Tender For Construction Of Kgbv Type-Iv (Class 9 To 12) Saipau Dholpur - Constructin Kgbv Type Iv ( Class 9- ... in India

Work Detail

Tender For Construction Of Kgbv Type-Iv (Class 9 To 12) Saipau Dholpur - CONSTRUCTIN KGBV TYPE IV ( CLASS 9-12) SAIPAU IN COMPLIANCE OF HONOURABLE CM BUDGET ANNOUCEMENT UNDER NABARD RIDF XXVII / THE STATE BUDGET HEAD Sl. No. Item Description 1 Earth work in excavation by mechanical means (Hydraulic Excavator ) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds of soils 2 Supply & stacking good earth at site complete including loading , unloading and transportation etc &Filling available excavated earth (excluding rock) in trenches plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead upto 50 Mtr. and lift upto 1.5 Mtr. 3 Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:4:8 (1 cement:4 Coarse sand :8 gradeed stone aggregate 40 mm nominal size). 4 Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth levelM 10 grade nominal Mix1:3:6(1 cement:3 Coarse sand : 6 gradeed stone aggregate 20 mm nominal size). 5 Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size). 6 Providing and laying in position specified grade ofcement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement M20 grade Nominal Mix / Design Mix 7 Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor r Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix 8 Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor ColumnsM20 grade Nominal Mix / Design Mix 9 Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation, footings, strap beam, raft, bases of columns etc. 10 Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : 11 Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 12 Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : Columns, pillars, posts and struts etc. 13 Providing and fabricating reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding(including cost of binding wire) all complete up to floor five level. TMT bars (conforming of relevent IS code) 14 Brick work with Fly ash F.P.S. Bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in Cementmortar 1: 6 (1 cement : 6 coarse sand) 15 Half Brick work with mechanised autoclaved flyash lime bricks conforming to IS: 12894 :2002 of class designation 75 in superstructure above plinth level upto floor V level in. Cement mortar 1 : 6 (1 cement : 6 coarse sand) 16 Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in cement mortat 1:6 (1-Cement: 6- Sand) 17 Supplying and fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine cut edges Kota stone minimum 30mm thick. 18 Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Jalore P White / S White\Z Black / Rosy pink color Above 3601 SqCm Slabs 19 Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS : 15622of size 200mm x 300mm in walls, floors steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match theshade of the tile complete (excluding the cost of cementplaster on walls and pillar.)Extra for using Marble printed / Granite shade or dark shade tiles instead of white, grey, ivory, fume red brown,light green, light blue and other light shades in glazedtiles and MAT finished tiles, Extra for using size above 200x300mm in glazed tiles andfor using 400mm x 400mm MAT finished tiles in place of300mm x 300mm size 20 Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in thewhite cement mixed with pigment to match the shadeof the tile complete (including the cost of cement mortar bed 1:4) 21 Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure "A" 35 mm thick. Commercial Veneer both side 22 Providing double leaf door shutter instead of single leaf door shutter 23 Extra for cutting rebate in flush door shutters for making double leaf shutter (Total area of the shutter to be measured) 24 Extra for providing external lipping with 2nd class teak wood battens 6mm minimum depth on all edges of shutters (over all area of door shutter to be measured) 25 Providing and fixing curtain rods of 1.25 mm thick chormium plated brass plate, with two chromium plated brass brackets fixed with c.p. brass screws and wooden plugs, etc. wherever necessary complete 20mm 26 Providing and fixing in position collapsible steel shutters with vertical M.S. Channels 20 x 10 x 2mm and bracket with flat iron diagonals 20 x 5mm. size with top and bottom rail of T-iron 40 x 40 x 6mm. with 40mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured and paid as per outer dimension).Collapsible steel shutters 27 Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitred welded and grinded including hold fast of steel lugs 13mm x 3mm and 15 Cm longembedded in C C block 15 x 10 x 10 Cm of 1:3:6 nominal concreteand including fixing of pivoted hinges of superior quality, windowshutters made out of 50 x 25.0 mm hollow steel section 15 mm paitamof 18 gauge thickness, joint mitred and grinded including 10mm x10mm square bars welded to frame for paitam fixing float glass 4mmthick panes with glazing clips and metal sash putty and fixing ofshutters frames peg stay, U shape handle 100 mm long, tower bolts100 mm long of steel powder coated superior quality including fixingand jointing with frame hinges priming coat with steel primer completein all respect as per direction of Engineer-in –chargeWindow openable 28 Extra for additional shutter in pipe section windows with wire gauge 14 mesh x 24 gaug 29 Providing and fixing pressed steel door frames confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applyinga coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4(M15 grade) complete as directed by Engineer-in-charge : 30 ProfileB 31 Providing and fixing in CM 1 : 4 double paitam (rebated) stone door window and ventilator frames of approved quarry : 32 Size 100 x 75 mm. 33 Guard Bars: P&F square bars or other flat welded to window/ventilators etc., Guard bar 12 x12mm 34 Providing and fixing M.S. sheet 1 mm thick single leaf door shutter in angle iron frame 35X35X5mm suitabilly diagonally braced with 25X3mm flat iron above and below lock rail of size 50X5mm beading extra including all fittings as peer direction of engg. incharge but excluding cost of chowkhats including two coats of anit- corrosive red oxide primer paint 35 Providing and fixing of double leaf steel shutter for cupboard, the frame is made of pressed steel ISI section 80x25 mmx 1.25 mm thick with 1.00 mm