wire gauge of 14 mesh x 24 gaugeto the metal frame of rolled section by metal beading 20x3mmwith suitable screw at not exceeding 150mm distance. 21 Providing and fixing Square bars or other flat welded towindow, ventilatiors etc. 22 Grading roof for water proofing treatment with waterproffing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 gradedstone aggregate 20 mm nominal size) 23 Providing & laying broken glazed titles on roof ( brokenglazed tiles not less than 9 Kg/Sqm) on top of hot bitumen @1.7 Kg/Sqm. (1.40 Kg of VG-40 (30/40 )grade and 0.30Kg/Sqm. Of VG-10 (80/100) grade) and joints filled withcement mortar 1 :2 (1 cement:2 marble dust mixed with waterproofing compund all complete as per direction of Engineerin-charge. 24 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 stone aggregate 10mm and down gauge)including finishing with cement mortar 1:3 (1 cement : 3 finesand) as per standard design : 25 Chequerred precast cement concrete tiles 22 mm thick infootpath & courtyard jointed with neat cement slurry mixedwith pigment to match the shade of tiles including rubbingand cleaning etc. complete on 20 mm thick bed of cementmortar 1:4 (1 cement : 4 coarse sand) Light shade using shade cement. 26 Kota stone slab flooring 25 mm thick over 20 mm (average)thick base laid over and jointed with grey cement slurrymixed with pigment to match the shade of the slab includingrubbing and polishing complete with base of cement mortar 1: 4 (1 cement : 4 coarse sand) For area of each slab from 2001 to 5000 Sq.Cm 27 Kota stone slabs 25 mm thick in risers of steps, skirting, dadoand pillars laid on 12 mm (average) thick cement mortar 1:3 (1cement 3 coarse sand) and jointed with grey cement slurrymixed with pigment to match the shade of the slabs, includingrubbing and polishing complete For area of each slab upto 2001 Sqcm 28 Random rubble dry stone Kharanja under floor. 29 Plaster on new surface on walls in cement sand mortar 1:6including racking of joint etc. complete fine finish :12mm thick. 30 Plaster on new surface on walls in cement sand mortar 1:6including racking of joint etc. complete fine finish :20mm thick. 31 6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine sand) 32 Providing and applying white cement based putty overplastered surface to prepare the surface even and smoothcomplete New Plastered Surface (three or more coats) 33 Distempering with oil bound washable distemper of approvedbrand and manufacture to give an even shade including allscaffolding:New work (two or more coats) over and includingscrapping and priming coat with cement primer. 34 Finishing walls with Acrylic Smooth exterior paint of requiredshade including all scaffolding.New work (Two or more coat applied @ 1.67 ltr/10 sqm overand including base coat of water proofing cement paint applied@ 2.20 kg/ 10 sqm ). 35 Providing and fixing Granite stone slab mirror polished andmachine edge cut in walls, pillars, steps, Shelves, SillsCounters, Floors etc. laid on 12mm (Av.) thick base of cementmortar 1:3 (1 cement : 3 coarse sand) jointing with whitecement mortar 1:2 (1white cement : 2 marble dust) withpigment to match the shade of the marble slab includinggrinding, rubbing and polishing complete.Rajasthan Black Above 3601 Cm2 Slabs 36 Painting with synthetic enamel paint of approved brand andmanufacture to give an even shade :Two or more coats on new work 37 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2 .)approved quality /make including joining the pipe withsolvent cement rubber ring and lubricant. 110 mm dia 38 P&F rigid PVC pipe fittings (IS: 4985 mark) of approvedquality /make including joining the pipe with solvent cementrubber ring and lubricant:Bend 87 .5 110mm dia 39 Pipe Clip 110mm dia 40 Electrical Work Based on PWD BSR 2022 : Jaipur Circle 41 Wiring of 3/5 pin 6 amp. Light plug point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694)and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)in recessed ISI markedMMS ( IS:9537 P - III ) vergin material PVC conduit & it"s all accessories( J.B. , Bends etc.) , round tiles,18 SWG G.I. box with earth terminal of required size,6 Aswitch, 3/5 pin 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet (IS : 2036 -1995),Al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by Engineer in charge,making connections, testing etc. complete as required. For specification of copperConductor,Phenolic Laminated sheet"s & Electrical/ Wiring accessoriesrefer Chapter E - 04, E - 05 & E - 07. For additional technical parameters of products/ work, referAnnexure "A" attached with this BSR . on board Light point 42 Medium point (up to 6 mtr) 43 Long point (up to 10 mtr) 44 Wiring of 3/5 pin 6 amp. Light plug point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694)and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)in recessed ISI markedMMS ( IS:9537 P - III ) vergin material PVC conduit & it"s all accessories( J.B. , Bends etc.) , round tiles,18 SWG G.I. box with earth terminal of required size,6 Aswitch, 3/5 