MS sheet to spot welded including holdfasts of 15x3mm, MS oxidized fittings such as butt higes, sliding doors bolts, handles, tower bolts and twin peg etc complete including applying priming coat of approved steelprimer of red oxide zinc chromate and spray paintin in approved shade with deco paint of approved quality complete as per direction of Engineer In Charge 36 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 37 Grading roof for water proofing treatment withwater proffing compound: Cement concrete 1: 2: 4 (1 cement: 2 Course sand: 4 Greded stone aggregate 20 mm nominal size) 38 Crazy marble stone flooring 20mm thick marble stone withblack or of specified colour topping including filling the gapswith cement marble chips mix in proportion of 4 : 7 (4cement7 white black or white or black marble chips) size from 1mm to4mm by volume and under layer of 25mm thick cementconcrete [1:2:4, graded stone aggregate 12.5mm nominal size]rubbing and polishing and cement slurry etc. complete :In ordinary cement. 39 Providing gola 75x75 mm in cement concrete 1:2:4 ( 1 cement ; 2 coarse sand : 4 stone aggregate 10 mm and down gauge) including finishing with cement mortar 1:3 ( 1 cement : 3 fine sand ) as per standard design 40 Making khurras450 x 450mmwith average minimum thickness 50 mm cement concrete 1:2:4 over P.V.C sheet 1 mtr. X 1 x 40micron finished with 12mm cement plaster 1 : 3 and one coat of neat cement rounding edges and making and finishing the out let complete 41 Kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand) For area of each slab from 2001 to 5000 Sq.Cm 42 Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete(For area of each slab upto 2001Sqcm) 43 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles includingrubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) Light shade using shade cement.P 44 Filling of sunk portion of roof with earthen postof required height including filling voids with 1;3;6 light concrete, using brick bats complete leveling and dressing the surface by 50mm thick cement concrete 1;2:4 as per specification 45 Toilet Block 46 Random rubble dry stone Kharanja under floor. 47 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished : 48 20 mm thick 49 12mm Thick. 50 6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3 - fine sand) 51 Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 52 New Plastered Surface (three or more coats) 53 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: 54 Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. 55 A. Ceiling And Inner wall Area 56 Finishing walls with textured exterior paint of required shade as per approved colour complete as per manufacturers specificationsincluding primer coat and protecting coat 57 Roller Finish av. thickness 400 to 500 microns. 58 Applying priming coat with ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood. 59 PANTING ON DOORS & WINDOWS:- Painting with syntheitic enamel paint of approved brand and manufacture in all shade to give an even shadenew steel work (2 or more coat on new work). 60 Providing and fixing to existing door frames. 30mm thick factory made solid panel PVC door shutterconsisting of frame made out of M.S. tubes of 19 gaugethickness and size of 19mm x 19mm for stiles and 15 mmx15mm , top & bottom rails. M.S .frame shall have a coat ofsteel primers of approved make and manufacture M.S. framecovered with 5mm thick heat moulded PVC „C channel of size30mm thickness, 70mm width out of which 50mm shall be flatand 20mm shall be tapered in 45 degree angle on either sideforming stiles; and 5mm thick, 95mm wide PVC sheet out ofwhich 75 mm shall be flat and 20mm shall be tapered in 45degree on the inner side to form top and bottom rail and115mm wide PVC sheet out of which 75 mm shall be flat and20mm shall be tapered on both sides to form lock rail. Topbottom and lock rails shall be provided either side of the panel.10mm (5mm x 2) thick, 20mm wide cross PVC sheet shall beprovided as gap insert for top rail & bottom rail. Panelling of5mm thick PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with 7mm (5mm +2mm) thick x15mm wide PVC sheet bending on inner side, and joinedtogether with solvent cement adhesive. An additional 5mmthick PVC strip of 20mm width is to be stuck on the interiorside of the „C Channel using PVC solvent adhesive etc.complete as per direction of Engineer-in-charge,manufacture‟s specification & drawing.(For W.C.andbathroom door shutter) 61 Add For Other Facility Development 62 Sanitory 63 P&F indian type white glazed vitreous china 1st quality W.c. orissa pan (IS : 2556 mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: size 530X410 mm 64 P & F European type white glazed vitreous china 1st quality W.C pan (IS : 2556 Mark) with P or S trap including cutting and making good the wall and floor 65 P&F water closet seat covers with brass hinges complete: solid PVC (IS 2548 marked) grade-I white for EWC. 66 P&F C.P. lugs for toilet seat cover. 67 P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall: PVC with PVCbend as per IS : 7231 . 68 P&F WVC wash basin (Ist quality, I.S. :2556 mark) of approved make with C.I. brackets duly painted, 1No. 15 mm c.P. pillar cock(IS:8934 mark)& 32 mm C.P. brass waste coupling of approved make, 25mm G.I. waste pipe complete including cutting & making good the wall size 510 mmX400 mm 69 P&F kitchen & lab sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, c.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up- to floor level complete including cutting and making good the wall & floor: 1.0 mm thick salem stainless steel AISI- 304 & IS 13983-1994 kitchen sink of approved make as per engineer-in charge with large waste coupling overall size 24X18X8 inches Bowl size 20X16X8 inches 70 P&F Beveled edge Mirror of special glass of approved make (Atul/ equivalent) complete with 6mm thick asbestos cement sheet ground fixed to wooden screws and washers. Size other sizes 71 P & F Towel Rail or Ring of approved quality/ make: C.P. brass towel rail elbow type with concealed screws size 450 mm (Heavy duty) 72 P & F Grating of approved quality /make Stainless steel sheet size 125 mm dia 73 P & F jet spray for water closet with C.P. Copper tube flange of approved make 74 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) 75 20mm nominal outer dia pipes 76 25 mm nominal outer dia pipes 77 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge.(External work). 78 A.15mm dia Nominal Bore "B" class 79 B. 25mm dia Nominal Bore "B" class 80 Making connection of GI distribution branch with GI main including all fitting. Upto 25mm dia 81 P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: C.P. Brass bib cock,15mm nominal bore. 82 P & F Stop Cock (IS :8931 Mark), superior quality & of approved make: Brass 400 gm. 15mm nominal bore. 83 P & F Push Cocksuperior quality & of approved make: C.P. Brass 15mm nominal bore. 84 P & F Ball Cock (IS :1703 Mark) with Rod & P.V.C. Ball complete : Brass wt.600 gm, 25mm. 85 P&F pillar cocks(IS; 8934 mark) of superior quality and approved make. C.P. pillar cock, 15 mm dia nominal bore 86 P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15mm.Brass (IS : 8931 marked) 87 P&F 15 mm dia connection pipe of approved quality/ make PVC Pipes with nuts 450mm. 88 P&F Flush Cock/Flush valve (IS :9758) for WC of approved make CP brass 25 mm nominal bore. 89 P&F Full way valve (IS:778 Mark) or wheel valve of approved make. 90 (A)Gun metal 15 mm nominal bore. 91 (B)Gun metal 25 mm nominal bore. 92 P & F PVC Storage tank (IS 12701 marked indicating the BIS licence No.) of approved make with cover, 25mm dia 1M long G.I. Over flow pipe and 25 cm long wash out pipe with plug & socket including making connection etc complete of approved design. 93 1000 Ltr. 94 500 Ltr. 95 P& F rigid PVC Pipe (IS 4985 Mark) Class 2nd /(4 kg /sqcm) approved quality / Make including joining the pipe with solvant cement rubber ring and lubricant. 96 (A)110 mm dia. 97 (B) 160mm dia. 98 plain Tee 110mm dia 99 Door Tee 110 mm dia 100 Door "Y 110 mm dia 101 Bend 87.5 110 mmdia 102 W.C.Connector with lipring 110 mm dia 103 plain floor trap 110 mm dia 104 Gully trap 110 mm dia 105 Construction of manhole in all type of soil inner size 90X60 cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C flooring, making channels, 80 mm thick stone slab covering with 40 mm thick M-15 grade C.C flooring, cement cover with frame of 450 mm dia, earthwork etc. complete as per design including disposal of surplus earht within 50 mtr. lead. Depth up to 0.5m 106 Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. 107 Inside size 300 X 300 mm depth upto 0.5 MCement cover with frame. 108 Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C flooring, earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: 3.24.1 Size 300 Cm. dia outside & 300Cm. depth . 109 Construction of Septic Tank in all type of soil with 40 cm thick masonry with CM 1:6, 15cm thick CC bed of 1:5:10 M15 grade CC flooring & over stone slab covering, 80 mm thick slab jointing of slab in in CM 1:3, Ralthal, Kharanja 50 mm thick stone partition walls , 20 mm thick plaster in CM 1:6 finished with neat floating cement , 4 nos. CI foot rest of approved design , 2 nos 450 mm dia 25 kg each CI cover with frame earth work etc completeas per approved drawing including disposal of surplus earth within a lead of 50 Mtr. Size 400x140x150cm ( for 50 users ) 110 Construction of Septic Tank in all type of soil with 40 cm thick masonry with CM 1:6, 15cm thick CC bed of 1:5:10 M15 grade CC flooring & over stone slab covering, 80 mm thick slab jointing of slab in in CM 1:3, Ralthal, Kharanja 50 mm thick stone partition walls , 20 mm thick plaster in CM 1:6 finished with neat floating cement , 4 nos. CI foot rest of approved design , 2 nos 450 mm dia 25 kg each CI cover with frame earth work etc completeas per approved drawing including disposal of surplus earth within a lead of 50 Mtr. Size 200x100x130 cm.(for 10 users) 111 Construction of Open Surface Drain with 112mm thick brick masonry in CM 1:4,110mm thick base concrete 1:5:10, 37mm thick M-15 grade C.C. flooring ,12mm 1:4 cement plaster on all exposed faces of walls including top surface excavation & disposal of earth complete as per approved design/drawing: 150mm drain,225mmm av. Depth 112 Electric 113 Wiring of light point/ fan point/ exhaust fan point/ call bell point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694)and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)in recessed ISI markedMMS ( IS:9537 P - III ) vergin material PVC conduit & it"s all accessories( J.B. , Bends etc.) , round tiles,18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / lamp Holder/ 3 pin connector , screws etc, making connections,all as per pre approved by Engineer in charge, testing etc. complete as required.For specification of copperConductor,Phenolic Laminated sheet"s & Electrical/ Wiring accessoriesrefer Chapter E - 04, E - 05 & E - 07 . For additional technical parameters of products/ work, referAnnexure "A" attached with this BSR . 114 Short point (up to 3 mtr.) 115 Medium point (up to 6 mtr) 116 Long point (up to 10 mtr) 117 Wiring of twin control light / fan / call bell point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694)and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)in recessed ISI markedMMS ( IS:9537 P - III ) vergin material PVC conduit & it"s all accessories( J.B. , Bends etc.) , round tiles,2 nos. 18 SWG G.I. box with earth terminal,2 Nos 6 A two way switch,3 pin ceiling rose/ Lamp holder / 3 point Connector, 3.0 mm thick ISI marked phenolic laminated sheet (IS : 2036 -1995),Al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by Engineer in charge, making connections, testing etc. complete as required.For specification of copperConductor,Phenolic Laminated sheet"s & Electrical/ Wiring accessoriesrefer Chapter E - 04, E - 05 & E - 07. . For additional technical parameters of products/ work, referAnnexure "A" attached with this BSR . 118 Medium point (up to 6 mtr) 119 Wiring of 3/5 pin 6 amp. Light plug point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694)and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)in recessed ISI markedMMS ( IS:9537 P - III ) vergin material PVC conduit & it"s all accessories( J.B. , Bends etc.) , round tiles,18 SWG G.I. box with earth terminal of required size,6 Aswitch, 3/5 pin 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet (IS : 2036 -1995),Al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by Engineer in charge,making connections, testing etc. complete as required. For specification of copperConductor,Phenolic Laminated sheet"s & Electrical/ Wiring accessoriesrefer Chapter E - 04, E - 05 & E - 07. For additional technical parameters of products/ work, referAnnexure "A" attached with this BSR . 