pin 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet (IS : 2036 -1995),Al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by Engineer in charge,making connections, testing etc. complete as required. For specification of copperConductor,Phenolic Laminated sheet"s & Electrical/ Wiring accessoriesrefer Chapter E - 04, E - 05 & E - 07. For additional technical parameters of products/ work, referAnnexure "A" attached with this BSR . on board 45 S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit as per PWD specification for electrical Works along with its accessories (IS: 3419 ) as requiredinrecess includingcutting the wall, covering conduit and making good the same as required. All relative and latest acceptance tests reports by any NABL accredited lab for the conduit shall be submitted before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, referAnnexure "A" attached with this BSR . MMS (9537 P-111)PVC condute.25mm. 46 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.99% purity copper, class 5 stranding in acc. to IEC 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4,, in existingsurface or recessed PVC/ MS conduit/casing capping includingall as per pre approved by Engineer in charge,making connections, etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of products/ work, referAnnexure "A" attached with this BSR .2 x 1.5 sq. mm 47 2 x 2.5 sq. mm 48 Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load andsite requirement) 4KV impulse withstand voltage,as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted withexisting distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A ratingincluding making connections, testing etc. as required.. OEM shall have submitNABL / CPRI / ERDA accrediated lab test reportsbefore execution & All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR .6A TO 32A rating. 49 Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure "A" attached with this BSR.Metal door (single phase) IK-09 and IP-43 with Metal end box6 Way (6+2 50 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from polycarbonate /extruded aluminium powder coatedhousing with in built driver, Power Consumption of18W/20W ,system lumen efficacy ≥ 120 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% ,p.f.≥0.95, CRI >80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. 1170mm(+/-10%) LED batten with min. lumen output 2200 lm 51 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-ArrmouredAluminiumcable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV withH4- Grade electrolyticaluminium conductor confirming to IS 8130 of purity >99.6 %,Inner / outer sheath confirming to IS:5831in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) includingtesting etc. as required of following size. OEM must have it"s own in house NABL accrediated Laboratory for testing procedure as per IS:10810. For additional technical parameters of product / work refer Annexure "A" attached with this BSR6.0 Sq. mm4 core 52 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-ArrmouredAluminiumcable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV withH4- Grade electrolyticaluminium conductor confirming to IS 8130 of purity >99.6 %,Inner / outer sheath confirming to IS:5831in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) includingtesting etc. as required of following size. OEM must have it"s own in house NABL accrediated Laboratory for testing procedure as per IS:10810. For additional technical parameters of product / work refer Annexure "A" attached with this BSR6.0 Sq. mm4 core 53 Providing & Fixing ofBEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanConforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR .1200 mm Sweep BEE 2 Star rated (service value >=4.5 to < 5 ) 54 Providing & Fixing of ISI marked (IS:1258) batten/angle lampholder with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screwsincluding making connection testing etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 55 P & F 1.2mm thickM.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure "A" attached with this BSR 56 Providing & Fixing of 240/415 V isolator as per PWD specification for electrical Works with ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization catagory, 4KV impulse withstand voltage,true contact indication,Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting,minimum phase termination capacity of 35sq.mm. , label holding facility , IP 20 contact protection and fitted with existing distribution board / sheetincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab test reportsbefore execution & All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . Double pole isolator30 A / 40 A rating 57 Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith IP-20 rating ,includingall as per pre approved by Engineer in charge,making connections, testing etc. as required.For additional technical parameters of product / work refer Annexure "A" attached with this BSR 5 step fan regulator 2 Module 360 dgree rotating
|