120 On board 121 S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit as per PWD specification for electrical Works along with its accessories (IS: 3419 ) as requiredinrecess includingcutting the wall, covering conduit and making good the same as required. All relative and latest acceptance tests reports by any NABL accredited lab for the conduit shall be submitted before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, referAnnexure "A" attached with this BSR . 122 25 mm dia 123 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.99% purity copper, class 5 stranding in acc. to IEC 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4,, in existingsurface or recessed PVC/ MS conduit/casing capping includingall as per pre approved by Engineer in charge,making connections, etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of products/ work, referAnnexure "A" attached with this BSR . 124 2 x 1.5 sq. mm 125 2 x 2.5 sq. mm 126 2 x 4 sqmm 127 Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load andsite requirement) 4KV impulse withstand voltage,as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted withexisting distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A ratingincluding making connections, testing etc. as required.. OEM shall have submitNABL / CPRI / ERDA accrediated lab test reportsbefore execution & All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 128 6 A to 32 A rating 129 50 A to 63A rating 130 Providing & Fixing of IK09 recessed/surface mounting heavy duty horizontal type sheet steel of 1.6 mm thickDistribution board as per PWD specificationfor electrical Works ISI marked conforming to IS-13032 & IS-8623 / conforming to IEC 61439-3. Phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal DBterminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submitNABL / CPRI / ERDA accrediated lab test reportsbefore execution & All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 131 Double door(Single Phase) 8 way 132 Double door(Single Phase) 16 way 133 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminiumhousing with in built driver, System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 134 1170mm(+/-10%) LED batten with min. lumen output 2200 lm 135 Providing & Fixing of energy efficient direct fit (Retrofit)Polycarbonate/ GlasshousingSMD Mid Power LED tube rod(with integral driver & alumn. heat sink ), on existing fixture.system lumen efficacy ≥ 100 lm/Watt output, internal surge protection of 2.5 KV ,THD < 20% ,p.f.≥0.95,CRI >80 , life time of minimum35000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80)certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR .1200mm , Min. Lumens output 2000 lmLED Tube rod with Polycarbonate Housing 136 Pipe Earthingas per IS:3043- 1987 with 3.0 Mtr. Long, 40 mm dia. " B " class G.I. Pipe IS: 1239 (Part-1) 2004, Equivalent to BS : 1387 with perforated holes of 12 mm dia ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height250 to 300 mm. and embodying the pipecomplete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 137 Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles,making connection with GI/Cu purity purity >95%thimble etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR10 SWG tinned copper. Wire 138 Providing & Fixing of Heavy duty capacitor start, copper woindDouble ball bearing900/1400 RPM single phaseExhaustfan as per PWD specification for electrical Works, conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. OEM shall be an ISO certified company. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 139 300 mm sweep (900/1400 RPM) 140 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured / Armouredaluminiumcable of 1.1 KV grade as per PWD specification for electrical Worksin existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench, on existing cable trays or on surface etc.including making necessary connection, testing etc. as required of size andas per points (a), (b), (c), mentioned below:- Un-armoured 6 sqmm 4 core 141 Providing & Fixing of ISO Certified company made BEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanas per PWD specification for electrical Works, conforming to IS:374-2019, & IS:1885 -P-V- 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required.Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 142 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) 143 Providing & Fixing of 3 Way Connector equivalent to 3 pin ceiling rose for False Ceilingas per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 144 Providing & Fixing of ISI marked (IS :3854) 16 amp. flush typenon modular switch as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material , minimum width of switch toggle should not less then18 mm, brass terminal & captive screws including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 145 Providing & Fixing ofof 3 pin 6 amp. flush typenon modular socket as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal with Porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 146 Providing & Fixing of ISI marked (IS:1258)6 ampbatten/angle lampholder as per PWD specification for electrical Works,made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screws including making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 147 P & F 18 swgM.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 148 Providing & Fixing of modular type Step Fan regulator duly ISI marked (IS :11037) as per PWD specification for electrical Works,made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith IP-20 rating , minimum width of 1 module switch toggle( PUSH PART ) should not less then 20mm,includingall as per pre approved by Engineer in charge,making connections, testing etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 149 Supply , Installation, Testing and Comissioning of Unmanaged Switch Plug-and-play - easysetup with no configuration or no software needed, following Port fast ethernet - 8 port10/100 MBPS auto-negotiation RJ45 ports, IEEE 802.3x flow control ,supports auto MDI/MDIX, eliminating the need for crossover cables including making connection etc asrequired complete in all respect. All as per pre approved by Engineer in charge. Foradditional technical parameters of products/ work , refer Annexure "A" attached with this 150 8 Port 151 24 Port 152 Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC,UTP (Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable asper latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balancedtwisted in pairs, seperated by a cross-member fluted pair divider & protected by PVCJacket. Certified performance in a 4-connector configuration upto 100 Mtrs channelrequirements & transmission frequencies up to 250 Mhz. in existing MS/PVCConduits/casing capping including making connections to Information outlets and PatchPanels with jack & ferruling at both ends for identification with necessary tools forpunching, stripping, crimping and testing etc as required complete in all respect. All as perpre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 153 Providing & Fixing of following modular accessories as per PWDspecification for electrical Works, made out of unbreakable and fireretardant vergin poly carbonate with brass terminals and captive screws &silver alloy contact tip with IP-20 rating , including all as per pre approvedby Engineer in charge,making connections, testing etc. as required. Foradditional technical parameters of product / work refer Annexure "A"attached with this BSRRJ-45, Cat 6 computer jack with shutter 154 Supply & Fixing of Water + AFFF 6% Mechanical Foam type Fire Extinguisher(Stored Pressure type) conforming to IS:15683:2018 , Powder coated Internal& External Surface Deep drawn cylinder body of Mild Steel CR2 gradeconforming to IS: 513, Squeeze grip Forged brass release valve with Inbuiltsafety release device, Diaphragm Type, 0 to 25 bar range pressure gauge, 450mm long EPDM discharge tube, QR code for Product Traceability includingFixing on wall with suitable Anchor Fasteners as required of followingcapacity. Test Certificates of all the Parameters along with Hydro test & Bursttest (For Cylinder Body) Certificate from OEM / External NABL AccrediatedLab is to be submitted. All as per pre approved by Engineer in charge. Foradditional technical parameters of products/ work , refer Annexure "A"attached with this BSR .Capacity - 9 Ltrs. 155 Providing & Fixing of 240/415 V isolator as per PWD specification for electrical Works with ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization catagory, 4KV impulse withstand voltage,true contact indication,Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting,minimum phase termination capacity of 35sq.mm. , label holding facility , IP 20 contact protection and fitted with existing distribution board / sheetincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab test reportsbefore execution & All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 156 Providing & Fixing of 18 SWG G. I. / M .S. Sheet boxesas per PWD specification for electrical Works, duly finished with two coats of red oxide and with earthing terminal of following sizes (nominal size) in recessed/surface as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 157 Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixturemade of powder coated single piece pressure die cast aluminum material with heat dissipation fins onhousing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass coverand secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125lm/ wt and potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with Highvoltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driver Efficiency >85%,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <750mA. The luminaireshall be BIS certified and Trade mark certified. Life Expectancy Equal or more than 50000 burning hrswith Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4KV internal and min 10 KV external inside driver compartment. driver should be Phase to phaseprotection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housingto allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its ownin house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report withliable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineerin charge. For additional technical parameters of products/ work , refer Annexure "A" attached with 158 Supply and erection of Mild steel Swaged tubular pole conforming to IS: 2713-1980 (part I to II) withbase plate, The pole shall be made from steel tube & Pipe (IS:1141, Fe 410) including excavation of the pitand filling the same with C.C. of M-20 grade (1:1.5:3) from base plate to 50 cm above ground level, withthe help of steel frame not less than 40 cm dia up to 114.3mm outer dia and 50 cm beyond 114.3mmouter dia around the pole. Duly finished with cement plaster, earthing terminals, cable entry with 32 mmdia. "B" class GI cable sleeves. After eraction pole shall be painted with two coat of red oxide primer andtwo quote of enamel paint of silver colour as per the direction of Engineer incharge complete as requiredof following height & designation. ( See Table P - 02 for specs. ) All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , refer Annexure "A" attached with thisBSR 7.5 Mtr. ( 410 SP - 5 ) 159 Supply and erection of Galvanized Iron pole with galvanizing done in single dipping (Average coatingthickness Minimum 65 Microns) continuously tapered poles having Octagonal / Circular cross-sectionsdesigned to withstand the maximum wind speed as per IS 875, The pole shaft shall be made from sheetsteel (HT Steel Conforming to grade S355JO) and confirming to BSEN 10025 and shall be continuouslytapered with single longitudinal welding. There shall not be any circumferential welding. The welding ofpole shaft shall be done by Submerged Arc Welding (SAW) process. pole shafts shall be provided with therigid flange plate of suitable thickness (Fe 410 conforming to IS 226 / IS 2062) with provision for fixing 4no. foundation bolts, This base plate shall be fillet welded to the pole shaft at two locations i.e. frominside and outside.The octagonal Poles shall have lockable door of approximate 500 mm length at theelevation of 500 mm from the Base plate with bakelite sheet having 6A SP MCB and 16 sqmm stud typeconnector ( 4 nos) inside the pole at door opening for cable connection of following length and dimensionas per table P-01 with base plate and foundation bolt on the Existing cement concrete foundation.All asper pre approved by Engineer in charge. For additional technical parameters of products/ work , referAnnexure "A" attached with this BSR12 Mtr 160 Providing & Fixing of IK08 IP-66 protected high power LED flood light system with single piece Pressurediecast aluminium housing, toughened glass diffuser with suitable lenses on LED to achieve various beamangles, of high power LED of 3 to 5 watt each . Integrated potted driver as a unique BIS R number havingefficiency more than 85 % and in compliance to BIS certified and Trade mark certificate. The System levelLuminaire efficacy >=125 lm/ wt. LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff@>=300 V AC and Auto resetting Safety .Power Factor >0.95 , THD(I) <10% , driver current <=750mA.driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector , Surge Protection Min>=4KV internal and 10KV external but inside driver compartment, System life of 50000 Burning hourswith 70% of Initial Lumens maintained, CRI>70 and CCT 5700K ±355K. Manufactures Word Mark/NameEngraved/Embossing/Screen printing on die cast housing to allow traceability/authenticity. Fixture shallbe IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LEDfixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shallbe submitted. All as per pre approved by Engineer in charge. For additional technical parameters ofproducts/ work , refer Annexure "A" attached with this BSR . High power LED flood light Minimum Lumen output 43750 Im 161 Boundry 162 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds of soils 163 Supply & stacking good earth at site complete including loading , unloading and transportation etc &Filling available excavated earth (excluding rock) in trenches plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead upto 50 Mtr. and lift upto 1.5 Mtr. 164 P.C.C. IN FOUNDATION Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:4:8 (1 cement:4 Coarse sand :8 gradeed stone aggregate 40 mm nominal size). 165 Random Rubble stone masonry with hard stone in superstucture above plinth level and upto five level wall upto 30 cm and less thickness cement sand mortar 1:6 (1-Cement: 6- Sand) 166 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size). 167 STONE MASONRY IN SUPER STRUCTURE Random Rubble stone masonry with hard stone in superstucture above plinth level and upto five level wall upto 30 cm and less thickness cement sand mortar 1:6 (1-Cement: 6- Sand) 168 Pillar Masonary :- Random Rubble stone masonry with hard stone in superstucture above plinth level and upto five level for square or rectangular pillers cement sand mortar 1:4 (1-Cement: 4- Sand) 169 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished : 20 mm thick 170 Exterior Finishing: Finishing wall with water proofing cement paint of appd brand & manufacture and of reqd. shade to give an even shade including all scafolding New work (three or more coats applied at the rate of 3.84 kg/10 sqm) 171 PANTING ON DOORS & WINDOWS:- Painting with syntheitic enamel paint of approved brand and manufacture in all shade to give an even shadenew steel work (2 or more coat on new work). 172 COPING:-Providing and laying cement concrete including curing compaction etc. complete in retaining walls, return walls, walls(any thickness) including attached pilasters, columns, piers, abutments, pillers, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc upto floor five levelexcluding the cost of centeringand shuttering.M15 grade nominal mix 1:2:4(1 cement:2 Coarse sand :4 gradeed stone aggregate20 mm nominal size). 173 Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor r Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix 174 Random rubble dry stone kharanja under floor 175 Kerb Stones of 1200x300x150, 1000x450x150,1000x600x150, 600x300x150 size (M-30)Providing and Laying cement concrete Kerb Stones ofdifferent sizes in M-30 grade (Manufactured with fullymechanised dry cast process with forced action mixer whosearms revolve along the main axis and rotate about its own axisalso, having humidity sensor for moisture control of w/c ratioin concrete mix. Manufactured with steel moulds (Milled andmanufactured in CSI diamond or CSI Nitro process foraccuracy) on steel base plate of min 16 mm thick; HavingVibration and pressing action both together with the help ofmultiple synchronised vibrators. Power of hydraulic stationshould be minimum 50KW for compaction and cured incontrolled chambers having humidity control and automatedair circulation system) in position to the required line, leveland curvature jointed with cement mortar 1:3 (1 Cement : 3Coarse sand) including making of joints, drainage openingwherever required 176 Providing and fixing steel gate, grating , and grills made of angles,tees, square bars, flats,or black pipe with holdfast and fittings completeas per design and drawing including cutting welding and fabricationwith priming coat of red oxide 177 Providing and laying of paver block as per IS 15658 : 2006(Indian standard for precast concrete block for paving specification) and IRC : SP:63-2004 (guidelines for the use ofinterlocking concrete block pavement)M-30, 60 mm thick to be used in non traffic areas like buildingpremises, monument premises, land scapes, public gardens/park, domestic drives, paths and patios, Embankment slopes,sand stabilization Area etc.( As per table 1 of IS 15658:2006(A) Category A Denated units to key into each other on four faceszigzag shape as per IRC SP 63:2004 178 Tubewell 179 Construction to tube well from ground levels and upto 100 meter depth and above to accommodate housing and assembly pipe of following sizes in all types of alluvium strata by percussion/ rotary drilling method and with gravel as per IS : 4097-1967 and packing as per IS : 2800 ( Part I & II ) 1979 as amended upto date ( the work includes the cost of gravel & its primary packing and packing during development. lowering of housing & strainer assembly pipes, with supply and wrappiing of coir rope, wherever necessary, for arresting fine sand particles. The work will not include cost of housing pipe and strainer pipe assembly and development work, but work would be completed after obtaining sand free water.) 180 150 mm Nominal Bore. 181 Construction ofTube well upto 100 meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per IS : after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe. 182 150 mm Nominal Bore. 183 Development of tube well as per ISI specification using suitable compressor to give free water for required yield of the gravel packed tube well. 184 Supply fo ERW M.S. black casing pipe ISI marked ( IS : 4270/1992) of grade Fe410 of following sizes at site of work. Nominal bore of pipe (mm) 185 150 mm nominal boae of pipe 186 Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size fo slotting as pe IS: 8110 1985 187 150 mm nominal boae of pipe 188 Testing verticality of tube well by plumbing system and yield test and draw test by pumping system as per IS : 2800 (Part II) 1979. 189 S & F tube well cover fo M.S. sheet (6mm thick) with nuts and bolts complete forsize. 190 150 mm dia 191 S & F M.S. Clamp, set of 50 X6 mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. 192 Supplying and installation fo 32 mm dia G.I. pipe medium class IS 1239 marked in 3m length including all accessories and fittings required for installation of Submercible Pump sets. 193 Supply Installation testing & Commissioning of Radial / mixed flow ISI marked water filled submersible motor pump setssuitable for 100/150mm dia borewell.The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034:2018 and IS 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008,& IS12615:2011with required accessories including making connection suitable for Bore well. The job includes labour part of lowering ofriser pipe G.I./H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to switch board. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect . All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 194 3.0 HP, 1-Ø, (40 -170)Mtr, (60- 20) LPM 195 Supplying and Laying ISI marked P.V.C. insulated submersible cable as per PWD specification for electrical Worksconfirming to IS:694 and as per IS 8130 : 2013 of 1.1 kV grade .Wire should be made from99.99% purity copper, class 5 stranding in acc. to IEC 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4 including making connection etc. as required.OEM Must have its own in house NABL lab setup for all testing facilities for wires. All as per pre approved by Engineer in charge, making connections.For additional technical parameters of products/ work, referAnnexure "A" attached with this BSR . 196 4.0 Sq.mm 3 core flat / Round 197 Supply Installation testing & Commissioning ofISO certified company made DOL/Star-Delta Starter panel made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFFpush buttons,ammeter, voltmeter, indicating lamps etc.suitable for following rating motors complete in all respect. Appropriate type test certificate / OEM test report shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . For single phase Submersible / Monoblockpump0.5 HP to 3.0 HP (DOL starter) 198 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds of soils 199 PCC in foundation :Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:3:6(1 cement:3 Coarse sand :6 graded stone aggregate 20 mm nominal size). 200 Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix 201 Centering & shuttering with plywood or steel sheets includingstrutting, propping bracing both ways with steel props andremoval of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 202 Brick masonry with F.P.S. bricks of class designation 75 infoundation and plinth with bricks Cement mortar 1 : 4 (1 cement : 4 coarse sand) 203 Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. Thermo-mechanically Treated bars (Conforming of relevent IS code) 204 External Plaster : Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished 20 mm thick 205 Grading roof for water proofing treatment withwater proffing compound: Cement concrete 1: 2: 4 (1 cement: 2 Course sand: 4 Greded stone aggregate 20 mm nominal size) 206 Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. 207 Exterior finishing :- Finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. New work (two or more coat applied @1.67/ ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm.)Qty as per item no.7*0.5 208 R/R Dry stone kharanja under floor 209 securty 210 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds of soils 211 PCC in foundation :Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:4:8(1 cement:3 Coarse sand :6 graded stone aggregate 40 mm nominal size). 212 Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in cement mortat 1:6 (1-Cement: 6- Sand) 213 Brick work with clay flyash F.P.S. brick(IS 13757- 1993 ) of class designation 75 in superstructureaboveplinth level upto floor five level in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) 214 Stone Kharanja: Random rubble dry stone kharanja under floor 215 Half Brick work with mechanised autoclaved flyash lime bricks conforming to IS: 12894 :2002 of class designation 100 in superstructure above plinth level upto floor V level in.C.M.1:4 216 Providing & Fixing Ist quality standard White, gray, ivory,fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 and IS: 15622 of size 300mm x 200mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster on walls and piller) 217 Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirmingto IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). 218 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 219 Door Frames : P & FT- iron frames for doors , windows and ventilators of mild steel , Tee section joints mitred and welded with 15x3 mm lugs 10 cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement:3 fine sand6 graded stone aggregate 20 mm nominal size:) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required including fixing of necessary butt hinged and screws and applying a priming coat of approved steel primer 220 Providing and fixing M.S. sheet 1mm thickSingle leaf door shutter windows in angle iron frame35x35x5 mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint 221 Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. 222 6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3 - fine sand) 223 ExternalPlaster : Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished 20 mm thick 224 InternalPlaster : Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished 12 mm thick 225 Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for :Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc 226 Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix 227 Cement concrete 1: 2: 4 (1 cement: 2 Course sand: 4 Greded stone aggregate 20 mm nominal size) 228 Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitred weldedand grinded including hold fast of steel lugs 13mm x 3mm and 15 Cm long embedded in C Cblock 15 x 10 x 10 Cm of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred and grinded including 10mm x 10mm square bars welded to framefor paitam fixing float glass 4mm thickpanes with glazing clips and metal sash putty andfixing of shutters frames peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of Engineer-in –charge 229 Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 230 Providing and fixing Square bars or other flat welded to window, ventilatiors etc. 231 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:Newwork(twoormorecoats)overandincludingscrappingandprimingcoatwithcement primer 232 PANTING ON DOORS & WINDOWS:- Painting with syntheitic enamel paint of approved brand and manufacture in all shade to give an even shadenew steel work (2 or more coat on new work). 233 Copping: Cement concrete flooring 1:2:4 (1 cement: 2 Course sand: 4 Greded stone aggregate) finishing with a floating coat of neat cement including cement slurry, making of lines or groove etc. complete but excluding the cost of nosing of steps etc. complete : 40mm thick with 20mm thick nominal size aggregate. 234 based on PWD BSR 2019 235 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,)20mm nominal outer dia pipes 236 25 mm nominal outer dia pipes 237 P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: 238 P & F WVC wash basin (1st quality, I.S. : 2556 Mark) of approved make with C.I. brackets duly painted, 1 No. 15 mm C.P. Pillar cock (IS : 8934 Mark) &32 mm C.P. brass waste coupling of approved make,25 mm G.I. waste pipe complete including cutting & making good the wall.: 450 x 300 mm 239 P&FFlushCock / FlushValve (IS :9758Mark)forWCofapproved quality make :(-do-) concealed 25mm nominal bore. 240 P & F Bib Cock (IS : 8931 Mark) superior quality of approved make.C.P. Brass 400 gm, 15 mm nominal bore. 241 P & F Inlet connection (Angle Valves) Superior quality of approved make C.P. Intel connection 15 mmbrass(IS : 8931) 242 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia 243 P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall: 244 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: Bend 87.5110mm dia 245 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant Plain floor trap 110 mm dia 246 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant P-Trap 110 mm dia 247 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant Vent Cowel 110 mm dia 248 S/F RCCmain hole covers with frame of approved make (Light Duty) Size 450x450 mm 249 P/F Grating of Approved quality Stainiese Steet sheet size 125 mm dia 250 Construction of Soakage well in alltypes of soil of approved drawing , top 90 cm portion in 450 mm thick with cement mortar 1:6 80 mm stone slab coveringjointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C. flooring earthwork etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 Mtr.inner dia 90 cm & 10 to 12 m deep 251 Construction of Chamber in all types of soil with 300 mm thick masnory in CM. 1 : 6, 100 mm thick C.C. 1 : 5 : 10 in foundation , 20 mm thick inside plaster in Cm 1 : 6, finished with floating neat cement 50 mm thick M-15 grade C.C. flooring earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 Mtr.Inside size 450 x 450 mm depth upto 0.5 M & 5 Kg CI cover with frame. 252 P & F Ball Cock (IS : 1703 Mark) with Rod & P.V.C. Ball complete.Brass wt. 400 gm, 15 mm 253 P & F 15 mm dia connection pipe of approved quality make PVC Pipes with nuts 450 mm. 254 P & F Stop cock (IS:8931 Mark),Superior quality and of approved mark: Brass 400 gm. 15 mm nominal bore 255 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,) 15 mm dia 256 32mm nominal outer dia pipes 257 P & F PVC Storage Tank ISI Marked ( IS: 12701) indicating the BIS license No. of approved make with cover, 25mm dia 1 M long G.I. overflow pipe & 25 cm longwash out pipe with plug & socket including making connection etc. complete of approved design 500 litres capacity 258 Rain water Harvesting 259 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds of soils 260 PCC in foundation :Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:3:6(1 cement:3 Coarse sand :6 graded stone aggregate 20 mm nominal size). 261 Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix 262 Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 263 Brick masonry with Fly ash F.P.S. bricks of class designation 75 infoundation and plinth with bricks Cement mortar 1 : 4 (1 cement : 4 coarse sand) 264 Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. Thermo-mechanically Treated bars (Conforming of relevent IS code) 265 External Plaster : Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished 20 mm thick 266 Grading roof for water proofing treatment withwater proffing compound: Cement concrete 1: 2: 4 (1 cement: 2 Course sand: 4 Greded stone aggregate 20 mm nominal size) 267 Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. 268 Exterior finishing :- Finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. New work (two or more coat applied @1.67/ ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm.)Qty as per item no.7*0.5 269 R/R Dry stone kharanja under floor 270 P& F rigid PVC Pipe (IS 4985 Mark) Class 2nd /(4 kg /sqcm) approved quality / Make including joining the pipe with solvant cement rubber ring and lubricant. (A)110 mm dia. 271 (B) 160mm dia. 272 Construction of manhole in all type of soil inner size 90X60 cm. thick cement concrete 1:50:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C flooring, making channels, 80 mm thick stone slab covering with 40 mm thick M-15 grade C.C flooring, cement cover with frame of 450 mm dia, earthwork etc. complete as per design including disposal of surplus earht within 50 mtr. lead. Depth up to 0.5m 273 Construction of chambers in all type of soil with 300 mm thick mesonary in cement sand mortar 1:6 100 mm thick CC 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6 finished with floating neat cement ,50 mm thick M-15 grade CC flooring , Earth work etc. complete as per design including disposal of surplus earth within a lead of 50 Mtr.Inside size 300X300 mm depth upto 0.5 Mtr. And 5 kg. CI cover with frame .

Contact Information